• 한국측량학회:학술대회논문집
• /
• 한국측량학회 2003년도 추계학술발표회 논문집
• /
• pp.373-378
• /
• 2003

This study deals with development of transformation tool for transformation of digital map coordinates systems using by the best fit transformation parameters which are determined between the local geodetic datum and geocentric datum (ITRF2000) in Korea and distortion modelling derived from collocation method. We used 107 control points as a common points. For analyzing the derived parameters, another 83 common points are tested. Finally, the best fit parameters are determined from Molodensky-Badekas model after considering the RMSE, maximum value, minimum values, and 95% confidence interval of residuals. after transformation of best fit parameters and distortion modelling, we could develop transformation tools with advenced accuracy. so it is possible to perform on transformation of digital map with scale 1:5,000. and we tested accuracy eveluation through analysis between transformation results and field results of GPS observation.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제49권6호
• /
• pp.380-386
• /
• 2000

This paper presents the mathematical modelling analysis of Brushless Synchronous Motor(BLSM). The dynamic and the steady state characteristics of BLSM are simulated and analyzed : electromagnetic torque, speed, line voltage, and current. We used mathematical modelling to model of BLSM with sinusoidal back EMF, namely the shaft transformation referencing rotor frame from a, b, c three to produce constant torque like synchronous motor. The experiment result has already similar to compare with simulation result : torque error about 7%, speed error about 5%. The validity of proposed modelling and analysis was confirmed by the experimental result.

• Wind and Structures
• /
• 제32권1호
• /
• pp.11-17
• /
• 2021

In recent years, there has been a tendency towards renewable energy sources considering the damages caused by non-renewable energy resources to nature and humans. One of the renewable energy sources is wind and energy is obtained with the help of wind turbines. To determine the behavior of wind turbines under earthquake loads, dynamic characteristics are required. In this study, the differential transformation method is proposed to determine the free vibration analysis of wind turbines with a variable cross-section. The wind turbine is modeled as an equivalent variable continuous flexural beam and blade weight is considered as a point mass at the top of the structures. The differential equation representing the free vibration of the wind turbine is transformed into an algebraic equation with the help of differential transformation method and the angular frequencies and the mode shapes of the wind turbine are obtained by the help of the differential transformation method. In the study, a sample taken from the literature was solved with the presented method and the suitability of the method was investigated. The same wind turbine example also modeled by finite element modelling software, ABAQUS. Results of the finite element model and differential transformation method are compared with each other and the results are in good agreement.

• 응용통계연구
• /
• 제6권2호
• /
• pp.253-263
• /
• 1993

최근 다구찌 실험에 대한 관심이 고조되어 일반화 선형모형에서 평균과 분산의 동시모형화가 연구되고 있다. 하나의 자료 변환만으로는 자료분석에 필요한 모든 조건들을 만족시킬 수 없기 때문에 다구찌 품질실험의 자료들을 일반화 선형모형으로 분석하는 것이 바람직하다. 본 논문에서는 이 자료변환법과 일반선형모형을 이용한 분석법을 소개, 비교하고 일반화 선형모형을 다구찌 자료에 적용할 수 있는 GLIM 프로그램을 제시한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1988년도 한국자동제어학술회의논문집(국내학술편); 한국전력공사연수원, 서울; 21-22 Oct. 1988
• /
• pp.562-566
• /
• 1988

The purpose of this study is to develop a personal computer aided 3-D geometric modeller. To perform this study, we set up a cube, a cylinder, and a prism as a primitive in the first segment of this study. By modelling the 3-D object through their transformation, addition, and subtraction, we proved the validity of the developed algorithm and its computer program. Some examples show the results of applying the program to modelling a few simple shape of the machine parts. These results met the first aim of this study.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.196-201
• /
• 2000

A thermodynamic model was developed to analyze the characteristics of the heat generation during transformation of austenite in 0.186wt% and 0.458 wt%. carbon steels. The heat capacity and the heat evolved during transformation were formulated as functions of temperature and chemical composition for ferrite bainite and pearlite. in addition using the transformation dilatometer the transformation heat evolved during cooling was measured and the transformation behavior was observed. It was found that the heat capacity of ferrite was similar to those of pearlite and bainite. The heat capacity of ferrite was greater than that of bainite which was greater than that of pearlite. The molar heat of transformation to pearlite was greater than that to bainite which was greater than that to ferrite. The heats were found to be increased with decreased temperature and increasing the carbon content, It was also observed that the thermodynamic model. The heat of transformation in the higher carbon steel was greater than that in the lower carbon one. This was attributed to the lower transformation temperature and the greater amount of transformed pearlite in the higher carbon steel.

