• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.39 no.3
• /
• pp.273-280
• /
• 1990

To prevent the shoot-through phenomena in a PWM inverter, a short dead time is usually provided between a pair of switching transistors in the same leg of the inverter. In this approach, the amount of the dead time is designed to meet the worst case condition of the inverter transistors and the base drive elements. So, in normal cases, relatively large portion of the dead time is unnecessary and it results in an undesirablecurrent waveform distortion and generates ripple torque on the motor shaft. In this paper, a new base drive method to remove the undesirable portion of the dead time is described. The method senses the transistor on/off states to interlock the other transistor of the leg without the external dead time. Also, for the transistors of large current rating, the Darlington drive circuit is combined to the proposed method and is tested to verify the effectiveness. The experimental results of the proposed method are described and compared with those of the conventional dead time method.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.11
• /
• pp.2011-2020
• /
• 1992

This paper discusses about real time control applying sliding mode to robot manipulators whose nonlinear terms, which are inertia term, Corilis term and centrifugal force mterm, are regarded as disturbances. We could simplify the dynamic equations of a manipulator and servo system, which are composed of linear elements and nonlinear elements, by assuming that non-linear terms are external disturbance. By simplifying that equation, we could easily obtain a control input which satisfy sliding mode. We proposed a new control input algorithm to decrease chattering in the application of sliding mode control of manipulator whose nonlinear elements are regarded as disturbances. We could take impulse response of linear elements of dynamic equations of a robot manipulator and servo system by Signal Compression Method. So then, we could obtain the unknown parametes of its linear lements, which are used to obtain switching parameter satisfying sliding mode, by Signal Compression Method. In this experiments, we used DSP(Digital Signal Processor) controller to suppress chattering by obtaining a switching speed and to carry out real time control.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.3
• /
• pp.51-58
• /
• 2008

This paper is a study of a prevention of power folding controller's thermal degradation. Power folding technology has been applied for many fields such as side rear vision mirror of vehicles, windshield wiper, antenna, power window. These controllers have been comprised with traditional DC moors, Switching electronic devices, and relays. But this methods have a limitation to overcome such problems of product reliability, endurance, noise margins. Therefore on this paper, to detect the movement of motor, sensing motor brush noise on a load sensing part has been used and controlling a precise RC timing control minimizes the thermal deterioration of motor. And using MOS FETs as a electronic switching device increases life-time and liability of control circuit. After testing such circuit and control method, repetition of operating time, cut-off time, wide operation voltage, power noise margin ware increased over eleven-fold.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.885-892
• /
• 2017

In this paper, we proposed a novel crowbar circuit for high-speed discharge charge switching to solve discharge charge-time delay of supply voltage in the conventional crowbar circuit. The proposed circuit is designed to increase the charge-speed after high-speed discharge of supply voltage, thereby reducing the time exposed to radiation damage and, the normal operation time of electronic system after passing the pulse radiation. The simulation of the discharge charge-times before the implement of the hardware is conducted using Cadence's pspice tool, and DUT (Device Under Test) board is fabricated in the device level. The comparison measurement of the crowbar circuits is performed on the satellite-electronic device for 24V. As the result, we confirmed the high-speed function of the proposed circuit by improvement of the discharge-speed 96.8% and the charge-speed 27.3% as compared with the conventional circuit.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.8B
• /
• pp.514-524
• /
• 2005

In optical burst switching(OBS) networks, the ingress edge router assembles packets in the same class queue into the appropriate size of burst. A burst control packet(BCP) is generated for channel reservation of corresponding data burst and sent earlier than the corresponding data burst with an offset time. Offset time is determined considering the number of hops from source to destination and the required quality of service(QoS). After offset time, the burst data is passed through tile pre-configured optical switches without any O/E/O conversion. But a failure in OBS networks may lead to the loss of bursts until the ingress nodes receive the failure indication signal. This results in a significant degradation in QoS. Therefore, in this paper, we propose a fault-tolerant node architecture based on sub-carrier multiplexing to reduce the effects of failure in OBS networks. The Performance of the proposed fault-tolerant node architecture exhibits considerable improvement as compared with the previous ones.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.8
• /
• pp.1-11
• /
• 2002

A multi-section DFB-LD shows optical bistability subject to externally injected light signal, then it has potential applications such as wavelength conversion and optical logic gates. In this paper, we have studied the optical bistability in multi-section DFB-LD using split-step time-domain model. It is confirmed that the multi-section DFB-LD, which is excited inhomogeneously, shows bistability. The optical bistable characteristics are investigated when input light is injected into a absorptive region. Simulation results show that multi-section DFB-LD works as a flip-flop depending on the set-reset optical pulse which has a few ns in switching time and a few pj in switching energy, so that it can act as a optical logic device. Besides, if we change the carrier lifetime and the differential gain coefficient, it is expected that the response time of optical output signal can be reduced.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.2
• /
• pp.19-25
• /
• 2008

