• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1465-1469
• /
• 2003

In general satellite verification process, the AOCS (Attitude & Orbit Control Subsystem) should be verified through several kinds of verification test which can be divided into two major category like FBT (Fixed Bed Test) and polarity test. And each test performed in different levels such as ETB (Electrical Test Bed) and satellite level. The test method of FBT is to simulate satellite dynamics with sensors and actuators supported by necessary environmental models in ETB level. The VDS (Vehicle Dynamic Simulator) try to make the real situation as possible as the on-board processor will undergo after launch. The purpose of FBT test is to verify that attitude control logic function and hardware interface is designed as expected with closed loop simulation. The VDS is one of major equipments for performing FBT and consists of software and hardware parts. The VDS operates in VME environments with target board, several commercial boards and custom boards based on the VxWorks real time operating system. In order to make time synchronization between VDS and satellite on-board processor, high reliable semaphore was implemented to make synchronization with the interrupt signal from on-board processor. In this paper, the real-time operating environment used on VDS equipment is introduced, and the hardware and software configurations of VDS summarized in the systematic point of view. Also, we try to figure out the operational concept of VDS and AOCS verification test method with close-loop simulation.

• Laser Solutions
• /
• v.16 no.1
• /
• pp.10-14
• /
• 2013

Remote laser beam welding (RLW) has the benefits of high speed and high quality welding, especially as applied to automotive industry. RLW is designed in a way that end effecter and head of scanner move simultaneously, and require the compensation for the motion of end effecter in order to weld proper position. In this paper, we show the algorithms of RLW that enable the end effecter to synchronize with scanner based on time. The proposed method consists of two algorithms. These algorithms make it possible for the moving end effecter to weld on desired place. The effectiveness of the algorithms is shown by experiments.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.3
• /
• pp.293-299
• /
• 2010

The multiple block localization method in a wide area for multiple robots using iGS is proposed in this paper. The iGS is developed for the indoor global localization using ultrasonic and RF sensors. To measure the distance between a mobile robot and a beacon, the tag on the mobile robot wakes up one beacon to send out the ultrasonic signal and measures the traveling time from the beacon to the mobile robot. As the number of robots is increased, the sampling time of localization also becomes longer. Note that only one robot can localize its own position calling beacons one by one during each of the sampling interval. This is a severe constraint for the localization of multiple robots in a wide area. This paper proposes an efficient localization algorithm for the multiple robots in a wide area which can be divided into multiple blocks. For a given block, a master beacon is designated to synchronize robots. By the access of the synchronization signal, each beacon in the selected group sends out an ultrasonic signal. When the robots in the block receive the ultrasonic signal, they can calculate their own locations based on the distances to the beacons, which are obtained by the multiplication of flight time and velocity of the ultrasonic signal. The efficiency of the algorithm is verified through the real experiments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.12B
• /
• pp.1037-1041
• /
• 2004

In this paper we propose a new conceptual slave clock system in which remotely located clock is synchronized to the reference clock by intermediation of the satellite time, show a probability of adoption to real network by experiments. This new proposed method has lots of structural advantages over the existing methods because all of the node clocks can be maintained with the same hierarchical quality. The measurement results show that the accuracy of the experimental slave clock system can be kept within a few parts in 1012 and that the MTIE (Maximum Time Interval Error) meets the ITU-T Recommendation G.811 for the primary reference clock A prototype system having fully automatic operational functions has been realized, and it is expected to be commercially used as a node clock for synchronization in the digital communication network in the near future.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.1984-1986
• /
• 2001

In order to provided continuous solutions, latest developing navigation systems tend to integrate GPS receiver with INS or DR. Using the GPS carrier-phase measurements, an attitude GPS receiver with three antennas obtain the 3-dimensional attitude such as roll, pitch, and heading as well as position and velocity. With these angle measurements, in the attitude GPS/INS integrated system, attitude or gyro errors can be directly compensated. In this paper, we develop an integrated navigation system that combines attitude GPS receiver with INS. The performance of real-time integrated navigation system is determined by not only the implements of integration filter but also the synchronization of measurements. To meet these real-time requirements, the navigation software is implemented in multi-tasking structure in this paper. We also employ time-synchronization technique in the multi-sensor fusion. Experimental results show that the performance of the attitude GPS/INS integrated system is consistent even when cycle-slip occurs in carrier-phase measurements.

