• 한국항해항만학회지
• /
• 제33권1호
• /
• pp.1-7
• /
• 2009

항행속력규제는 통항안전성을 확보하기 위한 중요한 요소로서, 지금까지는 최고속력규제에 대하여만 연구 검토되어지고 있다. 최근 우리나라 항만에서는 중량물 운반용 예부선 등을 포함한 저속 항행선박으로 인하여 선박운항자의 위험부담감은 점점 증가하고 있다. 본 연구에서는 이러한 저속선박에 대한 최저속력 규제의 필요여부와 교통용량별 적정 최저속력을 산출하여 제안하였다. 이 연구의 구체적인 결과는 다음과 같다. (1) 시간당 통항척수가 5척의 경우에 최저속력을 5kts 이상으로 설정하면 속력규제 효과가 높다 (2) 시간당 통항척수가 10척 이상의 경우에 최저속력을 7kts로 설정하여야 속력규제 효과가 다소 있다 (3) 반면에, 통항척수가 많은 해역에서는 상대속력차가 적은 선박이 다수 발생하여, 선박 간 좁은 이격거리로 장시간 항행하여야 하므로 최저속력규제의 효과가 없는 것으로 판단된다.

• 한국수산과학회지
• /
• 제4권3_4호
• /
• pp.79-91
• /
• 1971

자루 입구의 둘레가 력자망지 150골(75m)되는 권현망어구의 $\frac{1}{10}$ 크기의 모형을 제작하여, 어구의 유분저항과 린망중의 그물꼴에 관하여 실험한 결과 다음과 같은 결론을 얻었다. 1. 모형 어구로부터 환산된 실물어구의 유분저항은 (R은 kg, v는 m/sec) 전저항 $$R_1=30,000\;v^{1.2}\;(0.2{\leqq}v{\leqq}1.0)$$ 자루 저항 $$R_2=16,000\;v^2\;(0.2{\leqq}v{\leqq}0.6)$$ 2. 예망중의 그물꼴은 (1) 오비기(extension wing) 발줄의 전 길이 중, 앞 끝부터 약 $70\%$ 까지는 직선상으로 깊어지며, 해저에 나란한 부분은 안쪽 약 $30\%$ 정도이다. (2) 수비(inside-wing)의 마깥 언저리는 예망속도가 0.2 m/sec이상 되면, 자루와 수비의 연결부 보다 더 뒤로 쏠려서, 어군을 자루로 유도하는 데 합리적인 형상이 아니다. 이것을 시정하기 위해서는, 수비의 깊이 방향의 코스를 $\frac{1}{2}\~\frac{2}{3}$ 정도로 줄이거나, 또는 그물코의 크기를 그런 정로로 줄임과 동시에, 자루 입구에서 오비기 발줄로 가는 힘줄을 넣어서 수비에는 예망장력이 적게 미치도록 하는 것이 좋다고 생각된다. (3) 앞치마(lower bosom)는 예망속도가 0.2m/sec이상 되면, 뒤끝치 들어 올려져서 수심이 깊은 어장에서는 수비에까지 유도된 어군도 이리로 해서 도피할 우려가 있다. (4) 문턱(upper bosom)의 계관 상의 경사 각도는 $35\~40^{\circ}$이다. 이것은 어군을 자루그물로 유도하게 유도하기에는 너무 크다고 보아진다. 따라서, 문턱은 좀 더길게 해서 경사 각도를 작게 하는 것이 좋다고 생각된다. (5) 자루(bag net)의 모양은 예망속도가 0.2m/sec 이상 되면, 뒤쪽이 앞쪽보다 좁아져서, 구성상 앞쪽보다 뒤쪽을 넓게한 의도가 나타나지 않는다. 따라서 자루 그물은 전체 모양이 길다란 원통형이 되게 구성하는 것이 합리적이라고 생각된다.

