• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.10
• /
• pp.19-24
• /
• 1995

The majority of problems to which FDTD is being applied involve open structure which require the appropriate scheme to terminate the computational domain. In particular, for the propagation problem of the outgoing waves, a certain type of boundary condition needs to be applied on outer boundaries of the computational domain to generate no reflected waves. In this paper, a new simple technique is presented, which allows the reduced computation time and excellent absorbing characteristics for normal and oblique incident waves on outer boundaries. To illustrate the validity of this method, a numerical calculation for monopole antenna is carried out and the results are compared to measured data. The time-domain properties for circular patch antennas are investicated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.217-222
• /
• 2004

In this paper, the efficient channel estimation schemes for DRM system(AM band digital radio broadcasting standard) are investigated. In frequency domain, by means of the linear interpolation, the second order interpolation, cubic spline interpolation, and time domain interpolation, the channel impulse response is estimated respectively to compensate the attenuation due to the fading. And in time domain, the frequency channel impulse response is averaged to reduce the attenuation due to the AWGN. By the simulation, the performance of MSE, BER and the complexity of calculation is compared and analyzed for each interpolation scheme.

• Journal of Mechanical Science and Technology
• /
• v.15 no.2
• /
• pp.232-238
• /
• 2001

Fast Fourier Transformation is employed to convert the head variation of a pipeline in the time domain to the amplitude of the frequency domain. Applying method of characteristics to a pipeline provides a significant frequency range for a surge introduced from the valve modulation. Inverse Fast Fourier Transformation and a Finite Impulse Response Filter can be used to remove any possible noise existing from the significant frequency range of an unsteady condition. A filtered signal shows higher potential for the inverse calculation of leakage detection than the noise-added signal does. The respective performances of Inverse Fast Fourier Transformation and a Finite Impulse Response Filter are compared in terms of leakage detection capability. Characteristics of the frequency range for multiple leakages were investigated to validate the effectiveness of the noise control method in the frequency domain.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.2
• /
• pp.115-123
• /
• 2017

Electrochemical noise signals in many cases exhibit a DC drift that should be removed prior to further data analysis. Polynomial fitting and moving average removal method have been used to remove trends of electrochemical noise (EN) in time domain. The corrosion inhibition of synthesized schiff base N,N'-bis(3,5-dihydroxyacetophenone)-2,2-dimethylpropandiimine on API-5L-X70 steel in hydrochloric acid solutions were used to study the effects of drifts removal methods on noise resistance calculation. Also, electrochemical impedance spectroscopy (EIS) was used to study the corrosion inhibition property of the inhibitor. The results showed that for the calculation of $R_n$, both methods were effective in trend removal and the polynomial with m=4 and MAR with p=40 were in agreement.

• Korean Journal of Optics and Photonics
• /
• v.12 no.6
• /
• pp.479-484
• /
• 2001

The analysis of photonic band gaps and anomalous dispersion phenomena in photonic crystals requires understanding of band structures and dispersion surfaces. We show the results of the calculation of band structures and dispersion surfaces for a few two- dimensional lattices, using the finite-difference time-domain method with periodic boundary conditions. In addition, localized defect modes the exist within the band gap are computed by the same method.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.3
• /
• pp.323-338
• /
• 2022

Heat generation and temperature of a battery is usually presented by an equation of current. This means that we need to adopt time domain calculation to obtain thermal characteristics of the battery. To avoid the complicated calculations using time domain, 'state of charge (SOC)' can be used as an independent variable. A SOC based calculation method is elucidated through the comparison between the calculated results and experimental results together. Experiments are carried for rapid resistive discharge of a large-capacitive lithium secondary battery to evaluate variations of cell potential, current and temperature. Calculations are performed based on open-circuit cell potential (SOC,T), internal resistance (SOC,T) and entropy (SOC) with specific heat capacity.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.8
• /
• pp.1497-1504
• /
• 2009

This Paper Propose a method to reduce the calculation time in JPEG2000. That is, if a coefficient is estimate a upper-level subband and its descendents skip the scan process. There is a trade-off relationship between the calculation time and the image quality or the amount of output data, the calculation time and the amount of output data decreases, but the image degradation increases. The experimental results showed that in calculation time was 35% in average, which means that ls ge ses. The ein calculation time and output data can be obtls ed with a cost of an acceptlble image quality degradation.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1884-1893
• /
• 2016

The ride-through control of a doubly-fed induction generator (DFIG) for the voltage sags on wind farms utilizing crowbar circuits by which the rotor side converter (RSC) is disabled has being reported in many literatures. An analysis and calculation of the transient current when the RSC is switched off are of significance for carrying out the low voltage ride through (LVRT) of a DFIG. The mathematical derivation is highlighted in this paper. The zero-state and zero-input responses of the transient current in the frequency domain through a Laplace transformation are investigated, and the transient components in the time domain are achieved. With the characteristics worked out from the linear resolving without modeling simplification, the selection of the resistance in the linear crowbar circuit and the value conversion from a linear circuit to a nonlinear one is proposed to setup the attenuation rate. In terms of grid code requirements, the theoretical analysis for the time constant of the transient components attenuation insures the controllability when the excitation of the RSC is resumed and it guarantees the reserved time for the response of the reactive power compensation. Simulations are executed in MATLAB/SIMPOWER and experiments are carried out to validate the theoretical analysis. They indicate that the calculation method is effective for selection of the resistance in a crowbar circuit for LVRT operations.

• Journal of the Society of Naval Architects of Korea
• /
• v.53 no.6
• /
• pp.514-520
• /
• 2016

Oil and gas production riser systems need to be designed considering a wide band quarter-modal analysis which contains low-, wave-, VIV(Vortex induced vibration) frequencies. The VIV can be separated into cross-flow(CF) and in-line(IL) components. In this study, the various idealized tri- and quarter-modal spectra are suggested to analyze fatigue damage on the production riser system. In order to evaluate the fatigue damage increment caused by the IL's motion, tri- and quarter-modal spectral fatigue damages are calculated in time domain. And the fatigue damage calculated from two different modal spectra are compared quantitatively. Then the suitability of existent wide band fatigue damage models for quarter modal spectrum was evaluated by comparison of frequency domain calculation and time domain calculation. The result show that although spectral density of IL motion is not remarkable in quantity, the effect on the fatigue damage is significant and existent fatigue damage models are not adequately estimating damage by quarter-modal spectra.

• International Journal of Railway
• /
• v.7 no.4
• /
• pp.109-116
• /
• 2014

For optimization of a low-noise track system, rail vibration and noise radiation needs to be investigated. The main influencing parameters for the noise radiation and the quantitative results of every track system can be obtained using a calculation model of generation and radiation of railway noise. This kind of model includes contact modeling and the calculation model of the dynamic properties of the wheel and the rail. This study used a nonlinear wheel/rail interaction model in the time domain to investigate the excitation of the rolling noise. Wheel/rail response is determined by time integrating Green's function of the rail together with force impulses from the wheel/rail contact. This model and the results of the study can be used for supporting calculation with the conventional model by an addition of the contributions due to nonlinearities to the roughness spectrum.