• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.541-548
• /
• 2014

This study was performed to obtain high conversion efficiency of $C_7H_8$ using non-thermal plasma and metal-supported catalyst. Adsorption-desorption characteristics of toluene was performed using 4A type (Zeolite) filled in a concentration reactor. Through this test, it was found that the concentration reactor has 0.020 g/g of adsorption capacity (at ambient temperature and pressure) and 3,600 ppm of desorption property at $150^{\circ}C$ (with in 20 min). In case of developed catalyst, toluene decomposition rate of Pd-AO (Pd coated catalyst) was better than Pd/Cu-AO and Pd/Ag-AO (Pd/Ag composite metal catalyst). Developed non-thermal plasma system was obtained flame amplification effect using injection process of desorbed tolune, and 98% of removal efficiency.

• Korean Chemical Engineering Research
• /
• v.57 no.3
• /
• pp.358-367
• /
• 2019

Adsorption equilibrium and intraparticle diffusion characteristics of benzene, toluene, and xylene vapors on activated carbon and zeolite 13X were investigated. Static adsorption experiments were carried out under the pressure range of 0.01~0.07 bar while changing the adsorption temperature to 293.15 K, 303.15 K, and 313.15 K, respectively. Adsorption equilibrium was analyzed by Langmuir, Freundlich and Toth models. The adsorption energy was 5.26~31.0 kJ/mol representing physical adsorption characteristics. The maximum adsorption capacity on activated carbon was the largest for benzene, and the smallest for xylene. Toluene was in between. In the case of zeolite 13X, the maximum adsorption capacity was the largest for xylene, and the smallest for benzene as opposed to activated carbon. The effective diffusion coefficients of gas adsorbate were measured to be about $10^{-5}{\sim}10^{-4}cm^2/s$, and increased with temperature. As the pressure increased, the effective diffusion coefficients were decreased. The dependence of effective diffusion coefficients on temperature and pressure was greater in zeolite 13X particles than in activated carbon. Therefore, it is necessary to express the diffusion coefficients as a function of pressure in order to predict the precise dynamic behavior of the adsorption process using zeolite 13X where the pressure fluctuation occurs abruptly.

• Journal of Environmental Science International
• /
• v.20 no.6
• /
• pp.729-736
• /
• 2011

This work is to compare the experiment results by a continuous fixed-bed adsorption of water vapor, acetone vapor, and toluene vapor on zeolite 13X (SAU) and silica-alumina (SAK). SAU and SAK have very different pore structure but similar composition as inorganic adsorbent. The relationship between the equilibrium adsorption capacity and specific pore size range were studied. Adsorption of water vapor was more suitable on SAU than SAK because SAU has relatively more developed pores around $5\;\AA$ than SAK in the pore range of $10\sim100\;\AA$. Adsorption of acetone vapor was more suitable on SAK than SAU because SAK has relatively more developed pores around $5\sim10\;\AA$ than SAK in the pore range of less than $10\;\AA$. Adsorption of toluene vapor was more suitable on SAK than SAU because SAK has relatively more developed pores in the pore range of $10\sim100\;\AA$ than SAK. Adsorption capacity of the adsorbent was closely related to the surface area generated in the specific pore size region. But it was difficult to distinguish the relationships between adsorption capacity and micro area, and the external surface area of adsorbent.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.219.2-219
• /
• 2003

• Journal of Environmental Science International
• /
• v.18 no.5
• /
• pp.501-508
• /
• 2009

In this study, the characteristics of granular activated carbon (GAC) supported metal was investigated in an area influenced by flame discharge and temperature variation during irradiating microwave. The modified GAC was formulated by impregnating metal hydroxides of nickel (Ni/GAC), barium (Ba/GAC), copper (Cu/GAC), zinc (Zn/GAC), cobalt (Co/GAC) and lanthanum (La/GAC). Ba/GAC was selected as it showed lack of spark discharge and temperature increasing aspects. Comparison of adsorption and desorption amount of GAC and Ba/GAC showed that adsorption and desorption rate of the GAC were higher than those of Ba/GAC. The results show that the presence of barium can decrease adsorption/desorption rate because of plugging pore of GAC. Toluene regeneration rate of Ba/GAC was better than that of GAC due to barium loading. Finally, GAC with barium can be controled a rapid increasing temperature and spark discharge, increased the regeneration rate of toluene during desorption by irradiating microwave.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.3 s.131
• /
• pp.45-52
• /
• 2005