• 수산해양기술연구
• /
• 제42권3호
• /
• pp.148-157
• /
• 2006

A model experiment, simulation test using personal computer and real sea trial fishing were carried out to investigate the basic efficiency of bottom trawl net which can be used in the sea mount of North West Pacific, and experimental values were analyzed as the values of full-scale bottom trawl net. Hydrodynamic resistance for the full-scale trawl net according to the Koyama equation was 2.1 times higher than that of simulation and 2.4 times higher than that of model experiment at the average towing velocity. At the 3.5kt's of towing speed, net width of the full-scale trawl net was 2.5% smaller than that of simulation and 8.2% larger than that of model experiment. On the fishing experiment of the full-scale trawl net for the 3.5kt's of average towing speed, average net height of A group(same direction with external force) was 423.5% higher than that of model experiment and 457.1% higher than that of simulation and that of B group(opposite direction with external force) were 283.8% and 306.3% higher than in case of model experiment and Simulation respectively. Net mouth of the full-scale trawl net was 338.1-504.6% higher than those of model experiment and simulation in A group, and 525.2-745.3% higher in B group.

• 수산해양기술연구
• /
• 제49권3호
• /
• pp.301-310
• /
• 2013

To suggest a standard concerning with the arrangement of bridge equipment, the authors conducted the video observations with 3CCD (charge coupled device) cameras installed on the ceil of the bridge for monitoring the working activities of two bridge teams (the skipper/mate1 and the skipper/mate2) in a Korean coastal large trawler(gross tonnage: 139) for five days from July 30th. 2010 and analyzed of the data. Work elements coded by the work activities were input on the sheet of work analysis by the time unit of 1 sec according to the time occurred. A single work element among the work activities for every 5 minutes was denoted as the number of occurrence. The frequency of equipment usage was limited only in the usage of the equipment. In the case of the navigation and the towing net two ranks were integrated and analyzed. On the other hand, in the case of the casting net and the hauling net, two processes were integrated to as one and then analyzed separately as two ranks. As the results, 15 elements of work was carried out between two bridge teams for the observation; lookout, radar, GPS plotter, fish finder, net monitor, fishing deck, RPM indicator, rudder angle indicator, compass card, for maneuver; steering, ship speed control, trawl winch operation and external communications, paper works and others. It was found that the work load of the skipper per 5 minutes accordance with the navigation, the casting net, the towing net and the hauling net are 20.5 times, 11.9 times, 38.0 times and 9.5 times respectively, the mates are 65.2 times, 66.5 times, 85.7 times and 59.1 times respectively. The radar was shown the highest frequency of the equipment usage and the next was the fish finder, the GPS plotter and the external communications in the case of the navigation. In the case of the towing net the frequency of usage was high the ranking as the radar, the net monitor, the fish finder, the GPS plotter, the steering system and the external communications. In the case of the integrated process both of the casting and hauling net the trawl winch was shown the highest frequency to the skipper and the next was the GPS plotter and the radar, and the steering system was shown the highest frequency to the mate and the next was the radar, the ship speed control system, the GPS plotter, the net monitor and the fish finder.

• 수산해양기술연구
• /
• 제43권1호
• /
• pp.49-61
• /
• 2007

Otter boards in the trawl are the one of essential equipments for the net mouth to be spread to the horizontal direction. Its performance should be considered in the light of the spreading force to the drag and the stability of towing in the water. Up to the present, studies of the otter boards have focused mainly on the drag and lift force, but not on the stability of otter boards movement in 3 dimensional space. In this study, the otter board is regarded as a rigid body, which has six degrees of freedom motion in three dimensional coordinate system. The forces acting on the otter boards are the underwater weight, the resistance of drag and spread forces and the tension on the warps and otter pendants. The equations of forces were derived and substituted into the governing equations of 6 degrees of freedom motion, then the second order of differential equations to the otter boards were established. For the stable numerical integration of this system, Backward Euler one of implicit methods was used. From the results of the numerical calculation, graphic simulation was carried out. The simulations were conducted for 3 types of otter boards having same area with different aspect ratio(${\lambda}=0.5,\;1.0,\;1.5$). The tested gear was mid-water trawl and the towing speed was 4k't. The length of warp was 350m and all conditions were same to each otter board. The results of this study are like this; First, the otter boards of ${\lambda}=1.0$ showed the longest spread distance, and the ${\lambda}=0.5$ showed the shorted spread distance. Second, the otter boards of ${\lambda}=1.0$ and 1.5 showed the upright at the towing speed of 4k't, but the one of ${\lambda}=0.5$ heeled outside. Third, the yawing angles of three otter boards were similar after 100 seconds with the small oscillation. Fourth, it was revealed that the net height and width are affected by the characteristics of otter boards such as the lift coefficient.

