• Bulletin of the Korean Chemical Society
• /
• v.33 no.2
• /
• pp.541-548
• /
• 2012

New candidates composed of anthracene and 4-alkylethynylbenzene end-capped oligomers for OTFTs were synthesized under Sonogashira coupling reaction conditions. All oligomers were characterized by FT-IR, mass, UV-visible, and PL emission spectrum analyses, cyclic voltammetry (CV), differential scanning calorimetry (DSC), thermal gravimetric analysis (TGA), $^1H$-NMR, and $^{13}C$-NMR. Investigation of their physical properties showed that the oligomers had high oxidation potential and thermal stability. Thin films of DHPEAnt and DDPEAnt were characterized by spin coating them onto Si/$SiO_2$ to fabricate top-contact OTFTs. The devices prepared using DHPEAnt and DDPEAnt showed hole field-effect mobilities of $4.0{\times}10^{-3}cm^2$/Vs and $2.0{\times}10^{-3}cm^2$/Vs, respectively, for solution-processed OTFTs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.180-180
• /
• 2015

Solution processed Resistive random access memory (ReRAM)은 간단한 공정 과정, 고집적도, 저렴한 가격, 대면적화 플라즈마 데미지 최소화 등의 장점으로 차세대 비휘발성 메모리로 써 많은 관심을 받고 있으며, 주로 high-k 물질인 HfOx, TiOx, ZnO 가 이용 된다. IGZO와 ZTO와 같은 산화물 반도체는 높은 이동도, 대면적화, 넓은 밴드갭으로 인하여 투명한 장점으로 LCDs (Liquid crystal displays)에 이용 가능하며, 최근에는 IGZO와 ZTO에서 Resistive Switching (RS) 특성을 확인한 논문이 보고되면서 IGZO와 ZTO를 ReRAM의 switching medium와 TFT의 active material로써 동시에 활용하는 것에 많은 관심을 받고 있다. 이와 같은 산화물 반도체는 flat panel display 회로에 TFT와 ReRAM의 active layer로써 집적가능 하며 systems-on-panels (SOP)에 적용 가능하다. 하지만 IGZO 보다는 ZTO가 In과 Ga을 포함하지 않기 때문에 저렴하다. 그러므로 IGZO를 대신하는 물질로 ZTO가 각광 받고 있다. 본 실험에서는 ZTO film에 Al을 doping하여 메모리 특성을 평가하였다. 실험 방법으로는 p-type Si에 습식산화를 통하여 SiO2를 300 nm 성장시킨 기판을 사용하였다. 그리고 Electron beam evaporator를 이용하여 Ti를 10 nm, Pt를 100 nm 증착 한다. 용액은 Zn와 Tin의 비율을 1:1로 고정한 후 Al의 비율을 0, 0.1, 0.2의 비율로 용액을 각각 제작하였다. 이 용액을 이용하여 Pt 위에 spin coating방법을 이용하여 1000 rpm 10초, 6000 rpm 30초의 조건으로 AZTO (Al-ZnO-Tin-Oxide) 박막을 증착한 뒤, solvent 및 불순물 제거를 위하여 $250^{\circ}C$의 온도로 30분 동안 열처리를 진행하였다. 이후 Electron beam evaporator를 이용하여 top electrode인 Ti를 100 nm 증착하였다. 제작된 메모리의 전기적 특성은 HP 4156B semiconductor parameter analyzer를 이용하여 측정하였다. 측정 결과, AZTO (0:1:1, 0.1:1:1, 0.2:1:1)를 이용하여 제작한 ReRAM에서 RS특성을 얻었으며 104 s이상의 신뢰성 있는 data retention특성을 확인하였다. 그리고 Al의 비율이 증가할수록 on/off ratio가 증가하고 endurance 특성이 향상되는 것을 확인하였다. 결론적으로 Al을 doping함으로써 ZTO film의 메모리 특성을 향상 시켰으며 AZTO film을 메모리와 트랜지스터의 active layer로써 활용 가능할 것으로 기대된다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.8
• /
• pp.1051-1060
• /
• 2003