This research was performed to evaluate adsorption behavior of woody charcoals obtained from wood powder, fiber and bark of spruce (Abies sibirica Ledeb). The wood materials were carbonized at various temperatures for 1 hour using experimental rotary kiln without any inert gas. The adsorption capacity of iodine and toluene, specific surface area and removal efficiency of acetic acid and ammonia gas of those charcoals were measured. The higher was the temperature for carbonization, the lower yields of charcoals were. Ash content of bark charcoal was higher than that of wood powder charcoal or fiber charcoal. Elemental analysis of woody charcoal revealed that the content of carbon was gradually lincreased as carbonization temperature was higher. When carbonization temperature was higher, adsorption capacity of woody charcoals for iodine was much improved. Wood powder charcoal and fiber charcoal were more effective for iodine adsorption rather than bark charcoal. Capacity of toluene adsorption was the highest in the charcoal of $600^{\circ}C$. Charcoals produced at high temperature efficiently removed acetic acid gas, while charcoals carbonized at low temperature such as $400^{\circ}C$ were proper to remove ammonia gas. This difference may be explained that the acidity of charcoals depends on the carbonization temperature: charcoals of low temperature indicate acidic property, while those of high temperature turned to alkaline.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.5 no.2
• /
• pp.119-127
• /
• 1995

The purpose of this study was to determine the effects of surface-treatment by zinc salts on break-through and adsorption capacity of toluene. Firstly, the coconut activated carbon treated the surface with zinc salts, were exposed by the spike sample(toluene, 69.02ppm, $260.1mg/m^3$), and then the effects of zinc salts were examined by using the gas adsorption kinetics. The results obtained were as follows : 1) BET(Brumaure Emmett Teller) surface area were $954.4m^3/g$ in coconut activated carbon treated with 0.0001 N $Zn(NO_3)_3$ $6H_2O$, and $830.3m^2/g$ in coconut activated carbon treated with 0.0001 N $ZnCl_2$. 2) Migration was decreased in coconut activated carbon treated with the thin level of zinc salts. 3) Breakthrough volume were 73.07 L in coconut activated carbon treated with 0.0001 N $Zn(NO_3)_3$ $6H_2O$, and 72.76 L in charcoal treated with 0.0001 N $ZnCl_2$. 4) ${\tau}$ values(the time required for 50% breakthrough) were 1046.1 min in coconut activated carbon treated with 0.0001 N $ZnCl_2$ and 921.2 min in coconut activated carbon treated with 0.0001 N $Zn(NO_3)_3$ $6H_2O$. 5) Maximum adsorption capacity was 53.9 mg/tube in coconut activated carbon treated with 0.0001 N $ZnCl_2$ and 47.4 mg/tube in coconut activated carbon treated with 0.0001 N $Zn(NO_3)_3$ $6H_2O$. In conclusion, the coconut activated carbon treated the surface with the thin concentration of zinc salts, decreased the breakthrough and increased the BET surface area and the adsorption capacity in case of sampling airborne toluene.

• Journal of the Korean Applied Science and Technology
• /
• v.34 no.4
• /
• pp.799-806
• /
• 2017

The potential use of modified clays in the adsorption of vapor phase benzene and toluene was investigated. The modified clays OC-CPC, IOC, and Al-PILC were prepared for comparative purposes and were characterized using infrared spectroscopy, thermogravimetric analysis, and X-ray diffraction. It was confirmed the intercalation of the aluminium pillar in IOC and Al-PILC, as well as the introduction of cetylpyridinium. The adsorption studies showed a great affinity of benzene and toluene for OC-CPC due to the hydrophobic character that resulted and also to the increase in the interlaminar distance. IOC showed a lower affinity for the benzene and toluene, followed by Al-PILC. Natual clay had no affinity for benzene and toluene due to its hydrophilic nature. Clay materials having a laminar structure can be chemically modified, changing their physiochemical characteristics, such as interlaminar distance, surface area, pore size, and chemical affinity. In this study, it was focused on obtaining modified clays to be used for the adsorption of volatile organic chemicals.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.6
• /
• pp.805-812
• /
• 1999

Adsorption characteristics of volatile organic compounds(VOCs) by activated carbon fiber(ACF) were investigated using a continuous system for benzene, toluene, xylene(BTX) generation. Studied characteristics for adsorption were equilibrium capacity, accumulative adsorption, and breakthrough curve. Operating variables were adsorption temperature(25~45$^{\circ}C$) and partial pressure(1.2~12 mmHg) of BTX. The experimental results show that the adsorption equilibrium capacity increases with increasing partial pressure of BTX and decreases with increasing temperature. It was also found that the break point was decreased with increasing partial pressure, temperature and gas flow rate due to an effect of mass transfer of adsorbate.

• Environmental Engineering Research
• /
• v.22 no.2
• /
• pp.169-174
• /
• 2017

Vacuum swing adsorption (VSA) is a promising treatment method for volatile organic compounds (VOCs). This study focuses on a VSA process for regenerating activated carbon spent with VOCs, and then investigates its adsorption capacities. Toluene was selected as the test VOC molecule, and the VSA regeneration experiments results were compared to the thermal swing adsorption process. Cyclic adsorption-desorption experiments were performed using a lab-scale apparatus with commercial activated carbon (Samchully Co.). The VSA regeneration was performed in air (0.5 L/min) at 363.15 K and 13,332 Pa. The comparative results depicted that in terms of VSA regeneration, it was found that after the fifth regeneration, about a 90% regeneration ratio was maintained. These experiments thus confirm that the VSA regeneration process has good recovery while operating at low temperatures (363.15 K) and 13,332 Pa.