• 한국산업융합학회 논문집
• /
• 제25권6_2호
• /
• pp.993-1002
• /
• 2022

This paper relates to a method of modeling the thrust dynamic load caused by the thrust variation occurring on the blade due to the tower shadow below the rated wind speed. A method that uses thrust coefficient is presented by introducing "tower shadow coefficient of thrust variation". For a 2MW wind turbine, the values of "tower shadow coefficient of thrust variation" are calculated and analyzed at wind speeds below the rated. The dynamic load model of thrust under tower shadow is evaluated in Matlab/Simulink using the obtained "tower shadow coefficient of thrust variation" and thrust coefficient. It shows that the thrust variations acting on the three blades by the tower shadow can be expressed using both the thrust coefficient and the introduced "tower shadow coefficient of thrust variation".

• 한국추진공학회지
• /
• 제8권4호
• /
• pp.9-15
• /
• 2004

지상연소시험 후 측정된 추력은 시험대의 동특성으로 인해 실제 추력과는 달리 과도진동이 중첩되어 왜곡된 형태를 나타낼 수 있다. 본 연구에서는 왜곡된 추력을 보상하기 위해 측정된 추력만을 이용해 로켓모터의 실제 추력을 계산하는 방법을 제안하였고, 제안한 방법을 실험을 통해서 얻은 데이터에 적용하여 타당성을 입증하였다. 먼저 시험대 운동방정식을 이산시간 데이터 해석에 적합하도록 차분식으로 근사시키고, 시험대 특성 파라메타를 대수감소율 방법을 이용해 추정하였다. 그리고 측정추력과 추정한 시험대 파라메타 정보를 이용하여 시험대 변위를 계산한 후 차분식에 적용하여 실제추력을 계산하였다. 결과, 측정된 추력 이외에 다른 물리량을 측정하지 않고서 단지 측정된 추력 데이터만을 이용하더라도 시험대 과도응답이 제거된 실제 추력을 계산할 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.572-582
• /
• 2017

공기 흡입 엔진을 개발하기 위해서는 지상 시험을 통한 추력 측정이 반드시 필요한데, 공기 흡입 엔진은 추력 측정 장치에서 측정된 값 이외에도 엔진 흡입구로 들어오는 공기 유동에 의한 힘을 고려하여 총추력을 계산해야 한다. 또한 다분력 추력 측정 장치를 활용하여 요와 피치 방향의 측추력도 정확하게 측정하고 분석할 수 있어야 한다. 래버린스 씰 격리, 1축 총추력 계산, 다분력 추력 측정 장치 개발, 측추력 분석 등의 일련 과정을 통해 공기 흡입 엔진의 총추력을 정밀하게 추정하여 엔진 성능을 보다 정확하게 평가할 수 있게 하였다.

• 한국항공우주학회지
• /
• 제31권5호
• /
• pp.93-99
• /
• 2003

극초음속 추진기관의 설계 및 평가에 있어 추력의 측정은 매우 중요하다. 일반적인 추력 측정방법으로는 추력 측정기를 사용하고 있지만 이러한 방법으론 엔진의 자유제트 실험이나 모델 연소기 같은 실험에는 적용이 부적절하다. 이 때문에 피토압력을 이용한 새로운 추력 계산 방법을 고려하였고 검증하였다. 피토 압력을 통해 계산된 추력의 검증은 추력측정기를 통해 측정된 실제 추력값과의 비료를 통해 이루어질 수 있으며 이를 위해 추력측정기 위에 소형 초음속 풍동을 장착하였다. 추력이 측정되는 동안 충동 후방의 피토압력을 동시에 측정하였다. 측정된 피토 압력을 이용하여 구한 추력값을 검증하기 위해서, 추력측정기로 측정한 추력을 완정팽창 노즐이론 및 추력계수를 이용한 이론적인 계산에 의해 구해진 추력값과 비료, 분석하였다.

• 한국정밀공학회지
• /
• 제15권8호
• /
• pp.183-192
• /
• 1998

In this paper, we measure the back-EMF and the thrust of a linear brushless DC motor along the relative position between coils and magnets in various speed environments in order to obtain the back-EMF and the thrust as a function of a motor position. The measured back-EMF function and thrust function of the position differ from the analytical ones within 5%. The measured back-EMF and thrust function can, then, be employed in controlling the thrust ripple of the linear motor. Furthermore, to minimize the torque ripple of the linear motor, we suggest the design method to shape the back-EMF and thrust function of the linear motor.

