• 대한기계학회논문집B
• /
• 제25권11호
• /
• pp.1616-1623
• /
• 2001

A basic experimental study has been carried out to find out the design parameters of fuel 2-staging atomizers in order to reduce nitrogen oxides(NOx) rate emitted from the steam boilers used the liquid fuel. The heavy fuel oil(B-Coil) and fuel 2-staging Y-jet twin-fluid atomizers were adopted in this study. The results of this paper were obtained from the real as well as the model scale atomizers. In the case of model atomizers test, NOx reduction rate was strongly dependent on the staged fuel rate, but it was weakly dependent on the injection hole arrangement and air swirl conditions. The real scale atomizers was designed and manufactured on the base of these test results, and those was mounted and operated in the real boiler generates 185 ton steam per an hour. The reduction rate of the model and real plant was reached 10∼30% of base NOx by atomizers. but dust was sharply increased in the low O$_2$combustion region of the real plant.

• 한국주조공학회지
• /
• 제31권1호
• /
• pp.11-17
• /
• 2011

The effect of CaO addition to AM60B Mg alloy on tensile properties has been investigated, with focus on strength and ductility at room and elevated temperatures. The 0.25-0.65wt% CaO added AM60B Eco-Mg diecastings were prepared by high pressure die casting using Buhler 1,450-ton cold chamber machine without $SF_6$ and $SO_2$ gases. The microstructures and tensile properties of each alloy were tested. The results show that the grains of AM60B are refined and the mechanical properties increase with CaO addition at room temperature. The improvement of strength and ductility is prominent at 0.45-0.55wt% CaO addition. Also, improved mechanical properties are maintained at elevated temperature of $150^{\circ}C$. CaO addition results in $Al_2Ca$ phase formation mostly on the grain boundaries. This phase leads to the refinement of grain structures and improvement of ductility as well as strength. The suppression of ${\beta}-Mg_{17}Al_{12}$ phase as well as the decrease of fracture surface porosity and other casting defects caused by melt cleanliness also contribute to the enhancement of mechanical properties of AM60B Eco-Mg at room and elevated temperature.

• 한국육종학회지
• /
• 제43권3호
• /
• pp.184-189
• /
• 2011

신품종 '영한'은 병해 및 도복, 한해 등 재해에 강해 수량이 많고 품질이 우수한 청보리 품종을 육성하기 위하여 1997년에 조숙, 내도복, 내병, 다수성 계통인 'YB3433-3B-5'와 조사료 품질이 좋고 수량이 많은 'YB3135-3B-2-3' 사이의 $F_1$에 'YB3135-3B-2-3'를 여교잡하고 계통육종법에 의하여 제반특성이 우수한 'SB971305-B-B-B-B-4-4' 계통을 선발, 생산력검정시험과 지역적응시험을 거쳐 2008년에 육성되었다. 1. '영한'은 직립 초형으로 파성은 IV이고, 잎은 녹색이면서 넓으며, 줄기 굵기는 중간 정도이고, 까락은 조망으로 길며, 종실은 황색이다. 2. '영한'의 초장은 98 cm로 큰 편이었고, $m^2$당분얼수는 639개로 표준품종인 '영양'보다 38개 많은 다얼성이었으며, 적응지역에서 평균 출수기는 '영양'의 4월 26일보다 평균 1일 빨랐다. 3. '영한'은 '영양'에 비해 도복, 한해에 강하였으며, 호위축병은 익산(III형)에서 중도저항성, 나주(I형), 밀양과 진주(IV형)에서는 저항성을 보였다. 4. '영한'의 건물수량은 적응지역에서 12 ton/ha로 '영양'에 비해 3% 증수하였고, TDN 수량이 8.1 ton/ha으로 6% 증수하였다. 5. 조사료 품질은 조단백질 함량 8.5%, 소화율 52.3%, 젖산 함량 0.98 g/100g으로 '영양'보다 높았으며, ADF 27.2%, TDN 67.4%로 대등하였으며, 사일리지 등급은 II 등급으로 양호하였다.

