• 한국세라믹학회지
• /
• 제34권11호
• /
• pp.1129-1138
• /
• 1997

Al2O3/20 vol%YAG composite containing equiaxed grains and Al2O3/20 vol%LaAl11O18 composite containing elongated grains were fabricated using Al2O3-Y2O3 composition and Al2O3-La2O3 composition, respectively, by hot-pressing. In order to investigate the influence of microstructural control of second phase on toughening effect of toughened ceramic composites, AE (acoustic emission) measurements have been coupled with fracture toughness experiments(SENB and SEPB method). A separation of the fracture toughness and analysis of toughening mechanism was possible using the AE technique. The fracture toughness of hot-pressed materials was estimated to be 3.2 MPam0.5 for monolithic alumina, 4.7 MPam0.5 for Al2O3/20 vol%YAG composite and 6.2 MPam0.5 for Al2O3/20 vol%LaAl11O18 composite. In monolithic Al2O3, toughening does not occur as a result of either microcracking or grain bridging, whereas, composites exhibit toughening effects by both microcracking in the frontal zone and gain bridging in the wake zone, resulting in an improvement of fracture toughness as compared with monolithic Al2O3. The fracture toughness of Al2O3/20 vol%LaAl11O18 composite is higher than that of Al2O3/20 vol%YAG composite. It may be attributed to the elongated microstructure of Al2O3/20 vol%LaAl11O18 composite, resulting relatively greater bridging effect.

• 폴리머
• /
• 제31권2호
• /
• pp.123-129
• /
• 2007

세 종류의 폴리올레핀 복합재료의 기계적인 특성과 파괴인성 메커니즘이 연구되었다. 기계적 특성을 조사하기 위해 인장 시험 및 아이조드 충격 시험이 수행되었다. 균열 선단 주위의 파손 메커니즘을 정확히 조사하기 위해 2노치-4점 굽힘 기법이 도입/적용되었다. 광학현미경과 투과형 전자현미경을 이용하여, 폴리올레핀 복합재료의 균열 선단 주변 국부적인 파괴인성 특성들이 관찰되었다. 이를 통한 구체적인 관찰은, 폴리올레핀 복합재료의 균열선단 주변에 전단밴딩, 크레이즈, 입자-수지간 분리, 고무입자의 캐비테이션, 크랙 휭 및 크랙 분기 등과 같은 다양한 파괴인성 메커니즘들이 존재함을 보여주었다. 이러한 파괴인성 메커니즘들은 아이조드 충격 시험에서 보여진 파괴인성 값의 증가에 대한 실질적인 원인으로 보여진다. 본 연구를 바탕으로, 2노치-4점 굽힘 기법은 폴리올레핀 복합재료의 파괴 거동과 그와 관련된 파괴인성 메커니즘을 기술할 수 있는 충분한 정보를 제공하였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.106-109
• /
• 2001

In this work, we investigate the toughening mechanism of the rubber-modified epoxy resin. The fracture toughness($K_{IC}$) is measured using CT specimens for three kinds of rubber-modified epoxy resin with different rubber content. The damage zone and rubber particles around a crack tip of a damaged specimen just before fracture are observed by a polarization microscope and an atomic force microscope(AFM). Both the fracture energy($G_{IC}$) and the size of damage zone increase with the rubber content below l5wt%. The size of the rubber particles can be qualitatively correlated with the $G_{IC}$ and the size of damage zone. The cavitation of the rubber particles inside the damage zone is observed, which is expected to be main toughening mechanism by rubber particles. the stress which causes the cavitation of rubber particles is estimated by the Dugdale model.

• 한국세라믹학회지
• /
• 제35권12호
• /
• pp.1266-1273
• /
• 1998

Al2O3/(5~20vol%)LaAl11O18 composites in which the second phase was dispersed with a elongated grain shape were fabricated using Al2O3 and La2O3 composition by hot-pressing. In order investigate the in-fluence of LaAl11O18 on the toughening of LaAl11O18 on the toughening of Al2O3 matrix composites AE(acoustic emission) analysis was con-ducted together with an evaluation of fracture toughness using of SEPB technique. The degree of AE events occurred in composites were more than those in monolithic alumina. The occurrences of AE event increased with increasing the amount of LaAl11O18 phase in the Al2O3/LaAl11O18 composite is two times higher compared to monolithic alu-mina. The main toughening mechanism was attributed to the bridging of LaAl11O18 grains at tip of pro-pagating crack.

