• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.17-48
• /
• 1976

In analyzing the operational characteristics of a rice whitening machine, the internal radial pressure of the machine was measured using strain gage equipment. Changes in cylinder and feed screw configurations, screen type, cylinder speed and counter-pressure levels were examined to determine their impact on the quality and quantity of milled rice and the performance of the machine. The results are summarized as follows: 1. The internal radial pressure in the whitening chamber varied with the surface condition of the grain being processed. During the first or second pass through the machine, pressure was relatively low, reached a maximum after two to three passes with combinations I and II, three to six with combination III and then began to fall. 2. The pitch of the feed screw and the size of the feed gate opening which determine the rate of entry of grain into the whitening chamber, appeared to be the most important factor aff-::cting the degree of radial pressure, quality and quantity of milled rice and the efficiency of the machine. Using a feed screw with a wide pitch (4.8cm), radial pressure was relatively high and head rice recovery ratio \vere quite low. In this case capacity and machine effic\ulcorneriency were much higher than obtained when using a feed screw with a narrow pitch (2.3cm). Very significant responses in radial pressure, head rice recovery rates and machine capacity were observed with changes in cylinder speed and counter-pressure levels when using the wide pitch feed screw. 3. The characteristics of the screen which surrounds the whitening chamber had an important effect on whitening efficiency. The existence of small protuberances on the original screen resulted in significant increases in both machine capacity and efficiency but without a significant decrease in head rice recovery or development of excessive radial pressure. Further work is required to determine the effects of screen surface conditions and the shape of the cylinderical steel roller on the rate of bran removal, machine efficiency and recovery rates. The size of the slotted perforations 0:1 the screen affects total milled rice recovery. The opening size on the original screen was fabricated to accommodate the round shape of Japonica rice varieties but was not suitable for the more slender Indica type. Milling Indica varieties with this screen resulted in a reduction in total milled rice recovery. 4. An increase in cylinder speed from 380 to 820 rpm produced a positive effect on head rice recovery for all machine combinations at every level of counter-pressure used in the tests. Head rice recovery was considerably lower at 380rpm using a wide screw pitch when compared to the results obtained at speeds from 600 to 820 r.p.m. The effects of cylinder speed On radial pressure, capacity and machine efficiency showed contrasting results, depending on the width of the feed screw pitch. With a narrow feed screw pitch (2.3cm), a direct proportional relationship was observed bet\ulcornerween cylinder speed and both radial pressure and machine efficiency. In contrast, using a 4.8 centimeter pitch feed roller produced a series of inverse relationships between the above variables. Based on the results of this study it is recommended when milling Indica type long grain rice varieties that the cylinder speed of the original machine be increased from 500-600 rmp up to a minimum of 800 rpm to obtain a greater abrasive effect between the grain and the screen. The pitch of the feed screw should be also reduced to decr\ulcornerease the level of internal radial pressure and to obtain higher machine efficiency and increased quality of milled rice with increased cylinder speeds. Further study on the interaction between cylinder speed and feed screw pitch is recommended. 5. An increase in the counter pressure level produced a negative effect On the head rice recovery with an increase in radial pressure, capacity, and machine efficiency over all combinations and at every level of cylinder speed. 6. Head rice recovery rates were conditioned primarily by the pressure inside the whitening chamber. According to the empirical cha racteristics curve developed in this study, the relationships of head rice recovery ($Y_h$) and machine capacity ($Y_c$/TEX>) to internal radial pressure ($X_p$) followed an inverse quadratic function and a linear function respectively: $$Y_h^\Delta=\frac{1}{{1.4383-0.2951X_p^\ast+0.1425X_p^{\ast\ast}}^2} , (R^2=0.98)$$ $$Y_c^\Delta=-305.83+374.37X_p^{\ast\ast}, (R^2=0.88)$$ The correlation between capacity and power consumption per unit of brown rice expressed in the following exponential function: $$Y_c^\Delta=1.63Y_c^{-0.7786^\{\ast\ast}, (R^2=0.94)$$ These relationships indicate that when radial pressure increases above a certain range (1. 6 to 2.0 kg/$cm^2$ based On the results of the experiment) head ricerecovery decrea\ulcornerses in a quadratic relation with a inear increase in capacity but without any decrease in power consump tion per unit of brown rice. On the other hand, if radial pressure is below the range shown above, power consumption increases dramatically with a lin\ulcornerear decrease in capacity but without significant increases in head rice recovery. During the operation of a given whitening machine, the optimum radial pressure range or the correct capacity range should be selected by controlling the feed rate and/or counter-pressure keeping in mind the condition of the grain, particulary the hardness. It was observed that the total number of passes is related to radial pessure level, feed rate and counter-pressure level. The higher theradial pressure the fewer num\ulcornerber of pass required but with decreased head rice recovery. In particular, when using high feed rates, the total number of passes should be increased to more than three by reducing the counter-pressure level to avoid decreaseases in head rice recovery (less than 65 percent head rice recovery on the basis of brown rice) at every cylinder speed. 7. A rapid rise in grain temperature seemed to have a close relationship with the pressure generated inside the whitening chamber and, subsequently with head rice reco\ulcornervery rates. The higher the rate of increase, the lower were the resulting head rice recoveries.