• Environmental Engineering Research
• /
• 제25권1호
• /
• pp.96-103
• /
• 2020

The aim of this study is to investigate the effect of five different combinations including: sand 70%, bentonite 30% (S₇₀B₃₀)- sand 80%, bentonite 20% (S₈₀B₂₀)- sand 80%, organophilic 20% (S₈₀M₂₀)- sand 60%, bentonite 20%, organophilic 20% (S₆₀B₃₀M₂₀) and sand 75% - bentonite 15% - organophilic 10% (S₇₅B₁₅M₁₀) on landfill linear structure in order to decrease phenol leaching. Hydraulic conductivity and adsorption behavior of the samples were investigated. The results demonstrated that the lowest hydraulic conductivity coefficient ($1.16{\times}10^{-11}{\frac{m}{s}}$) was obtained for S₇₀B₃₀. Furthermore, adding more than 20% of bentonite had no significant effect on reducing permeability. Moreover, Freundlich isotherm was introduced as the best model explaining adsorption behaviour due to its highest determination coefficient (0.945). The best samples for adsorption capacity of phenol and for both permeability and adsorption are S₈₀M₂₀ and S₆₀B₃₀M₂₀, respectively. Although the presence of bentonite was effective in reducing hydraulic conductivity, organic clay had no considerable impact on reducing permeability. Though, it's an exceptional role in adsorbing organic contaminants including phenol cannot be ignored. To meet all regulatory constraints, the optimal compound is made up of 10.2% of bentonite and 2.8% of organophilic clays with a minimized cost of 13.64 ($/ton).

• Journal of Preventive Medicine and Public Health
• /
• 제6권1호
• /
• pp.27-41
• /
• 1973

In order to provide some basic data for the control of air and water pollution in Korea, the authors have estimated the amount of air and water pollutants emitted from industries which are employed over 20 employees. This study have done from July 1, 1972 to the end of March 1973. The results are as followings; 1. Total number of establishments with over 20 employees is 5,197 in Korea and the largest group establishments was the manufacturing of textiles with 1,363 establishments (26.2%). 2. By order of number of employees it was observed that there 2,800 industries with 20-59(53.9%) employees, 1,101 with 50-99 (21.2%), 571 with 100-199 (11.0%), 501 with 200-499 (9.6%) and 225 with over 500 (4.3%) respectively. 3. By order of regional distribution, it was observed that there were 2,257 industries in Seoul (43.2%) and 736 industries in Pusan(14.2%). 4. Industrial coal consumption was 596,154 M/T in 1972, but it' 11 be 315,000 M/T in 1980. Fuel consumption was 4,972,000 K1 in 1972, and estimated volume will be 19,370,000 K1 in 1980. 5. Total amounts of air polutants entitled from industries by fuel combustion were sulfur oxides 79,459 tons, carbon monoxide 33,908 tons, particulate 31,304 tons and hydrocarbon 30,280 tons in 1972 but in 1990 there will be sulfur oxides 1,010,474 tons, nitrogen oxides 204,575 tons, carbon monoxide 68,014 tons, particulate 64,820 tons and hydrocarbon 67,622 tons, respectively. 6. Annual emitted air pollutants through the working processes were sulfur oxides 91,250 tons and nitrogen oxides 32,485 tons in 1972, but sulfur oxides 118,625 tons and nitrogen oxides 42,555 tons will be present in 1980, respectively. 7. Annual emitted air pollutants by national unit area amounted to $0.77ton/km^2/year$ in 1965 and $14.7ton/km^2/year$ in 1980. 8. Total industrial wastes from all industries in Korea were estimated at 810,360 tons/day in 1972; manufacturing of chemicals and plastic products showed the highest amount of wastes at 470,000 tons/day. 9. The amounts of water pollutants due to industrial wastes were the B.O.D., 471.5 tons/day, suspended solid 331.5 tons/day, CN, 2.3 tons/day, and Cr. 3.4 tons/day in 1972, but it might be evident of a B.O.D. of 3,388 tons/day, suspended solid 2,544 tons/day, CN 20.1 tons/day, and 26.5 tone/day in 1990. 10. Total population equivalent of B.O.D. was 943,000 in 1972, and the estimated value in 1950 will be 6,780,000.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.197-198
• /
• 2008

The forging process produces complicated and designed components in a die at high productivity for mass production and minimizes the machining amount for favorable material utilization; the forging products used at highly stressed sections are well accepted at a wide range of industry such as automobile, aerospace, electric appliance and et cetera. Accordingly, recent R&D activities have been emphasized on improvement of forging die-life and near net shaping technology for cost effectiveness and better performance. Usually closing and consolidation of internal void defects in a ingot is a vital matter when utilized as large forged products. It is important to develop cogging process for improvement of internal soundness without a void defect and cost reduction by solid forging alone with limited press capacity. For experiments of cogging process, hydraulic press with a capacity of 800 ton was used together with a small manipulator which was made for rotation and overlapping of a billet. Size of a void was categorized into two types; ${\phi}$ 6.0 mm and ${\phi}$ 9.0 mm to investigate the change of closing and consolidation of void defects existed in the large ingot during the cogging process. In addition for forming experiment of piston grown air drop hammer with a capacity of 16 ton was used. The experiment with piston crown was carried out to show the formability and void closing status. In this paper systematic configuration for closing process of void defects were expressed based on this experiment results in the cogging process. Also forging defects through forming process for piston crown was improved using the experiment results and FE analysis. Consequently this paper deals with the effect of radial parameters in cogging process on a void closure far large forged products and formability of piston crown.

