• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.5
• /
• pp.253-263
• /
• 2021

Traffic data collected using advanced equipment are highly valuable for traffic planning and efficient road operation. However, there is a problem regarding the reliability of the analysis results due to equipment defects, errors in the data aggregation process, and missing data. Unlike other detectors installed for each vehicle lane, radar detectors can yield different error types because they detect all traffic volume in multilane two-way roads via a single installation external to the roadway. For the traffic data of a radar detector to be representative of reliable data, the error factors of the radar detector must be analyzed. This study presents a field survey of variables that may cause errors in traffic volume collection by targeting the points where radar detectors are installed. Video traffic data are used to determine the errors in traffic measured by a radar detector. This study establishes three types of radar detector traffic errors, i.e., artificial, mechanical, and complex errors. Among these types, it is difficult to determine the cause of the errors due to several complex factors. To solve this problem, this study developed a radar detector traffic volume error analysis model using a multiple linear regression model. The results indicate that the characteristics of the detector, road facilities, geometry, and other traffic environment factors affect errors in traffic volume detection.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.5
• /
• pp.22-35
• /
• 2013

With the increase in image detectors, concerns about the reliability of traffic information are increasing. In this paper, we propose a method to generate reliable traffic volume using analysis of the point detector data as a representative value. Therefore, targeting expressway, we analyzed the difference in traffic volume collected by loop and image detector, and verified statistically using t-test, and finally analyzed the error rate compare to the real traffic volume. Analysis revealed that there was a statistically difference the traffic date collected by the loop detector and the image detector, in the same period, the same time, respectively. In addition, the difference between the actual traffic volume and traffic that have been collected in a loop detector was the lowest Therefore, creating a traffic volume of representative value, we proposed a method to use loop detector than the average traffic volume collected by each detector. It shows that it is more important to use one high-quality data rather than various low-quality data to produce a representative value.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1689-1693
• /
• 2004

This paper proposes a vehicle detector with a magnetoresistive (MR) sensor. The detector consists of a MR sensor and mechanical and electronic apparatuses. Composed of six magnetically variable resistors, the MR sensor senses disturbance of the earth's magnetic field caused by a moving vehicle over itself and then produces an output indicative of the moving vehicle. Experiments have been carried out with three stages. At the first stage, the outputs of the sensor have been analyzed to show the validity of the detector's circuit and the detecting method. At the second stage, the detector has been tested on a local highway in Korea. Through the field tests, the outputs of the detector in response to various kinds of moving vehicles have been collected and analyzed. At the final stage, to verify the performance of the detector, traffic volumes on the highway have been measured with the detector and compared with the exact traffic volumes in a highly congested traffic.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.3
• /
• pp.600-605
• /
• 2011

This paper shows field test and evaluation results for a wireless vehicle detector with anisotropic magneto-resistive (AMR) sensors. The detector consists of two AMR sensors and mechanical and electronic apparatuses. The AMR sensor senses disturbance of the earth magnetic field caused by a vehicle moving over the sensor and then produces an output indicative of the moving vehicle. In this paper, vehicle speeds are calculated by using two AMR sensors fixed on a board, with constant distance. To test and evaluate the accuracy of the detector in real traffic situations, the detector was installed on a local highway and vehicle speeds and volumes were measured both in a free running and a highly congested traffic. The measurements from the detector are compared with the reference measurements obtained from a traffic camera with the Mean Absolute Percentage Errors (MAPE), which has proved the usefulness of the detector in the field.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.157-163
• /
• 2003

This paper proposed a new type of vehicle detector using a MR sensor. and addressed detector's apparatuses and detecting algorithms. Proposed detector has been tested on a local highway between Mishiryong and Sokcho in Korea. Through extensive field tests, the outputs of the detector in response to various kinds of passing vehicles have been collected and analyzed. It is verified from the analyses that the outputs of the detector take on very different aspects with each vehicle, so that information on not only traffic count but vehicle types could be extracted from the outputs. And, with the proposed detector, traffic volumes on the two lanes in the tested region were measured and compared when both congested and clear traffic situations.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2956-2958
• /
• 2000