The heat and mass transfer on two kinds of tube surfaces (bare stainless steel tube and Teflon coated tube) in steam-air mixture flow are experimentally studied to obtain design data for the heat exchanger of the latent heat recovery from flue gas. In the test section, 3-tubes are horizontally installed, and steam-air mixture is vertically flowed from the top to the bottom. The pitch between tubes is 67mm, the out-diameter of tube is 25.4mm, and the thickness is 1.2mm ; blockage factor (cross sectional tube area over the cross sectional area of the test section) is about 0.38. All of sensors and measurement systems (RTD, pressure sensor, flow-meter, relative humidity sensor, etc.) are calibrated with certificated standard sensors and the uncertainty for the heat transfer measurement is surveyed to have the uncertainty within 7%. As experimental results, overall heat transfer coefficient of the Teflon (FEP) coated tube is degraded about 20% compared to bare stainless tube. The degradation of overall heat transfer coefficient of Teflon coated tube comes from the additional heat transfer resistance due to Teflon coating. Its magnitude of heat transfer resistance is comparable to the in-tube heat transfer resistance. Nusselt and Sherwood numbers on Teflon (FEP) coated surface and bare stainless steel surface are discussed in detail with the contact angles of the condensate.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.11 no.2
• /
• pp.99-115
• /
• 2009

Recently, the development of design of cultural goods is focusing on excessively workmanship-oriented craft items. However, an advanced strategy that is practical and develops market-oriented goods in the world needs to be suggested from now on and the selection of goods item aimed to world market is very urgent. Therefore, the purpose of this study was to design practical and worldwide market-oriented shoes with Korean traditional image as a cultural goods. As software tools, 2D Adobe Illustrator Adobe Photoshop and 3D MAX 8.0 Photoshop CS were used to design the shoes. From 8 types of pattern design to which Koran traditional pattern was applied and 7 types of shoe design to which Korean traditional shoes were applied, 60 types of planar shoes design coating developed pattern designs were made. Furthermore, 3D design of cultural goods of shoe made possible to observe it three-dimensionally and accurately from the top, the front and the side respectively. Finally, 43 types of cultural goods of shoe to which Korean traditional shoes were applied were designed successfully according to traditional patterns and colors. The systematic database was established based on the developed pattern design of the shoes and might make the best use of the development of related design of cultural goods. Although there were partly some limitations in the aspects of design and material development of Korean traditional shoes, this study would help the economics of shoe industry in Korea producing high value-added products.

• Journal of Biosystems Engineering
• /
• v.35 no.4
• /
• pp.257-261
• /
• 2010

Surface energy is the principal factor of anti-condensation. High surface energy appears hydrophilic itself and low surface energy represents hydrophobic itself. The contact angle is widely being used for measurement of surface energy of materials, evaluation of coating performances, measurement of wettability, and so on. However, the existing contact angle measuring system is so expensive for purchasing and complicated, so it takes a lot of time and money to use. This study was conducted to develop the algorithm for evaluating hydrophilic performance through measuring the contact angle of water droplet automatically, and fabricate relatively simple measuring system using a low-cost monochrome camera and image processing. A constant amount of water was firstly allocated on a slide by a micropipette, and then the image of water droplet was captured by monochrome digital camera and sent to a computer. The image was binarized and then reduced noises by labeling. Finally, the contact angle of water droplet was computed by using three points (left, right, and top coordinates), simple linear mathematics, and trigonometric function. The experimental results demonstrated the accuracy and reproducibility of the developed system showing less deviations and deviation ratio.

• Korean Journal of Materials Research
• /
• v.21 no.4
• /
• pp.236-241
• /
• 2011

Polysilazane and silazane-based precursor films were deposited on stacked TiN/Ti/TEOS/Si-substrate by spin-coating, then annealed at $150{\sim}400^{\circ}C$, integrated further to form the top electrode and pad, and finally characterized. The precursor solutions were composed of 20% perhydro-polysilazane ($SiH_2NH$)n, and 20% hydropolymethyl silazane ($SiHCH_3NH$)n in dibutyl ether. Annealing of the precursor films led to the compositional change of the two chemicals into silicon (di)oxides, which was confirmed by Fourier transform infrared spectroscopy (FTIR) spectra. It is thought that the different results that were obtained originated from the fact that the two precursors, despite having the same synthetic route and annealing conditions, had different chemical properties. Electrical measurement indicated that under 0.6MV/cm, a larger capacitance of $2.776{\times}10^{-11}$ F and a lower leakage current of 0.4 pA were obtained from the polysilazane-based dielectric films, as compared to $9.457{\times}10^{-12}$ F and 2.4 pA from the silazane-based film, thus producing a higher dielectric constant of 5.48 compared to 3.96. FTIR indicated that these superior electrical properties are directly correlated to the amount of Si-O bonds and the improved chemical bonding structures of the spin-on dielectric films, which were derived from a precursor without C. The chemical properties of the precursor films affected both the formation and the electrical properties of the spin-on dielectric film.

