• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.887-887
• /
• 2004

The areal density of the hard disk drive(HDD) has been increased due to technological advances recently. To achieve the high areal density magnetic recording requires an extremely small gap between the air-bearing surface (ABS) and disk. At the same time, the slider mass and size should be reduced to minimize the physical contact under the operational and environmental conditions. Almost all of 2.5＂HDD companies will get ready for adoption of FEMTO slider and already utilized the small slider. FEMTO and small size slider will be mainstream in the 2.5" and other small form factor HDD in the near future. In this study, the flying characteristic of FEMTO slider was examined. Based on the simulation, FEMTO slider is very stable in flying dynamic under the disk modulation, however the flying height sensitivity of the manufacturing tolerances is much bigger than PICO slider. And the other characteristics like impulse response and load/unload dynamic were also examined in this study.tudy.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.753-758
• /
• 2004

This study is to suggest a probabilistic design determining configurations of slider air bearings with the dimensional manufacturing tolerances of the ABS. The probabilistic design problem is formulated to minimize the variation in flying height from a target value while satisfying the desired probabilities keeping the pitch and roll angles within suitable range. The proposed approach first solves the deterministic optimization problem. Then, beginning with this solution, the RBDO is continued with the probabilistic constraints affected by the random variables with a fixed standard deviation in normal distribution. The RBDO results are directly compared with the values of the initial design and the results of the deterministic optimization, respectively. The reliability analyses are performed by the descriptive sampling (DS) to show the effectiveness and accuracy of the proposed approach. It is demonstrated that the proposed RBDO approach can efficiently obtain an optimum solution satisfying all the desired probabilistic constraints.

• Proceedings of the Korean Society of Plant Biotechnology Conference
• /
• 2005.11a
• /
• pp.84-87
• /
• 2005

The citrus industry represents a major sector of agribusiness in Jeju successfully nurtured by the local governmental farm bureaus for the past three decades. However, in the face of increasing imports effected under the international free trade agreement, the continuous economic viability of the island’s citrus industry is no longer assured. Thus, it entails exploration and development of new agribusiness potentials that are supplemental and/or alternative to the citrus industry. In this presentation, I will discuss two projects of such potentials. (i) Under the tripartite collaboration among Kumho Life and Environmental Science Laboratory, Cheju National University and South Jeju County, genetically engineered turfgrass cultivars possessing both herbicide- and shade-tolerances (gene pyramiding) are currently at final phase of phenotype evaluations and environmental safety assessments. (ii) Fig fruits with longer shelf-life are being developed with support from Jeju HiTech Industrial Development Institute (HiDI) and at its initial phase of development.

• Transactions of Materials Processing
• /
• v.23 no.4
• /
• pp.206-210
• /
• 2014

The metal lead frame, a semiconductor component, has product tolerances in micro units as compared to products made with a larger size mold. Therefore, small deflections of the mold and of the press as well as the press molding process itself have a strong influence on accuracy of the product. Hence, it is necessary for the process design to consider the structural response of the mold and the press during deformation. In the current study, the mold deflection and pressure on the punch is examined using the finite element modeling (FEM) program ABAQUS. The results from the simulation were verified with the dynamic deformation measurement equipment using digital image correlation (DIC).

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.4
• /
• pp.420-426
• /
• 1998

It is the purpose of this paper to make a preliminary study on the use of repetitive control to improve velocity accuracy by eliminating repetitive disturbances caused by machining inaccuracies of the axis of rotation location. If the control system can be intelligent enough to compensate for such machining errors, then one may be able to improve the accuracy of the velocity control, or alternatively, one may maintain the same accuracy and relax the machining tolerances required. This could decrease cost significantly. Experiments are performed testing repetitive control methods on a constant speed rolling operation testbed. The experimental results show very substantial decreases in the tracking error of the system. Spectral data of the output motion are given to demonstrate the attenuation of the disturbance frequencies and harmonics, related to the bandwidth being used. It is seen that the simplest form of repetitive control which is very easily implemented, can produce striking improvement in control system performance in such belt drive rolling operations, and the learning can be accomplished in a short time.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.366-370
• /
• 2003

This paper introduces a new design and fabrication technology of 28 GHz low-cost up and down converter modules for digital microwave radios, The design of the converter module is based on unit circuit blocks, which are to be characterized using a special test fixture. Based on the cascade analysis of the module the 28 GHz up and down converter modules have been designed and implemented. The measured module performance agrees with the cascade analysis. New components such as a tapped edge-coupled filter and a new Ka-band waveguide-to-microstrip transition, which are less sensitive to fabrication tolerances, have been used in the module implementation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.236-241
• /
• 2008

The effect of organic solvent mixture ratio on the rheology property of slurry and thickness control of ceramic green sheet was investigated. For selecting a suitable dispersant multiple light scattering method was used to evaluate the particle migration velocity and variation of clarification layer thickness. Using the selected dispersant the dispersion property of solution according to solvent mixture ratio was investigated. Binder and plasticizers were added to formulate slurries and their viscosity was evaluated according to solvent mixture ratio. Ceramic green sheets with average thickness of 30, 50 urn were fabricated via tape casting and their thickness tolerances measured. As a result according to solvent mixture ratio the solution and slurry properties varied and for the mixture ratio of ethanol/toluene of 80/20 the ceramic green sheet with the lowest thickness tolerance was obtained.

• Journal of Mechanical Science and Technology
• /
• v.19 no.spc1
• /
• pp.350-356
• /
• 2005

A method of dynamic analysis of mechanical systems considering probabilistic properties is proposed in this paper. Probabilistic properties that result from manufacturing tolerances can be represented by means and standard deviations (or variances). The probabilistic characteristics of dynamic responses of constrained multi-body systems are obtained by two ways : the proposed analytical approach and the Monte Carlo simulation. The formerpaper, necessitates sensitivity information to calculate the standard deviations. In this a direct differentiation method is employed to find the sensitivities of constrained multi-body systems. To verify the accuracy of the proposed method, numerical examples are solved and the results obtained by using the proposed method are compared to those obtained by Monte Carlo simulation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.2
• /
• pp.327-336
• /
• 1997

This paper addresses an analytical approach to the mechanical error analysis and tolerance design of a four-bar path generator with lubricated joints. The mobility method is applied to consider lubrication effects and the four-bar path generator is stochastically modeled by using the clearance vector model for methanical error analysis. To show the validity of the proposed method, the mechanical errors obtained by applying the method to a four-bar path generator are compared with those by Monte Carlo simulation. Based on this analytical method, an optimal tolerance design problem is formulated and solved for the four-bar path generator.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.1
• /
• pp.90-96
• /
• 2013

During the cold forming, due to high working pressure acting on the die surface, failure mechanics must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. Die wear affects the tolerances of formed parts, metal flow and costs of process etc. The only way to control these failures is to develop methods which allow prediction of die wear and which are suited to be used in the design state in order to optimize the process. In this paper, the wear experiments to obtain the wear coefficients and the upsetting processes was accomplished to observe the wear phenomenon during the cold forming process. The analysis of upsetting processes was accomplished by the rigid-plastic finite element method. The result from the deformation analysis was used to analyse the die wear during the processes and the predicted die wear profiles were compared with the measured die wear profiles.