• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2007년도 The 1st International Symposium on Advanced Magnetic Materials
• /
• pp.22.2-22.2
• /
• 2007

• 한국세라믹학회지
• /
• 제24권4호
• /
• pp.392-396
• /
• 1987

Pure barium titanate was sintered at $1340^{\circ}C$ for 2, 4, 8, 16 hr to control their grain size. The measurements of breakdown strength and partial discharge characteristics were performed under rising AC voltage(60Hz). With increase of sintering time, the average grain size was increased and breakdown strength was slightly decreased. Partial discharge in pores was observed under high voltage, and a model of dielectric break down in barium titanate ceramics is proposed.

• 한국세라믹학회지
• /
• 제22권4호
• /
• pp.15-20
• /
• 1985

$(Ba_{0.5} Pb_{0.5})_{1-x} Nd_x TiO_3$ 중의 $_x(Nd$의 양)를 변화시키면서 격자상수와 전기전도도를 측정하였다 c축과 a축의 비(c/a) 의 극대값은 실온에 있어서 전기전도도의 극대값과 일치하였다. 이것은 Nd원자의 치환위치와 강유 전성의 변화에 의한 것으로 고찰되었다 Curie 온도이하에서는 Nd 첨가량의 증가에 따라 전기전도도의 활성화에너지가 증가하는 경향을 나타내었다 이것은 입경의 감소에 따른 Spontaneous polarization의 저하가 원인으로 고찰되었다 첨가량의 역학을 입계의 potential barrier의 높이와 관련지어 논하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.80.1-80.1
• /
• 2010

A strontium titanate ($SrTiO_3$)-based material with a perovskite structure is considered to be one of the promising alternatives to $LaCrO_3$-based materials since $SrTiO_3$ perovskite shows a high chemical stability under both oxidizing and reducing atmospheres at high temperatures. $SrTiO_3$ materials exhibit an n-type semiconducting behavior when it is donor-doped and/or exposed to a reducing atmosphere. In this work, $Sr_{1-x}La_xTi_{1-y}M_yO_3$ materials doped with $La^{3+}$ in A-sites and aliovalent transition metal ions ($M^{n+}$) in B-sites were synthesized by the modified Pechini method. The X-ray diffraction analysis indicated that the materials synthesized by the Pechini process exhibited a single curbic perovskite-type structure without any impurity phases, and are tolerant, to some extent, to cation doping. The sintering behaviors of $Sr_{1-x}La_xTi_{1-y}M_yO_3$ in $H_2/N_2$ and air were characterized by dilatometry and microstructural observations. The electrical conduction mechanism and the dopant effect are discussed based on the defect structures and the electrical conductivities measured at various oxygen partial pressures and temperatures.

• 한국결정학회:학술대회논문집
• /
• 한국결정학회 2002년도 정기총회 및 추계학술연구발표회
• /
• pp.19-19
• /
• 2002

Perovskite-type titanate dielectrics have attracted much attention in memory devices such as DRAMs or FeRAMs due to their high dielectric constants. However, low volatility of the Ba, Sr, Pb or Zr precursors with only thd ligands has limitations in obtaining high quality thin films by liquid source metal organic chemical vapor deposition (LS-MOCVD) processes. To improve the volatility of these precursors, many attempts have been made such as adding polyether ligands to satisfy the coordinative saturation. We report the synthesis of new precursors Ba(thd)₂(tmeea) and Sr(thd)₂(tmeea), where tmeea = tris[2-(2-methoxyethoxy)ethyl]amino, and LS-MOCVD of barium strontium titanate (BSTO) thin films using these precursors. Due to increased basicity of amines compared with ethers, it is expected that the nitrogen-donor ligand will make a strong bond to a metal than an analogous oxygen-donor ligand, consequently improving the volatility and thermal behavior of these precursors. Thin films of BSTO were grown on Pt(111)/SiO₂/Si(100) substrates by LS-MOCVD using a cocktail source consisting of the conventional Ti precursor Ti(thd)₂(O/sup i/Pr), and these new Ba and Sr precursors. As-grown films were characterized by XPS, SEM, XRD, XRF, and C-V and I-V measurements. BSTO films grown at 420℃ were stoichiometric barium strontium titanate with very smooth surface morphology and their dielectric constants were found to be as targe as 450. Dependence of the composition, microstructure and the electrical properties of the BSTO films on the growth temperature, annealing temperature, working pressure, and the composition of the cocktail source will be discussed.

• 대한화학회지
• /
• 제33권1호
• /
• pp.65-69
• /
• 1989

방사성 바륨 또는 방사성 란탄 추적자를 함유하고 있는 Ba(NO$_3)_2$ 와 TiO(NO$-3)_2$의 무기혼합용액을 옥살산의 에탄올 용액으로 적정하므로써 바륨티탄닐의 옥살산 염을 합성하였고, 이를 1000$^{\circ}$C에서 하소시켜 BaTiO$_3$를 만들었다. 옥살산염의 분석결과는 BaTiO(C$_2O_4)_2{\cdot}4H_2O$이며, 무기혼합용액중 Ba/Ti의 몰비가 0.950∼1.05 범위 내에서 화학양론적 결합으로 합성됨을 방사성 바륨 추적자의 도움으로 쉽게 확인하였고, Perovskite형의 구조임을 XRD로 확인하였다. 그리고 란탄 첨가제가 침전에 화학적으로 균일하게 혼입됨은 방사성 란탄의 추적자 실험으로 발견하였다. 이와 같은 실험적 사실로부터 침전물의 구성 성분의 결합이 분자준위에서 일어나고 또 티탄산바륨이 단일상의 결정임을 설명하였다.

