• The Journal of the Acoustical Society of Korea
• /
• v.13 no.2
• /
• pp.68-75
• /
• 1994

This is the second of two companion papers wich describes the wideband array transducer design procedure and the designed transducer acoustic characteristics. In addition, the result of the designed transducer acoustic characteristics by the combined Finite Element Method and Hybrid Type Infinite Element Method, is found to better than that by the equivalent circuit model method. Therefore, the technique presented in this paper could be applied in the design and the acoustic characteristics analysis of the wideband array transducer.

• Smart Structures and Systems
• /
• v.8 no.4
• /
• pp.413-431
• /
• 2011

Under the external shearing stress, the external radial stress and the electric potential simultaneously, the piezoelectric hollow cylinder transducer is studied. With the Airy stress function method, the analytical solutions of this transducer are obtained based on the theory of piezo-elasticity. The solutions are compared with the finite element results of Ansys and a good agreement is found. Inherent properties of this piezoelectric cylinder transducer are presented and discussed. It is very helpful for the design of the bearing controllers.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.3
• /
• pp.282-289
• /
• 2009

This paper presents an estimation technique of the equivalent circuit parameters for an underwater acoustic piezoelectric transducer from the measured impedance. Estimated equivalent circuit can be used for the design of the impedance matching network of the sonar transmitter. A fitness function is proposed to minimize the error between the calculated impedance of the equivalent circuit and the measured impedance of the transducer. The equivalent circuit parameters are estimated by using the fitness function and the PSO(Particle Swarm Optimization) algorithm. The effectiveness of the proposed method is verified by the applications to a sandwich-type transducer and a dummy load. In addition, the impedance matching network is also designed by using the estimated equivalent circuit model.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.5
• /
• pp.572-581
• /
• 2008

The performance of a barrel stave flextensional transducer is determined by the properties of its constituent materials and the effects of many structural parameters. In this study, with the finite element method, the structure of a barrel stave flextensional transducer was optimized to achieve the widest bandwidth while satisfying the requirements on pressure and center frequency. The optimization was carried out with the SQP-PD method for multi-variable minimization. The optimized barrel stave flextensional transducer satisfied all the required specifications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.744-750
• /
• 2001

Higher directivity acoustic transducer using the self-demodulation effect was fabricated. The structure of transducer was designed such as dimension and support type of the piezoelectric element, the vibrating metal plate, and the housing case. Based on the design, the transducer was fabricated and measured its acoustic characteristics. Also, AM modulated driving circuit was designed for using the self-demodulation effect. The piezoelectric sounder with 200kHz resonant frequency and 20kHz bandwidth was designed by considering the sharp directivity and the sound pressure. The design and fabrication method worked in this study can be utilized in development of various speakers with higher directivity and broader bandwidth.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.196-200
• /
• 2005

Piezoelectric underwater acoustic transducer is a kind of device for underwater detection working as not only an actuator but also a sensor. The technique that can predict acoustical characteristics of transducer is important for robust design of transducer in harsh underwater environment. This paper represents the dynamic analysis of piezoelectric acoustic transducers based on finite element method through USAP software. Two dimensional model of Tonpilz transducer and three dimensional model of Flextensional transducer are generated for the dynamic analysis and some results obtained by USAP are compared with those by ANSYS.

• The Journal of the Acoustical Society of Korea
• /
• v.39 no.2
• /
• pp.87-97
• /
• 2020

In this paper, the design of piezoelectric Micro-machined Ultrasonic Transducer (pMUT) for wideband ultrasonic radiation in air was investigated. One of the methods to achieve wide frequency bandwidth in single device is modeling the transducer to multi-resonance system. The new pMUT was designed as a multi-resonance system with the addition of a suitable acoustic structure to the front and back of a thin film structure. A new pMUT consisting of thin film parts, radiation parts, and packaging parts is designed with a Lumped Parameter Model (L.P.M). Finally, it was validated as a Finite Element Method (FEM) simulation. The final designed pMUT achieved a frequency band of 102 kHz ~ 132 kHz (-3 dB).

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.4
• /
• pp.629-635
• /
• 2017

Free-Flooded Ring (FFR) transducer array for use in Sonar system can be driven with large amplitude in a wide frequency band due to its structural characteristics, in which two resonances of a ring mode (1st radial mode) and an inner cavity vibration mode occur in a low frequency band. Since its sound wave generation characteristics are not influenced by the water pressure, the FFR transducer array is widely used in the deep sea. So FFR has been recognized as a low-frequency active sound source and has received much attention ever since. In order to utilize the FFR transducer array for SONAR systems in military and industrial applications, its equivalent electric circuit model is necessary especially to design the matching circuit between the driving power amplifier and the FFR transducer array. Thus this paper proposes the equivalent electric circuit model of FFR transducer array by using measured values of parameter, and suggest the improved method of parameter identification. Finally it verifies the effectiveness of the proposed circuit model of FFR transducer array by experimental measurements.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.466-472
• /
• 2016

In this work, a medical linear array ultrasonic transducer working in the range of 20 MHz has been developed for high-resolution ultrasonic imaging. After devising the structure of the transducer suitable for the transmission of high-frequency waves, we optimized the dimension of constituent components. Then, the process to fabricate the transducer was developed to realize the designed structure, and a prototype of the transducer was fabricated and characterized. The center frequency of the fabricated transducer was measured to be 19 MHz, and the fractional bandwidth to be 84.5 %, and the standard deviation of the sensitivity over the entire channels to be 0.74 dB. These measurement results showed good agreement with design data, which confirmed the validity of the high frequency ultrasonic transducer structure developed in this work. It was confirmed that the developed transducer with new structure had wider frequency bandwidth and uniform sensitivity than a conventional 20 MHz transducer.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.2
• /
• pp.173-183
• /
• 2010

In a split beam echo sounder, the transducer design needs to have minimal side lobes because the angular position and level of the side lobes establishes the usable signal level and phase angle limits for determining target strength. In order to suppress effectively the generation of unwanted side lobes in the directivity pattern of split beam transducer, the spacing and size of the transducer elements need to be controlled less than half of a wavelength. With this purpose, a 50 kHz tonpilz type transducer with a half-wavelength diameter in relation to the development of a split beam transducer was designed using the equivalent circuit model, and the underwater performance characteristics were measured and analyzed. From the in-air and in-water impedance responses, the measured value of the electro-acoustic conversion efficiency for the designed transducer was 51.6%. A maximum transmitting voltage response (TVR) value of 172.25dB re $1{\mu}Pa/V$ at 1m was achieved at 52.92kHz with a specially designed matching network and the quality factor was 10.3 with the transmitting bandwidth of 5.14kHz. A maximum receiving sensitivity (SRT) of -183.57dB re $1V/{\mu}Pa$ was measured at 51.45kHz and the receiving bandwidth at -3dB was 1.71kHz. These results suggest that the designed tonpilz type transducer can be effectively used in the development of a split beam transducer for a 50kHz fish sizing echo sounder.