• Rapid Communication in Photoscience
• /
• 제3권4호
• /
• pp.70-72
• /
• 2014

Visible-light irradiation of MeCN solution containing di(hydroxo)metallo(tetraphenyl)porphyrin complex $(tppM(OH)_2$: 1a; $M=Sb(V)^+Br^-$, 1b; $M=P(V)^+Cl^-$, 1c; M=Ge(IV)) and 2-mercaptoethanol (2-ME) as a substrate under aerated condition gave bis(2-hydroxyethyl)disulfide (2-HEDS) as an oxidative product of 2-ME. It is indicated that the oxidation of 2-ME should proceed with a photocatalytic process by 1, because the turn over number (TON) for the formation of 2-HEDS was over unit. The TON was determined to be 642 as a maximum value when 1a was used as a sensitizer. The formation of 2-HDES was extremely slow under argon atmosphere. The fluorescence of 1 was not quenched by 2-ME at all, and the free energy change (${\Delta}G$) with electron transfer (ET) from 2-ME to excited triplet state of $1(^31^*)$ was estimated as a negative value. The quenching rate constant ($k_r$) of $^31^*$ by 2-ME, obtained by the kinetics for the formation of 2-HEDS, strongly depends on ${\Delta}G$. These findings indicate that 1-sensitized oxidation was initiated by photoinduced ET from 2-ME to $^31^*$ to generate both radical cation of 2-ME ($2-ME^{+\bulle}$) and porphyrin radical anion ($1^{-\bulle}$), resulting that the formation of 2-HEDS can be proceeded by the dimerization of $2-ME^{+\bulle}$, and through a catalytic cycle due to returning to 1 by the ET from $1^{-\bulle}$ to molecular oxygen.

• 마이크로전자및패키징학회지
• /
• 제8권1호
• /
• pp.53-59
• /
• 2001

Surfaces of PTFE and PVDF were modified by ion-assisted reaction (IAR) in which 1 keV $Ar^{+}$ ions were irradiated on the surface of the polymer with varying ion dose in an oxygen gas environment, and Cu, Pt, Al and Ag thin films were deposited on the modified polymers. Wettability of the modified polymers was largely improved by the formation of hydrophilic groups due to chemical reaction between polymer surface and the oxygen gas during IAR. The change in wettability in the modified polymers was also related to the change in surface morphology and roughness. Adhesion between metal films and polymers modified by IAR was significantly improved, so that no detachment was possible in the $Scotch^{TM}$ tape test. The increase of adhesion strength between the metal film and the modified PVDF was mainly attributed to the formation of hydrophilic groups, which interacted with the metal film. In the case of the modified PTFE, the enhanced adhesion to metal film could be explained by the change in surface morphology together with the formation of hydrophilic groups. The electrical properties of the metal films on the modified polymers were also investigated.

• 한국해양환경ㆍ에너지학회지
• /
• 제14권2호
• /
• pp.73-80
• /
• 2011

어선용 고효율 표준 프로펠러 개발에 대해 고찰해 보았다. 어선용 프로펠러의 경우 모형시험이나 이론해석을 통한 정도 높은 설계가 이루어지지 않고 시리즈 데이터(주로 MAU 시리즈)에 의존하여 초기설계 수준에 머무르고 있는 실정이다. 본 연구에서는 52톤 어선을 기준으로 개발되었으며 기존 MAU 형 프로펠러보다 성능이 우수한 프로펠러를 손쉽게 설계, 적용할 수 있는 NACA형 단면을 사용한 시리즈 프로펠러 자료를 제공하기위한 연구를 수행하였다. 또 한 기존의 복잡한 설계 방식 대신에, NACA형 프로펠러를 표준화하여 보다 편리하게 사용할 수 있도록 하였다. 향후 모형 시험을 통한 추진 성능 및 캐비테이션 성능 검증을 수행할 계획이다.

• 한국주조공학회지
• /
• 제22권3호
• /
• pp.121-129
• /
• 2002

According to the investigation of waste $CO_2$ molding sand in the 15 steel foundries in Busan and Gyeong area, about 1 ton of waste $CO_2$ molding sand per ton of steel castings production was produced In order to reduce amount of $Na_2O$, Loss of Boiling (L.O.B), Loss of Ignition (L.O.I), Conductivity and PH which are present in the waste $CO_2$ molding sand below the reclamation effect, more than 50% of elimination for reclamation was required. It was found that the waste $CO_2$ molding sand does not contain a harmful component designated by industrial waste materials. Reclamation of the waste $CO_2$ molding sand was practically achieved by an abrasive-dry reclamation process. According to bench time of the sodium silicate-bonded $CO_2$ molding sand, reduction of compressive strength and surface stability index(S.S.I) become slowdown. Therefore, the reclaimed sand could be allowed the reuse of molding sand in $CO_2$ molding process including core sand.