• 청정기술
• /
• 제28권2호
• /
• pp.147-154
• /
• 2022

Titanate nanotubes (TNTs) were synthesized via alkaline hydrothermal treatment using commercial TiO₂ nanoparticles (P25). The TNTs were prepared at various TiO₂/NaOH ratios, hydrothermal temperatures, and hydrothermal times. The synthesized catalysts were characterized by X-ray diffraction, field-emission scanning electron microscopy, N₂ adsorption-desorption isotherms, field-emission transmission electron microscopy, and ultraviolet-visible spectroscopy. TNTs were generated upon a decrease in the TiO₂/NaOH ratio due to the dissolution of TiO₂ in the alkaline solution and the generation of new Ti-O-Ti bonds to form titanate nanoplates and nanotubes. The hydrothermal treatment temperature and time were important factors for promoting the nucleation and growth of TNTs. The TNT catalyst with the largest surface area (389.32 m² g^-1) was obtained with a TiO₂/NaOH ratio of 0.25, a hydrothermal treatment temperature of 130 ℃, and a hydrothermal treatment time of 36 h. Additionally, we investigated the photocatalytic activity of methyl violet 2B (MV) over the TNT catalysts under UV irradiation and found that the degradation efficiencies of the TNTs were higher than that of P25. Among the TNT catalysts, the TNT catalyst that was hydrothermally synthesized for 36 h (TNT 36 h) exhibited a 96.9% degradation efficiency and a degradation rate constant that was 4.8 times higher than P25 due to its large surface area, which allowed for more contact between the MV molecules and TNT surfaces and facilitated rapid electron transfer. Finally, these results were correlated with the specific surface area.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.173-179
• /
• 2000

The friction and wear characteristics of brake friction materials reinforced with aramid fiber, carbon fiber, glass fiber, and potassium titanate whiskers were investigated using a pad-on-disk type friction tester. In particular, the morphology of rubbing surfaces was carefully investigated to correlate the friction performance and properties of transfer films. The aramid fiber reinforced specimen showed severe oscillation of friction coefficient at low speed and low applied pressure. The carbon fiber reinforced specimen showing better friction stability exhibited uniform and stable transfer film than any other specimens. The glass fiber reinforced specimen showed unstable friction changes at high speed and high-applied pressure and the non-uniform transfer film was observed in both friction material and rotor surface. The potassium titanate whiskers reinforced specimen showed stable coherent transfer film. The wear test exhibited the potassium titanate whiskers reinforced specimen was lowest in wear amount and glass fiber reinforced specimen showed the severe wear.

• Korea-Australia Rheology Journal
• /
• 제18권2호
• /
• pp.103-107
• /
• 2006

Organic-inorganic composite of polyaniline and barium titanate (PANI-$BaTiO_3$) was synthesized via an in-situ oxidation polymerization of aniline in the presence of barium titanate ($BaTiO_3$) nanoparticles dispersed in an acidic medium. Barium titanate has large electric resistance and relatively high dielectric constant which is one of the essential properties for its electrorheological (ER) applications. The microstructure and composition of the obtained PANI/$BaTiO_3$ composite were characterized by SEM, FT-IR and XRD. In addition, we also employed a rotational rheometer to investigate the rheological performance of the ER fluids based on both pure PANI particle and PANI/$BaTiO_3$ composite. It was found that the composite materials possess much higher yield stresses than the pristine PANI due to unique dielectric properties of the inorganic $BaTiO_3$ particles. Finally, we also examined dynamic yield stress by analyzing its extrapolated yield stress data as a function of electric field strengths. Using the critical electric field strengths deduced, we further found that the universal yield stress equation collapses their data onto a single curve.

• Tribology and Lubricants
• /
• 제26권4호
• /
• pp.246-253
• /
• 2010

Friction characteristics of the brake friction materials without environmentally regulated ingredients were examined to find their role in the brake performance. Five friction materials were produced based on a nearcommercial formulation by changing the relative amount of potentially hazardous ingredients to health and environment, such as $Sb_2S_3$, potassium titanate, and brass fiber. Tribological properties of the friction materials were obtained using a scale dynamometer and Krauss type tribometer. Results showed that the excluded three ingredients played important synergetic effects on tribological properties in terms of fade resistance, wear resistance and friction effectiveness. In particular, brass fibers played important roles in the friction stability by providing excellent thermal diffusivity at the friction interface. Potassium titanate whiskers showed excellent fade resistance and wear resistance compared to the substituted barite. Antimony trisulfide, on the other hand, showed little effect on the high temperature fade resistance and wear resistance, while it increased friction effectiveness at moderate temperatures. The friction materials without the three ingredients showed severe fade, indicating antisynergy effects.