This paper describes the design of a real time traffic data acquisition system using loop detector and piezzo sensor. Loop detector is the cheapest method to measure the speed and piezzo is used to detect the vehicle axle information. A ISA slot based I/O board is designed for data acquisition and PC process the raw traffic data and transfer the data to the host system. Simulation kit is designed with toy car kits. simulated loop detector and piezzo sensor. The data acquisition system collects up to 10 lane highway traffic data such as vehicle count. speed. length axle count. distance between the axles. The data is processed to generate traffic count, vehicle classification, which are to be used for ITS. The system architecture and simulation data is included and the system will be tested for field operation.

• The Journal of the Korea Contents Association
• /
• v.21 no.1
• /
• pp.119-128
• /
• 2021

The most typical method to generate traffic information is installing vehicle detectors and collecting various traffic variables. The information collection accuracy of a vehicle detector affects the reliability of the generated traffic information. The most universal vehicle detector is an image detector. This study installed a magnetic detector in the same position as an image detector and evaluated the accuracy of traffic volume and speed data depending on a variety of environment. Based on the evaluation, more errors occurred as the image detector was placed farther from the camera, whereas more errors were found to occur during the night rather than the day. Although rainfall did not affect the collection of traffic volume, it negatively affected speed data collection. Therefore, an analysis of the camera's view angle and its optimization depending on the camera installation position and height are required to enhance the currently operated image detector performance. It is judged that a separate performance evaluation criterion should be prepared in a bad weather environment.

• 전기의세계
• /
• v.22 no.1
• /
• pp.35-41
• /
• 1973

An automatic point traffic control method is recommended for more idealistic traffic flow over coarse road netowrks. The automatic control apparatus recommended, consists of a transceiver, amplifier, digital-to-analog converter, signal light controller for emergency and steady state, and digital counter as monitor. The transmitter sends a signal to the target vy means of Microwave-FM-CW and a diode detector picks up the echo signal. Thus the operation of the entire system will be carried out through an open loop state. Some factors necessary for an ideal detector system are rapid response, longevity and stability. An analytical method of the Doppler effect substitutes the conventional frequency deviation into the amplitude of detector output. The changing rate of amplitude is proportional to the voltage of the detector output. Some induced formula from Maxwell's radiation field theory ensures this new method, and, new method, and proves the fact with an experimental data presentation. Stability depends upon Klystron as an oscillator and a diode as a detector. the transceiver installation affects on the response and sensitivity of the system. In accordance with the detector output, several targets are easily classified by amplitudes on the scope. The traffic flow, i.e., target movement which is analyzed by the amplitude method, is shown through the scope and indicates it on the digital counter. The best efficiency for the amplitude analysis can be attained through use of an antenna having the highest sensitivity.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2001.12a
• /
• pp.99-102
• /
• 2001

It has well known that the congestion of traffic and it's distribution. There are very important problems in the traffic control systems. In this paper, we will purpose an ITFS(Intelligent Traffic Forecasting System) which can determine the car classes and transport them to ITS(Intelligent Traffic control System). The system will be used the Inductive Loop Detector(ILD)and the Fuzzy logic and shown the effectiveness by the computer simulation.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.221-227
• /
• 2008

This study identifies the relationship between traffic data quality obtained from loop detectors and their location. Traffic data basically shows traffic flow conditions and thus, these information can be used as inputs for various transportation management strategies. Out study presents how to determine optimal downstream detector location on merging area in order to enhance the effects of ramp metering strategies. Microscopic simulation model, PARAMICS, is used as the main analytical tool. Assuming that detector location relies heavily on traffic flow characteristics in each roadway segment, we perform statistical analysis to identify homogeneous traffic conditions on merging area.