• Journal of Microbiology
• /
• 제45권2호
• /
• pp.158-167
• /
• 2007

In this study, we have cloned a novel cDNA encoding for a papain-family cysteine protease from the Uni-ZAP XR cDNA library of the polychaete, Periserrula leucophryna. This gene was expressed in Escherichia coli using the T7 promoter system, and the protease was characterized after partial purification. First, the partial DNA fragment (498 bp) was amplified from the total RNA via RT-PCR using degenerated primers derived from the conserved region of cysteine protease. The full-length cDNA of cysteine protease (PLCP) was prepared via the screening of the Uni-ZAP XR cDNA library using the $^{32}P-labeled$ partial DNA fragment. As a result, the PLCP gene was determined to consist of a 2591 bp nucleotide sequence (CDS: 173-1024 bp) which encodes for a 283-amino acid polypeptide, which is itself composed of an 59-residue signal sequence, a 6-residue propeptide, a 218-residue mature protein, and a long 3'-noncoding region encompassing 1564 bp. The predicted molecular weights of the preproprotein and the mature protein were calculated as 31.8 kDa and 25 kDa, respectively. The results of sequence analysis and alignment revealed a significant degree of sequence similarity with other eukaryotic cysteine proteases, including the conserved catalytic triad of the $Cys^{90},\;His^{226},\;and\;Asn^{250}$ residues which characterize the C1 family of papain-like cysteine protease. The nucleotide and amino acid sequences of the novel gene were deposited into the GenBank database under the accession numbers, AY390282 and AAR27011, respectively. The results of Northern blot analysis revealed the 2.5 kb size of the transcript and ubiquitous expression throughout the entirety of the body, head, gut, and skin, which suggested that the PLCP may be grouped within the cathepsin F-like proteases. The region encoding for the mature form of the protease was then subcloned into the pT7-7 expression vector following PCR amplification using the designed primers, including the initiation and termination codons. The recombinant cysteine proteases were generated in a range of 6.3 % to 12.5 % of the total cell proteins in the E. coli BL21(DE3) strain for 8 transformants. The results of SDS-PAGE and Western blot analysis indicated that a cysteine protease of approximately 25 kDa (mature form) was generated. The optimal pH and temperature of the enzyme were determined to be approximately 9.5 and $35^{\circ}C$, respectively, thereby indicating that the cysteine protease is a member of the alkaline protease group. The evaluation of substrate specificity indicated that the purified protease was more active towards Arg-X or Lys-X and did not efficiently cleave the substrates with non-polar amino acids at the P1 site. The PLCP evidenced fibrinolytic activity on the plasminogen-free fibrin plate test.