• 한국유체기계학회 논문집
• /
• 제9권5호
• /
• pp.7-13
• /
• 2006

In the present study, we develop an analysis module to be applicable to design of sliding thrust bearings. The pressure equation is solved by using the finite element method. Average lubricant temperature is obtained from using the energy balance method. The module developed has been applied to three types of thrust bearing, such as tapered-land thrust bearings of angular and diamond types, and tilting-pad thrust bearings. Effects of the dam of the tapered-lad thrust bearings have also been investigated. It has been seen that the tapered-land thrust bearings of angular type result in the highest load capacity, while the tilting pad thrust bearings result in the lowest lubricant temperature. It has also been seen that the dam in the tapered-land thrust bearings increases both the load capacity and lubricant temperature.

• 한국추진공학회지
• /
• 제8권2호
• /
• pp.73-84
• /
• 2004

로켓모터의 성능을 확인하기 위해 지상에서 연소시험을 수행하여 추력, 압력, 온도. 그리고 변형률 등 필요한 데이터를 계측하지만 측정된 추력은 시험대 동특성으로 인해 실제 추력과는 달리 과도진동이 포함된 왜곡된 형태를 나타낼 수 있다. 이러한 경우에는 추력 최대치나 추력 상승시간 등 로켓모터의 성능을 결정하는 값들의 정확한 값을 얻지 못할 수 있다. 따라서 본 논문에서는 이러한 추력 왜곡 현상의 원인을 분석하고 그 문제점을 해결하기 위한 이론적인 방법을 제안한다. 또한 제안된 방법을 가상 시험대에 적용하여 제안한 방법의 적용 가능성을 확인하고, 차후 실험 데이터를 이용한 추력 추정의 기본적인 방향을 제시하고자 한다.

• Journal of Biosystems Engineering
• /
• 제25권1호
• /
• pp.1-10
• /
• 2000

This study was conducted to develop the mathmatical model for predicting the side thrust which is generated by the shearing action on the vertical surfaces of the sides of the track. Experiments were conducted with the three different shear plates with grouser length of 1, 3 and 5 cm for two different soil condition using soil bin system. The measured side thrust were compared with the values predicted by the new model developed in this study and by Bekker's model respectively. The values of side thrust predicted by the new model were more close to the measured values than those of the side thrust predicted by Bekker's model . The total thrust measured were also compared with the values predicted by the conventional model which considers only bottom thrust effect and by the new model which contains not only bottom thurst but side thrust effect. The values of the thrust predicted by conventional modelwere lower than measured values for both of the soil conditions and the three levels of grouser length. The maximum errors of conventional model were increased with the increase of grouser length. but the values of the total thrust predicted by the model developed in this study were well matched to the measured ones for both of the soil conditions and the three levels of grouser lengths.

• International Journal of Fluid Machinery and Systems
• /
• 제8권1호
• /
• pp.46-54
• /
• 2015

Thrust-ring-pump is a kind of extreme-low specific speed centrifugal pump with special structure as numerous restrictions from thrust bearing and operation conditions of hydro-generator units. Because the oil circulatory and cooling system with thrust-ring-pump has a lot of advantages in maintenance and compactness in structure, it has widely been used in large and medium-sized hydro-generator units. Since the diameter and the speed of the thrust ring is limited by the generator set, the matching relationship between the flow passage inside the thrust ring (equivalent to impeller) and oil bath (equivalent to volute) has great influence on hydrodynamic performance of thrust-ring-pump. On another hand, the head and flow rate are varying with the operation conditions of hydro-generator units and the oil circulatory and cooling system. As so far, the empirical calculation method is employed during the actual engineering design, in order to guarantee the operating performance of the oil circulatory and cooling system with thrust-ring-pump at different conditions, a collaborative hydrodynamic design and optimization is purposed in this paper. Firstly, the head and flow rate at different conditions are decided by 1D flow numerical simulation of the oil circulatory and cooling system. Secondly, the flow passages of thrust-ring-pump are empirically designed under the restrictions of diameter and the speed of the thrust ring according to the head and flow rate from the simulation. Thirdly, the flow passage geometry matching optimization between thrust ring and oil bath is implemented by means of 3D flow simulation and performance prediction. Then, the pumps and the oil circulatory and cooling system are collaborative hydrodynamic optimized with predicted head-flow rate curve and the efficiency-flow rate curve of thrust-ring-pump. The presented methodology has been adopted by DFEM in design process of thrust-ring-pump and it shown can effectively improve the performance of whole system.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.363-368
• /
• 2004

Due to various advantages over the conventional linear motion device such as ball-screw, linear motors have been used in wide variety of industrial applications for years. Driven by increased demand for precision machine tools, the importance of high positioning accuracy, high stiffness and high thrust are greatly increasing. The merits of linear motor are high speed, high acceleration and good positioning accurcy. In addition, Linear motor for high quality machine tool call for high thrust, high stiffness. In this paper, thrust ripple, detent force and thermal behavior are considered for the development of high performance linear motor whose thrust is up to 10,000N. This paper presents a comprehensive study for an iron core type linear motor characteristics that include the influence of PM position on thrust, thrust ripple by detent force and motor dynamics as well.