• 한국세라믹학회지
• /
• 제33권4호
• /
• pp.464-470
• /
• 1996

Toughening mechanism of boron carbide ceramics by the addition of titanium boride was investigated. Speci-men was prepared by hot pressing of boron carbide with upto 30vol% of titanium boride particulates. Toughness of boron carbide ceramics was increased from 4.7 MPa m1/2 to 6.3 MPa m1/2 with 15 vol% TiB2 addition. But further increase of TiB2 content results in slow decrease of toughness. From microstructure evaluation and crack propagation behavior it is concluded that the major toughening mechanism is crack deflection pheno-mena.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.290-290
• /
• 2006

The toughening mechanisms of polypropylene (PP) containing 9.2 vol % of calcium carbonate ($CaCO_{3}$) nanoparticles were investigated using optical microscopy and transmission electron microscopy. Double-notch four-point bending (DN-4PB) Charpy impact specimens were utilized to study the fracture mechanism(s) responsible for the observed toughening effect. A detailed investigation reveals that the $CaCO_{3}$ nanoparticles act as stress concentrators to initiate massive crazes, followed by shear banding in PP matrix. These toughening mechanisms are responsible for the observed improved impact strength.

• 한국재료학회지
• /
• 제9권2호
• /
• pp.132-138
• /
• 1999

In order to investigate the toughening characteristic by microcrack formation in ceramic composites, $Al_2$O$_3$/(0~20)vol% YAG composites containing equiaxed second grains were fabricated using$ Al_2$$O_3$ during hot-pressing. AE(acoustic emission) measurements have been coupled with fracture toughness experiments of SENB method, to evaluate the microcrack formation and the improvement in fracture toughness of ceramic composites. Formation of microcrack was detected by Ae. The generation of AE events increased with increasing of load when load was applied at specimen. The AE events are generated mainly around at maximum load. Specially, the detected AE evetns of composites are many as compared with monolithic $Al_2$$O_3$. Fracture toughness of composites was improved than that of monolithic alumina. $Al_2$O$_3$/YAG composites exhibit main toughening effects by microcracking, results from mutual coalesence of microcracks being generated under applied load. However, there are few toughening mechanism like microcracking in monolithic alumina.

• 콘크리트학회지
• /
• 제6권6호
• /
• pp.151-158
• /
• 1994

본 연구에서는 수경성 시멘트 경화체의 구조적 결함인 휨강도를 향상시키시 위해 보통 포틀랜드 시멘트비를 0.1로 하여 혼합수량을 줄이고 수용성 고분자 물질인 Hydroxy Propy Methyl Cellulose(HPMC)를 첨가하여 시멘트입자의 윤활작용에 따른 균일한 분산효과와 결합효과를 얻도록 하였으며, twin roll mill로 혼련 성형하여 치밀하고 균일한 경화제 시편을 제조하였다. 이러한 고강도 시멘트 경화체의 휨강도는 약 96MPa, 탄성계수는 60GPa로 우수한 특성을 나타내었다. 고강도 시멘트의 고강도화 기구는 100${\mu}m$ 이상의 큰 기공제거 및 균열성장경로인 모세관 기공의 감소, 미수화 시멘트의 증가로 인한 탄성계수의 증가와 crack toughening(입자 가교, 고분자 섬유 가교, frictional interlocking)에 의한 파괴 인성의 향상 때문인 것으로 판단된다.

• 공업화학
• /
• 제5권2호
• /
• pp.215-222
• /
• 1994

Chlorosulfonated polyethylene(CSM)은 수지의 toughness modifier로서 사용할 수 있다. CSM는 산소와 오존에 대해서 저항성이 클 뿐 아니라 가교 가능한 기능기인 sulfonyl chloride를 가졌기 때문에 금속 산화물에 의해 가교 될 수 있다. Polyvlnylchloride(PVC)는 물성이 좋을 뿐 아니라 값이 싼 plastic이기 때문에 널리 사용되는 범용수지이나 저온에서 충격강도가 약하고 빛과 산소 그리고 오존에 의해서 분해되어 물성을 떨어뜨리는 결점이 있다. 이런 결점을 개선하고저 PVC/CSM블렌드를 연구하였다. CSM함량 10~30%에서 현저한 toughening효과를 나타내었다. CSM을 블렌드함으로써 PVC의 내후성, 내오존성 및 기계적 성질이 개선되었으며 toughening효과를 SEM을 통하여 관찰하고 확인하였다.

• The Korean Journal of Ceramics
• /
• 제1권4호
• /
• pp.197-203
• /
• 1995

Nearly fully dense PZT samples both with tetragonal and with morphotropic phase boundary compositions were prepared by the conventional powder processing and sintering. A micro-indentation technique was used to evaluate the dependence of fracture toughness on remanent polarization, crack length and the direction of crack propagation. The result shows that the toughness increases with the remanent polarization along the poling direction and decreases in the transverse direction. The dependence of toughness on the remanent polarization is neither symmetric nor linear but rather shown to be saturated quickly with the increase in remanent polariztion. R-curve behaviors are observed in both poled and unpoled samples. Sequential SEM and XRD studies on annealed, poled, ground, fractured and etched samples show that domain switching is evident as a viable toughening mechanism but might depend upon the rate of crack propagation. Grain bridging is also observed as one of the active toughening mechanisms.