When there are numerous wireless communication systems co-existing in the limited available frequency resource, an unexpected time delay can be caused during the system switching. So, in order to reduce this time delay, a mode selection method is required. In this paper, we propose a mode selection method to minimize the time delay for multi-system wireless communication systems. For the sake of efficiency, the mode selection method is designed by analyzing the preamble characteristics of different standards. Instead of performing a full search, we propose the preamble partial search to reduce the time delay to a minimum. Simulated with Matlab in an additive white Gaussian noise(AWGN) environment with a signal to noise ratio(SNR) of 10dB and bit error rate(BER) of $10^{-6}$, we evaluated and showed the performance improvement gained by using our proposed mode selection method.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.7 no.3
• /
• pp.196-208
• /
• 2007

An analytical model is proposed for an optically controlled Metal Semiconductor Field Effect Transistor (MESFET), known as Optical Field Effect Transistor (OPFET) considering the diffusion fabrication process. The electrical parameters such as threshold voltage, drain-source current, gate capacitances and switching response have been determined for the dark and various illuminated conditions. The Photovoltaic effect due to photogenerated carriers under illumination is shown to modulate the channel cross-section, which in turn significantly changes the threshold voltage, drainsource current, the gate capacitances and the device switching speed. The threshold voltage $V_T$ is reduced under optical illumination condition, which leads the device to change the device property from enhancement mode to depletion mode depending on photon impurity flux density. The resulting I-V characteristics show that the drain-source current IDS for different gate-source voltage $V_{gs}$ is significantly increased with optical illumination for photon flux densities of ${\Phi}=10^{15}\;and\;10^{17}/cm^2s$ compared to the dark condition. Further more, the drain-source current as a function of drain-source voltage $V_{DS}$ is evaluated to find the I-V characteristics for various pinch-off voltages $V_P$ for optimization of impurity flux density $Q_{Diff}$ by diffusion process. The resulting I-V characteristics also show that the diffusion process introduces less process-induced damage compared to ion implantation, which suffers from current reduction due to a large number of defects introduced by the ion implantation process. Further the results show significant increase in gate-source capacitance $C_{gs}$ and gate-drain capacitance $C_{gd}$ for optical illuminations, where the photo-induced voltage has a significant role on gate capacitances. The switching time ${\tau}$ of the OPFET device is computed for dark and illumination conditions. The switching time ${\tau}$ is greatly reduced by optical illumination and is also a function of device active layer thickness and corresponding impurity flux density $Q_{Diff}$. Thus it is shown that the diffusion process shows great potential for improvement of optoelectronic devices in quantum efficiency and other performance areas.

• Journal of Information Technology Applications and Management
• /
• v.26 no.4
• /
• pp.51-69
• /
• 2019

One of the most considerate phenomena of the era of the Fourth Industrial Revolution is the use of digital devices. Digitalization is rapidly advancing through all areas of industry and life. Customer journey with digitalization is looking totally different from previous customer journey. The research targets were users of fashion, automobiles, cosmetics and online shopping malls. We analyzed 300 people for each valid questionnaire. The results of the study are as follows. First, it has been proven that digital experience affects positive (+) impact on purchasing intention and positive (+) impact on recommending intention and negative impact (-) on switching intent and subsequently affects positive impact (+) to purchase and incase of switching intent, negative impact (-) to purchase. Unlike traditional methods such as SPC(Service Profit Chain), the Digital experience to Purchase process Chain (DPC) has been identified to be suitable in the digital age. Second, the digital satisfied group (5 score-very satisfaction) has shown same result as above. However the digital neutral group (even though 4 score- satisfaction in five-point scale), specially in a highly competitive industry, has different from the satisfied group and 3 score-normal is same as dissatisfied group. It means that this group is that If there is a high level of attractiveness of substitute goods, there is a high possibility of switching them. It has supported Jones and Sasser [1995] that there have been two types of loyalty of true long-term loyalty and what we call false loyalty in the highly competitive industry zone which is commoditization or low differentiation, many substitutes, low cost of switching. Identifying true loyalty and false loyalty is crucial to establishing a customer experience strategy. it is necessary to actively utilize long-term digital experiences strategy to increase the total satisfaction of digital experience through all of customer purchasing journey in order to enhance the digital customer experience. It is difficult to see the effect as a one-time event. It should be scaled over the entire customer purchase process over a long period of time, which can positively affect purchase intention, recommendation intention, and conversion intention. This is also why it is difficult for second-runners to overtake first-runners in a short period.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.205-208
• /
• 2004

The switching mechanism of multi-domain vertical alignment mode LCD and delayed on response time phenomenon in special conditions are investigated. A modified DCC (Dynamic Capacitance Compensation), DCCII has been developed for the fast response time performance in PVA TFT-LCD TVs. DCCII applies a pre-tilt voltage to addressed pixels during the previous frame in addition to an overshoot voltage. In result, the response time less than 8 msec, has been obtained for all moving images through the DCCII technique.