• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.156-159
• /
• 2005

The outer race of CV(constant velocity) joint is an important load-supporting automotive put that transmits torque between the transmission gear box and driving wheel. The outer race is difficult to forge because its shape is very complicated and the required dimensional tolerances are very small. To guarantee the dimensional accuracy of the forged CV Joint, the quick and precise measurement is required to increase the inspection speed of forged products. Therefore in this study, PP(Pre-Position) Device to decrease the inspection time of measuring system has been developed to cope with forging cycle time. The measured inspection time confirms that the PPD is very effective in decreasing inspection time.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.160-163
• /
• 2005

The cute. race of CV(constant velocity) Joint is an important load-supporting automotive part, which transmits torque between the transmission gear box and driving wheel. The outer race is difficult to forge because its shape is very complicated and the required dimensional tolerances are very small. The forged CV Joint investigated in this study has six inner ball grooves requiring high operational accuracy. Therefore, the precise measurement of forged CV Joint is very important to guarantee the sound operation without noise and abnormal wear. In this study, unique in-situ measuring system designed specifically to measure the dimensional accuracy of six inner ball grooves of CV joint has been developed and implemented in shop environments. Newly developed system shows high measurement accuracy with simple operational sequence.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.53-57
• /
• 2001

In the industrial motor drive system which is composed of a motor and load connected with a flexible shaft, a torsional vibration is often generated because of the elastic elements in torque transmission. To solve this problem, the two degrees of freedom $H_{\infty}$ controller was designed. But it is difficult to realize that controller. In this paper, $H_{\infty}$ control of 2-mass system using partial state feedback and resonance ratio control is proposed. Proposed controller has simple structure but satisfies the attenuation of disturbances and vibrations.

• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.73-76
• /
• 2001

This paper presents a new systematic contingency selection, screening and ranking method for on-line transient security assessment. Transient stability of a particular generator is influenced most by fault near it. Fault at the transmission lines adjacent to the generators are selected as contingency. Two screening methods are developed using the sensitivity of modal synchronizing torque coefficient and computing an approximate critical clearing time(CCT) without time simulation. The first method, which considers only synchronizing power, may mislead in some cases since it does not consider the acceleration power. The approximate CCT method, which consider both the acceleration and deceleration power, worked well. Finally the Single Machine Equivalent(SIME) method is implemented using IPLAN of PSS/E for detailed stability analysis.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1133-1135
• /
• 2000

In the industrial motor drive system which is composed of a motor and load connected with a flexible shaft, a torsional vibration is often generated because of the elastic elements in torque transmission. To solve this problem, the two-degrees-of-freedom $H_{\infty}$ controller was designed. But it is difficult to realize that controller. In this paper, a new partial state feedback $H_{\infty}$ controller with resonance ratio control is proposed. Proposed controller has simple structure but satisfies the attenuation of disturbances and vibrations.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.5
• /
• pp.24-33
• /
• 2003

This study proposed a technique for inverse problem, linear approximation of contact position and loading in single and double meshing of transmission contact element using 2-dimension model considered near the tooth by root stress. Determination of root stress is carried out far the gear tooth by finite element method and boundary element method. Boundary element discretization near contact point is carefully performed to keep high computational accuracy. The predicted results of boundary element method are good accordance with that of finite element method.

• Proceedings of the KSR Conference
• /
• 2003.05a
• /
• pp.554-560
• /
• 2003

The transmission systems of high speed train serve in the severe condition compared with those of other trains, namely, they have to transmit high power to run with high speed and they have to make maximum use of the limited space. To clarify the capability of reduction gear unit for Korea High Speed Train, torque and temperature, vibration on the reduction gear unit were measured and test data were analyzed. This paper reports test methods and test results that performed to verify reliability of reduction gear unit during running test of Korea High Speed Train. It is confirmed from these results that the performance of reduction gear unit has not any problem.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.99-104
• /
• 2005

The CARB in USA has demanded OBD functions that detect any deterioration of performance of OTS as well as a simple defect of OTS which can affect emission to meet the reinforced emission regulation. In this paper, OTS plausibility monitoring functions to meet the demand from CARB are discussed. The output from OTS is used for the diagnostics of the torque converter clutch stuck and the gear ratio synchronous error. It is possible to diagnose the abnormality of OTS function by considering the oil temperature characteristics which changes according to the driving status of vehicles. In result, the OBD regulations of the CARB can be satisfied obligating car manufacturer to detect any problems in OTS functions which can affect emissions.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.12
• /
• pp.1718-1723
• /
• 2015

The diameter of the rotor of 2MW wind turbine is being developed by a number of companies with more than 80m, reliability and economic efficiency of the wind power generator has been improved. The need for large-scale wind turbine with excellent economy has been attracting attention because the new orders and the location of the wind turbine market has reached a limit. Technology development for enlargement of wind turbine is possible not only the improvement of energy efficiency but also reduce the construction costs per unit capacity. However, mechanical gearboxes used in wind generators have problems of wear, damage, need for lubrication oil and maintenance. Therefore, we want to configure the gearbox of a large-scale wind turbine using a magnetic gear in order to solve these problems of mechanical gearbox.

• International Journal of Automotive Technology
• /
• v.8 no.5
• /
• pp.599-603
• /
• 2007

An efficient optimum design process has been developed and applied to systematically design a lock-up clutch system for a torque converter used in an automatic transmission. A simulated annealing algorithm was applied to determine the parameters of the compressive helical damper springs in the clutch. The determination of the number, location, a number of turns, and deflection of damper springs plays an important role in reducing vibration and noise in the lock-up system. Next, FE-based shape optimization was coded to find the shape of the clutch disk that would satisfy the strength, noise and vibration requirements. Using the optimum code, parametric studies were performed to see how spring diameters and frequencies of clutch systems changed as the damper spring traveling angles and the torques were varied. Based on the optimum results, five different designs for clutches with different springs were fabricated and vibration analyses and tests were conducted to validate the accuracy of the proposed method. Results from the two methods show a good correlation.