• 생명과학회지
• /
• 제27권10호
• /
• pp.1152-1160
• /
• 2017

단세포 녹조류 균주를 경상북도 울릉군 울릉도 거북바위 주변 조수웅덩이로부터 순수분리하여 형태적, 분자적, 및 생화학적 특성을 분석한 결과 옥세노클로렐라 프로토테코이드에 속하는 것으로 밝혀졌다. 본 종은 현재까지 한국에서 공식 기록이 없는 미기록종으로 옥세노클로렐라 프로토테코이드 MM0011 균주라고 명명하였으며, 생장, 지질/광합성 색소 조성 및 바이오매스 특성에 대해 조사를 실시하였다. 분리균주는 광범위한 온도($5-35^{\circ}C$)에서 생장할 수 있었으며 1.5 M 염화나트륨 농도까지 생존할 수 있었다. 가스크로마토그래프/질량분석기를 이용한 분석 결과, 본 균주에는 영양적으로 중요한 불포화지방산이 풍부한 것으로 나타났으며, 특히 리놀네산(27.6%) 및 알파 리놀렌산(37.2%)이 주요 지방산 성분으로 확인되었다. 따라서 본 토착 미세조류 균주는 어유 또는 식물성유를 대체할 수 있는 잠재적인 오메가-3 및 오메가-6 불포화지방산 원료가 될 수 있을 것으로 사료된다. 또한, 고부가가치 항산화 물질인 루테인이 보조색소로서 본 균주에 의해 생합성 되는 것으로 밝혀졌다. 일반성분분석 결과 MM0011 균주의 휘발성물질 함량은 85.6%였으며, 원소분석 결과 총 발열량은 $20.3MJ\;kg^{-1}$으로 나타났다. 또한 배지로부터 40.5%의 전질소와 27.9%의 전인을 각각 제거할 수 있어 향후 바이오연료 원료물질 생산과 오 폐수처리를 연계할 수 있는 가능성 역시 제시하였다. 추가적으로 MM0011 바이오매스는 높은 단백질 함량(51.4%)을 갖고 있어 우수한 동물사료의 원료가 될 수 있는 가능성도 보여주고 있다. 따라서, 본 균주는 미세조류 기반 생화학 물질 생산 및 바이오매스 원료로서 상업적인 이용 가능성이 높음을 시사한다.

• 한국균학회지
• /
• 제37권1호
• /
• pp.80-85
• /
• 2009

신품종 개발을 위한 예비조사로써 본 연구는 국립산림과학원에서 보존중인 노루궁뎅이류의 균주를 이용하여 균사생장을 위한 최적온도, 신갈나무에 톱밥재배, 황산화 활성물질인 ergothioneine와 polyphenols에 대해 조사하였다. 노루궁뎅이의 균사생장 최적온도는 $20^{\circ}C$에서 KFRI 842, $25^{\circ}C$에서 5개 균주(KFRI 507, 508, 509, 843, 845), $30^{\circ}C$에서 2균주(KFRI 582, 844) 이었다. 산호침버섯의 균사생장 최적온도는 $25^{\circ}C$ 이었다. 노루궁뎅이류 9개 균주중 4개(KFRI 508, 843, 844, 713)는 $25^{\circ}C$에서 20일내에 직경 85 mm의 페트리디쉬 PDA 배지를 채웠다. 그리고 나머지 균주들은 페트리디쉬를 채우는데 더 많은 시간이 필요하였다. 노루궁뎅이의 버섯 생산량은 $149{\sim}205$ g 범위 이었고 자실체 건물율은 $7{\sim}9%$ 이었다. 산호침버섯은 261 g 이었고 건물율은 10% 이었다. 노루궁뎅이의 ergothioneine과 polyphenols는 $1.6{\sim}3.7$ mg/g과 $5.9{\sim}7.8$ mg/g 이었고, 균주별로 차이가 있었다. 산호침버섯은 1.7mg/g의 ergothioneine과 3.9mg/g의 polyphenols를 함유하고 있었다. Ergothioneine과 polyphenols은 균주 간 두 성분의 함량 차이는 나타났으나 함량비는 차이가 없었다($R^2$= 0.1).