• 수산해양기술연구
• /
• 제55권1호
• /
• pp.7-19
• /
• 2019

This study was conducted in order to improve opening efficiency of the miniaturized small-scale net for anchovy boat seine gear to reduce the fleet size. Field experiment was performed to observe geometry of nets by catcher boats. When the distance between the two ships was 150, 300 and 450 m and the speed of towing nets was 0.6, 0.9, and 1.2 kt, the vertical opening and actual opening of each part of the miniaturized small-scale net was as follows: the front part of the wing net, 6.8-9.5 m, 45-63%; the middle part of the wing net, 16.1-30.7 m, 34-65%; the entrance of the inside wing net, 21.6-41.2 m, 44-84%; the square and bosom, 17.4-34.0 m, 38-75%; the entrance of the body net, 16.5-29.4 m, 36-64%; the entrance of the bag net, 14.5-21.9 m, 70-106%; the flapper, 6.7-7.7 m, 81-83%, and the end of the bag net, 8.6-10.9 m, 64-81%. The tension of towing nets was measured to be 2,734-6,812 kg approximately, which indicates that the fleet can tow nets with 350 hp, the standard engine horse power. The fishing operation time was shortened comparing to existent net with the large-scale buoy attachment operation. It was also possible to operate the ship without fish detecting boat.

• 한국해양공학회지
• /
• 제15권2호
• /
• pp.1-5
• /
• 2001

A study on the new active type oil-water separation system including the oil-water separation system of magnetic film was carried out. Separation system is composed of several active types of circulating oil separation steps and one magnetic film separation step at final stage. At the magnetic separation step, ferrofluid easily forms a weak magnetic mixture with oil, which is from the water by magnetic field gradient. The vessel has been designed to run at the maximum speed of 25 knots. And two typical forms of SWATH and Catamaran have been studied as a new type of oil recovery vessel.

• 대한조선학회지
• /
• 제19권4호
• /
• pp.61-70
• /
• 1982

The hydrodynamic effects on resistance and propulsive performance were studied by using the data from model test and full scale speed trials. A series of model tests on 3 geosims for a 60,000 DWT Bulk Carrier was conducted at KIMM's Ship Experimental Towing Tank and the results analyzed by 1978 ITTC Performance Prediction Method show the correlation between 3 geosim models. Also powering data of full scale speed trials were analyzed by the newly developed computer program and the correlation analysis between ship and model was studied.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.256-273
• /
• 2019

Nowadays interceptors have been widely used in a vast range of high-speed crafts. In this study, the results of interceptor adeptness experiments made in Istanbul Technical University's Towing Tank are unveiled. The model was tested through three transverse locations of interceptors with six different deployment depths. For three locations, the interceptor was positioned transverse on the aft; close to chine, in the middle and close to the keel. The fourth interceptor was a full length of 13.00% LWL. The results show a significant drag reduction in benefits of 1.50%-11.30% for Fn 0.58-1.19 and the trim reduction was observed in between 1.60 and $4.70^{\circ}$. Besides, one of the most significant conclusions indicates that the effect of the interceptor decreases from keel to chine for the same blade deployment heights so the blades should be controlled separately at least in three parts from keel to chine area, if operable.

• 한국해양공학회지
• /
• 제25권1호
• /
• pp.27-31
• /
• 2011

The previously developed method of estimating the propulsion performance of a UUV was applied to the high speed UUV, which is propelled by commercial thrusters. The thrusters were selected with an overdesign mentality; in other words, their capacities were excessive. At that point, the designer's concern was focused on a question regarding at what rpm the UUV could reach the design speed. Because the developed method required thrust coefficient curve data, the researchers asked for the POW data of the thrusters from the manufacturer. From the data, the researchers extracted the thrust coefficient and estimated the rpm value of design speed for the UUV. Finally, the researchers compared the estimated value and the result from a self-propulsion test using a VPMM (Vertical planar motion mechanism) test at a towing tank in MOERI.