• 대한토목학회논문집
• /
• 제32권4D호
• /
• pp.407-419
• /
• 2012

현재 우리나라의 국가수직기준체계는 육상과 해상으로 서로 이원화되어 있어 전 국토에 걸쳐 균일하고, 정확한 높이정보를 획득하기 어려운 문제가 있다. 본 연구에서는 국토지리정보원에서 수행한 TBM 및 BM 간 연결 수준측량 성과를 이용하여 육상과 해상으로 이원화된 국가수직기준체계의 문제점을 해결하고자 하였다. 이를 위해 정밀 수준측량으로 결정된 육상과 해상 수직기준면 간 편차를 모델링하여 육상 해상 수직기준면 연계를 위한 변환모델을 개발하였다. 보다 정밀한 수직기준면간 변환모델링 방안을 제시하기 위하여 LSC 및 Spline 방법 등 다양한 보간방법들에 의한 결과를 분석하였으며, 그 결과 비선형의 4-파라미터 경향성 모델과 LSC 방법을 조합하여 개발하는 방안이 가장 적합하였다. 이 방법에 의해 개발된 수직 기준면 변환모델의 정확도는 약 ${\pm}10.4cm{\sim}14.8cm$ 수준으로 분석되었으며, 변환모델을 사용하여 다양한 공간정보의 높이정보를 효율적으로 변환할 수 있는 변환 소프트웨어도 함께 개발하였다. 본 연구를 통해 육상 및 해상 국가공간정보의 연계 활용 시에 높이정보 불일치로 인한 혼란을 최소화할 수 있을 것으로 기대되며, 향후 연안지역 개발과 해양방재의 수행에 있어서도 경제적, 시간적 손실을 최소화할 수 있을 것으로 판단되었다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 V
• /
• pp.2827-2830
• /
• 2003

Tele manipulator is distingushed from industrial robot by iterating same specified work. Manipulator operator is included in control loop for controlling the telemanipulator because he decide directly during the work and order controllabily reducing the modelling error of telemanipulator which depend on the PID controller. But position-force control method of bidirectional control impose unsafety of vibiration and Analytic Hierachy Method can stabilize for reducing nonlinear modelling error by expert operator because of transformation empirical control rule to linear model.

• 대한원격탐사학회지
• /
• 제36권1호
• /
• pp.15-27
• /
• 2020

Accurate knowledge of land use/land cover (LULC) features and their relative changes over upon the time are essential for sustainable urban management. Urban sprawl growth has been always also a worldwide concern that needs to carefully monitor particularly in a developing country where unplanned building constriction has been expanding at a high rate. Recently, remotely sensed imageries with a very high spatial/spectral resolution and state of the art machine learning approaches sent the urban classification and growth monitoring to a higher level. In this research, we classified the Quickbird satellite imagery by object-based image analysis of Dempster-Shafer (OBIA-DS) for the years of 2002 and 2015 at Karbala-Iraq. The real LULC changes including, residential sprawl expansion, amongst these years, were identified via change detection procedure. In accordance with extracted features of LULC and detected trend of urban pattern, the future LULC dynamic was simulated by using land transformation model (LTM) in geospatial information system (GIS) platform. Both classification and prediction stages were successfully validated using ground control points (GCPs) through accuracy assessment metric of Kappa coefficient that indicated 0.87 and 0.91 for 2002 and 2015 classification as well as 0.79 for prediction part. Detail results revealed a substantial growth in building over fifteen years that mostly replaced by agriculture and orchard field. The prediction scenario of LULC sprawl development for 2030 revealed a substantial decline in green and agriculture land as well as an extensive increment in build-up area especially at the countryside of the city without following the residential pattern standard. The proposed method helps urban decision-makers to identify the detail temporal-spatial growth pattern of highly populated cities like Karbala. Additionally, the results of this study can be considered as a probable future map in order to design enough future social services and amenities for the local inhabitants.

• 한국측량학회지
• /
• 제22권1호
• /
• pp.29-36
• /
• 2004

본 연구는 구 데이텀으로 구축된 수치지도를 지구 중심 데이텀으로의 변환에 필요한 새로운 변환 파라미터를 결정하고, 콜로케이션 방법으로부터 유도된 왜곡 모델링을 적용한 수치지도 좌표계의 변환에 관한 것이다. 국토지리정보원에서 GPS관측을 실시한 정밀 1차 기준점 190점 중에서 107점의 공통점을 파라미터 결정으로 사용하였으며, 최적 변환 파라미터의 결정을 위하여 107점을 제외한 83점의 공통점을 변환 정확도 검증에 이용하였다. 통계 분석을 통해 Molodensky-Badekas 모델로부터 산출된 파라미가 최적 파라미터로 결정되었으며, 왜곡 모델링을 수행한 결과 0.22m의 변환 정확도를 얻었다. 이는 7 파라미터만을 이용한 변환보다는 72%의 정확도가 향상된 결과를 나타내는 것이다. 또한, 1/50,000, 1/25,000과 1/5,000 수치지도의 변환 도구인 GDKtrans를 개발하였다. 이 변환 도구를 이용하여 6개 대도시 지역의 l/5,000 수치지도를 변환하고, 검사점 GPS 측량을 실시하여 변환정확도를 검사한 결과 약 1.9 m의 변환 정확도를 보였으나, l/5,000 수치지도의 위치 정보와 형상이 실제 위치 및 형상과 크게 일치하지 않고 있어 전면적으로 l/5,000의 수치지도를 재 제작하는 것이 타당하다고 판단된다.