• Journal of Biosystems Engineering
• /
• 제36권4호
• /
• pp.243-251
• /
• 2011

Purpose of this study was to analyze power requirement of an agricultural tractor for baler operation. First, a power measurement system was developed and installed in a 75 kW agricultural tractor. Strain-gages with a telemetry system were used to measure torques of transmission and PTO input shafts. An engine tachometer was used to measure rotational speed of transmission and PTO input shafts. The measurement system also included pressure sensors to measure pressure of hydraulic pumps, an I/O interface to acquire the sensor signals, and an embedded system to determine power requirements. Second, field experiments were conducted at two PTO speed levels, and proportion of utilization ratio of rated engine power and power consumption of major parts (transmission input shaft, PTO input shaft, main hydraulic pump, and auxiliary hydraulic pump) were analyzed. Results of usage proportion of engine power for PTO speed level 1 and 2 were 4.1 and 2.2%, 31.5 and 16.3%, 49.6 and 59.7%, 14.4 and 20.8%, and 0.4 and 1.0%, respectively, for ratio of measured engine power to rated engine power of less than 25%, 25 ~ 50%, 50 ~ 75%, 75 ~ 100%, and greater than 100%. The results showed that the usage proportion increased in the range with the ratio of power requirement to rated engine power of over than 50% when the PTO gear was shifted from P1 to P2. Averaged engine power requirement for baling operation, tying and discharging operation, and total operation were 43.3, 37.3, and 42.0 kW and 49.0, 37.0, and 47.4 kW, respectively, for PTO speed level 1 and 2. Paired t-test showed significant difference in power consumption of engine, transmission input shaft, and PTO input shaft for different PTO speed levels. Therefore, the power consumption of engine for baler operation increased when the PTO gear was shifted from P1 to P2. It was indicated that the power requirement of tractor was affected by the PTO rotational speed for baler operation.

• Journal of Korean Neurosurgical Society
• /
• 제46권6호
• /
• pp.532-537
• /
• 2009

Objective : Recently, motion preservation has come to the forefront of emerging technologies in spine surgery. This is the important background information of the emergence of cervical arthroplasty as an alternative to arthrodesis that offers the promise of restoring normal spinal movement and reduces a kinematic strain on adjacent segments. The study was designed to evaluate early surgical outcome and radiological effects of $Bryan^{(R)}$ cervical disc prosthesis. Methods : The authors retrospectively reviewed radiographic and clinical outcomes in 52 patients who received the $Bryan^{(R)}$ Cervical Disc prosthesis, for whom follow-up data were available. Static and dynamic radiographs were measured by computer to determine the angles formed by the endplates of the natural disc preoperatively, those formed by the shells of the implanted prosthesis, the angle of functional spine unit (FSU), and the C2-7 Cobb angle. The range of motion (ROM) was also determined radiographically, whereas clinical outcomes were assessed using Odom's criteria, visual analogue pain scale (VAS) and neck disability index (NDI). Results : A total of 71 $Bryan^{(R)}$ disc were placed in 52 patients. A single-level procedure was performed in 36 patients, a two-level procedure in 13 patients, and a three-level procedure in 3. Radiographic and clinical assessments were made preoperatively. Mean follow-up duration was 29.2 months, ranging from 6 to 36 months. All of the patients were satisfied with the surgical results by Odom's criteria, and showed significant improvement by VAS and NDI score (p < 0.05). The postoperative ROM of the implanted level was preserved without significant difference from preoperative ROM of the operated level (p < 0.05). 97% of patients with a preoperative lordotic sagittal orientation of the FSU were able to maintain lordosis. The overall sagittal alignment of the cervical spine was preserved in 88.5% of cases at the final follow up. Interestingly, preoperatively kyphotic FSU resulted in lordotic FSU in 70% of patients during the late follow up, and preoperatively kyphotic overall cervical alignment resulted in lordosis in 66.6% of the patients postoperatively. Conclusion : Arthroplasty using the $Bryan^{(R)}$ disc seemed to be safe and provided encouraging clinical and radiologic outcome in our study. Although the early results are promising, this is a relatively new approach, therefore long-term follow up studies are required to prove its efficacy and its ability to prevent adjacent segment disease.