• Journal of the Korean Society of Tobacco Science
• /
• v.2 no.1
• /
• pp.61-67
• /
• 1980

The greenhouse hulk curing and drying system utilizing the direct solar energy was tested to see how much fuel could be saved for curing flue-cured tobacco at the Daegu Experiment Station, Korea Tobacco Research Institute (North latitute: 35$^{\circ}$49'), in 1979. The structure consists of transparent fiberglass exterior, polyurethan boards covered with galvanized iron as the heat absorbers and insulation boards, air duct in which the air is introduced to the furnace room of bulk curing barn, and gravel heat storage system. All exterior surface of heat absorbers, air duct, and gravels were coated with black paint. The air temperature and total radiation were 20.5 to 35.5$^{\circ}C$ and 1004.2 to 1436.2 cal/$\textrm{cm}^2$ during the 3 replicated curing tests, respectively. The greenhouse bulk curing and drying system was able to cut fuel consumption by 25 percent compared with the conventional bulk curing barn. The maximum temperatures for the top absorber and the inlet air of the system were 89$^{\circ}C$ and 64$^{\circ}C$, respectively, and the average temperature of inlet air was higher than that of conventional one by 18$^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.3
• /
• pp.229-236
• /
• 1998

Ferroelectric $Sr_xBi_yTa_2O_{9+\alpha}$/(0.7$\leqSr\leq1.0,\; 2.0\leqBi\leq2.6)$ solutions were prepared by MOD (Metalorganic Deposition) process. These solutions were made into thin films with thickness ranging from 1500~2000${\AA}$ by spin coating. The phase transformation of the SBT thin films by variation of annealing temperature and annealing time were observed using high temperature XRD and SEM. The crystallization and grain growth of SBT thin film were accomplished at $800^{\circ}C$ for 30 minutes after deposition of Pt top electrode by sputtering to prevent electrical breakdown. Ferroelectric properties of the SBT thin films were measured in the range of $\pm$3V\; and\; \pm5V$. The specimen with composition ratio of Sr/Bi/Ta (0.8/2.4/2.0) has the excellent ferroelectric properties ; $2P_r = 10.5,\; 13.2\muC/cm^2 \;at\; \pm3V\; and\; \pm5V$ respectively. Observing the post annealed Pt/SBT/Pt interface by SEM, it was found that Pt electrode sputtered on to the SBT thin film penetrated into the hollow on the SBT thin film, thus decreasing the effective insulation thickness. The effective insulation thickness recovered by post annealing, and this was confirmed by leakage current density measurement.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.17 no.3
• /
• pp.254-260
• /
• 2007

Trichloroethylene(TCE) is widely used as a degreasing solvent in workplaces. TCE is primarily toxic to the nervous system, however, systemic disorder like Stevens-Johnson syndrome has been recently reported in small-scale factories, where the government has had limited information of chemical use. A survey was performed to investigate the actual condition of using TCE and to provide practical information to occupational health service agencies and professionals. This survey was carried out on 103 factories out of 430 factories which were conducted periodic work environment measurement for TCE. Degreasing was the most popular reason for using TCE in Korea, which reached to 94%. TCE was also used as a solvent for rubber in the coating or molding process, and adhesives in the bonding process. Metal fabrication was the most common as 23%, followed by assembling automobile parts (17%), and machinery (12%). Workers exposed to TCE during full-shift were 52% while 48% were exposed during short period of the shift or intermittently. Manual or semi-automatic work occupied 87% while automatic work was just 13%. Though automatic work by a closed system was generally lower exposed to TCE, compared to manual work, it can cause a high exposure when the maintenance system is improper. Semi-automatic work especially like open-top degreasing process can cause a high exposure when local exhaust system with condensing and refrigerating coils in the degreaser does not work well. In conclusion, the survey showed nationwide status of TCE exposure in various aspects. It can be used to monitor workplaces and workers exposed to TCE to prevent occupational diseases.

• Journal of Sensor Science and Technology
• /
• v.9 no.1
• /
• pp.9-14
• /
• 2000

Dielectric characteristics of P(VDF/TrFE) film manufactured using spin coating technique have been investigated. To improve the crystallinity and quality of film, the film was three step annealed. Simple etching process and conditions for P(VDF/TrFE) film were established using top electrode as a mask. Poling is performed by several steps. $1.87\;{\mu}m$ thick P(VDF/TrFE) films were obtained with conditions such that the solution of 10 wt% concentration was spun at 3000rpm for 30 seconds. Before poling, dielectric constant and dielectric loss of P(VDF/TrFE) film were 13.5 and 0.042, respectively. After poling, dielectric constant and dielectric loss of P(VDF/TrFE) film were 11.5 and 0.037, respectively.