• Korean Journal of Remote Sensing
• /
• v.20 no.4
• /
• pp.227-234
• /
• 2004

The synchronization of Time Delay and Integration (TDI) against the temporal variation of osculating altitude in the operation of high resolution satellite imager was studied. The characteristics of osculating altitude variation was analyzed and its impact on the performance of TDI imger was also investigated. A practical ]me rate control method was proposed to compensate instantaneous TDI mismatch due to the osculating altitude variation, so that geometrical performance enhancement was achieved by the proposed method. This study is applicable to real satellite operation and can be useful for satellite image quality enhancement.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.2
• /
• pp.86-89
• /
• 2018

This paper introduces a ZigBee network-based four-lane lap time measurement system that can be set up for short-distance races. The instructions "Ready-Set-Go" can be announced at the entry point node when the start button is pushed, and foot switches installed at the exit point node can be stepped on by the runner for lap time measurement of the race. The start and exit point nodes are connected to a ZigBee network to communicate time synchronization packets. The exit point node maintains synchronized local time within 10 ms at most. The system does not need expensive measurement equipment and provides lap time recording in a more convenient manner than conventional lap time measurement methods.

• Journal of KIISE:Information Networking
• /
• v.35 no.2
• /
• pp.112-119
• /
• 2008

Today, A matter of concern of home network technology increase. The standard of communication between home network devices are required. IEEE 802.1 AVB(Audio/Video Bridging) specifies transmission method for time-sensitive data between these devices using Ethernet in bridged local area networks. IEEE 802.1 AVB and IEEE 1588 PTP(Precision Time Protocol) have various message type for grandmaster selection and synchronize the devices. These messages bring on complexity protocol. We propose a method that uses Single TimeSync frame in order to the problem. Our proposal is appropriate process complexity and low transmission delay for home network by using the TimeSync frame. Furthermore, after all devices are adjusted to the single TimeSync frame, a resource reservation, a forwarding and queueing rule are needed for a time-sensitive application.

• Journal of Positioning, Navigation, and Timing
• /
• v.13 no.1
• /
• pp.111-115
• /
• 2024

This study builds a machine learning model optimized for clocks among various techniques in the field of artificial intelligence and applies it to clock stabilization or synchronization technology based on atomic clock noise characteristics. In addition, the possibility of providing stable source clock data is confirmed through the characteristics of machine learning predicted values during holdover of atomic clocks. The proposed machine learning model is evaluated by comparing its performance with the AutoRegressive Integrated Moving Average (ARIMA) model, an existing statistical clock prediction model. From the results of the analysis, the prediction model proposed in this study (MSE: 9.47476) has a lower MSE value than the ARIMA model (MSE: 221.2622), which means that it provides more accurate predictions. The prediction accuracy is based on understanding the complex nature of data that changes over time and how well the model reflects this. The application of a machine learning prediction model can be seen as a way to overcome the limitations of the statistical-based ARIMA model in time series prediction and achieve improved prediction performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1069-1073
• /
• 2016

The Internet of Things (IoT) is the interconnection of uniquely identifiable embedded computing devices within the existing Internet infrastructure. IoT is expected to offer advanced connectivity of devices, systems, and services that goes beyond machine-to-machine communications and covers a variety of protocols, domains, and applications. Key system-level features that IoT needs to support can be summarized as device heterogeneity, scalability, ubiquitous data exchange through proximity wireless technologies, energy optimized solutions, localization and tracking capabilities, self-organization capabilities, semantic interoperability and data management, embedded security and privacy-preserving mechanisms. Time information is a critical piece of infrastructure for any distributed system. Time information and time synchronization are also fundamental building blocks in the IoT. The IoT requires new paradigms for combining time and data. This paper reviews conventional time keeping mechanisms in the Internet and presents issues to be considered for combining time and data in the IoT.