• 한국미생물·생명공학회지
• /
• 제36권4호
• /
• pp.260-267
• /
• 2008

단백질의 산업적 생산을 위해 발현벡터의 선정이 중요하지만 이용 가능한 프로모터가 극히 제한적이며 많은 경우 과발현되는 특성과 함께 불용성 응집체가 형성되는 단점을 지닌다. 따라서 다양한 생물로부터 유래된 잠재성이 큰 유전자원(metagenome)에서의 프로모터 발굴과 한정된 숙주를 해결하려는 노력이 요구된다. 선행연구에서 발굴한 metagenome 유래의 항시발현 프로모터를 이용해 대장균의 일반적인 배양조건에서 세포생리에 영향이 적은 신규 항시발현 벡터를 제작하였다. 이를 위해 예측된 프로모터 서열과 MCS를 포함하는 합성 primer를 제작한 후 PCR로 증폭해 발현벡터를 구성한 후, 프로모터 구동여부와 단백질 발현양상 등을 관찰하였다. 인위적으로 도입된 MCS에 GFP, esterase, $\beta$-glucosidase를 클로닝해 단백질 발현양과 가용성을 분석한 결과, 안정적으로 전체단백질의 $2{\sim}3%$ 정도로 발현되며 80% 이상의 높은 가용성을 지닌 단백질의 발현이 유도되는 것으로 확인되었다. 이와 같은 결과는 잠재적인 생물자원의 보고로서 metagenome의 활용가능성을 제시하고 있다. 따라서 다양한 숙주에서 작동하는 프로모터의 발굴 및 발현벡터의 제작을 시도할 경우 단백질의 생산이나 대사공학에 의한 균주개량에 유용하게 활용할 수 있을 것이다.

• Parasites, Hosts and Diseases
• /
• 제29권2호
• /
• pp.181-188
• /
• 1991

최근 전국적으로 높은 이환률을 보이고 있는 쭈쭈가무시병에 대한 방제 대책이 시급한 현실에 반해 본 질병에 대한 연구가 거의 이루어져 있지 않기 때문에 저자들은 1989년 7월부터 1950년 9월까지 9개 지역에서 숙주동물에 대한 역학적 조사를 실시하여 다음과 같은 결과를 얻었다. 1. 모두 794개의 Sherman식 live trap을 설치하여 111마리의 들쥐로 포획하여 trapping rate가 평균 14.0%이었다. 계절별로 보면 봄, 여름, 가을에 각각 11.7%, 11.2%, 12.8%이었고 겨울에는 24.0%로 가장 높았다. 포획한 111마리 중 103마리가 등줄쥐 (Apodemus agrarius)로 92.8%를 차지하여 우점종이었고, 땃쥐 (Crocidura Zasiura)가 7마리로 6.3%이었으며. 갈밭쥐 (Microtns fortis)는 1마리가 채집되어 0.9%이었다. 들쥐의 털진드기 기생률을 보면, 등줄쥐의 경우 103마리 중 84마리로 81.6%이었고, 땃쥐의 경우 7마리 중 2마리로 28.6%이었다. Chigger index는 등줄쥐의 경우 43.0개체였고 만취는 0.9개체였다. 2. 등줄쥐 혈청의 Rickettsia tsutsugamushi 항체 양성률을 보면 평균 41.8%이었는데, 조사 지역에 따라 큰 차이가 있어 고양군 도래 5리 54.9%, 고양군 고양리 20%, 고양군 원홍 2리 28.6%, 청인군 시목리 40%이었고 고양군 행신 1리, 파주군 광탄 3리 와 예산군 덕산리에서는 모두 음성이었다. 땃쥐의 경우는 7마리 모두 음성이었다. 동일 장소에서의 등줄쥐 혈청의 R. tsutsugamushi 항체 양성률의 계절적 변동은 11월부터 3웜까지는 평균 75.8%이었는데 4일에는 30.3%로 감소하였고 5월부터 8월에 걸쳐 평균 13.3%로 크게 감소하였다. 조사한 모든 양성 혈청의 항체가를 보면 Karp, Gilliam및 Kato 주에 대해 서로 교차반응을 나타냈는데 Karp주와 Kato 주 간에 보다 강한 교차반응을 보였다. 3. 총 94마리의 등줄쥐로부터 마우스 복강접종법과 간접 면역형광법으로 R. tsutsugamushl치 분리를 시도한 바 3마리에서 분리되어 감염률은 3.2%이었다.

• 한국강구조학회 논문집
• /
• 제22권4호
• /
• pp.389-398
• /
• 2010

교량용 HSB 고성능 강재를 적용한 정모멘트부 강합성거더의 휨저항강도를 모멘트-곡률 해석법으로 산정하고 일반 강재에 적용되는 AASHTO LRFD 조밀단면 휨저항강도 설계식에 의한 휨저항강도와 비교하여 기존 설계식의 적용성을 검토하였다. 다양한 연성특성을 갖는 2,391개 단면을 임의추출법으로 선정하고 재료 비선형 모멘트-곡률 해석 프로그램을 이용하여 이들 단면에 대한 휨저항강도를 구하였다. 합성단면을 구성하는 콘크리트 재료는 CEB-FIP 모델로, HSB600 및 HSB800 강재는 탄소성-변형경화 재료로 모델링하였다. HSB 강재를 적용한 강합성거더 단면의 연성비와 콘크리트 바닥판의 압축강도에 따른 휨저항강도 특성을 분석하고 SM520-TMC 일반 강재를 적용한 경우와 휨저항강도를 비교하였다. 2,391개의 HSB600 강합성거더 단면의 휨저항강도를 분석한 결과, 기존 LRFD 휨저항강도 설계식을 적용할 수 있는 것으로 분석되었다. 반면에, HSB800 강재를 적용한 강합성거더의 경우에는 기존 LRFD 조밀단면 휨저항강도 설계식은 비안전측으로 평가되었으며, HSB800 강합성거더의 모멘트-곡률해석 결과에 근거한 새로운 정모멘트부 휨저항강도 산정식을 제안하였다.

• 한국식품과학회지
• /
• 제31권3호
• /
• pp.788-793
• /
• 1999

본 연구에서는 오염된 무균포장밥으로부터 미생물의 분리 동정을 실시하고 AESS의 살균효과를 측정하였으며, 이를 취반수로 이용하여 취반미의 pH를 저하시킨 후 오염된 미생물의 사멸 및 생육억제 효과를 검토하였다. 오염된 3종의 시료로부터 총 6주의 오염미생물을 분리하여 생리화학적 방법에 의하여 5주의 Bacillus subtilis와 1주의 B. cereus로 동정하였다. 이 결과는 지방산 분석법에 의한 미생물동정기를 사용하여 확인하였다. AESS의 살균효과는 0.1% NaOCl 및 70% ethanol 용액의 그것과 유사하거나 보다 우수한 것으로 나타났으며, Bacillus spp.를 제외한 다른 시험미생물들은 5초간의 노출로 모두 사멸하였다. Bacillus spp.에 대해서는 AESS가 NaOCl이나 ethanole보다 우수한 살균 또는 성장 억제효과를 갖는 것으로 나타났으며, 5분간의 노출로 모두 사멸하였거나 성장 억제되었다. 또한 AESS를 취반수로 사용하면 pH $3.6{\sim}4.3$ 범위의 취반미를 얻을 수 있었으며, 제조된 밥의 pH는 저장기간 중 거의 변화를 보이지 않았다. 여기에 오염된 무균포장밥으로부터 분리된 Bacillus 균현탁액을 조제하여 접종 밀봉하고 $37^{\circ}C$에서 2주간 저장한 결과 수도수로 제조된 밥에서는 정상적인 성장을 나타냈으나, AESS로 제조된 밥에서는 오염 미생물들의 생육이 완전히 억제되었다.