• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.8
• /
• pp.481-485
• /
• 2015

We investigated the effects of annealing on the electrical and thermal properties of ZTO/4H-SiC heterojunction diodes. A ZTO thin film layer was grown on p-type 4H-SiC substrate by using solution process. The ZTO/SiC heterojunction structures annealed at $500^{\circ}C$ show that $I_{on}/I_{off}$ increases from ${\sim}5.13{\times}10^7$ to ${\sim}1.11{\times}10^9$ owing to the increased electron concentration of ZTO layer as confirmed by capacitance-voltage characteristics. In addition, the electrical characterization of ZTO/SiC heterojunction has been carried out in the temperature range of 300~500 K. When the measurement temperature increased from 300 K to 500 K, the reverse current variation of annealed device is higher than as-grown device, which is related to barrier height in the ZTO/SiC interface. It is shown that annealing process is possible to control the electrical characteristics of ZTO/SiC heterojunction diode.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.5
• /
• pp.253-256
• /
• 2017

A thin Te interlayer was applied to a Ni/n-InGaAs contact to reduce the contact resistance between Ni-InGaAs and n-InGaAs. A 5-nm-thick Te layer was first deposited on a Si-doped n-type $In_{0.53}Ga_{0.47}As$ layer, followed by in situ deposition of a 30-nm-thick Ni film. After the formation of the Ni-InGaAs alloy by rapid thermal annealing at $300^{\circ}C$ for 30 s, the extracted specific contact resistivity (${\rho}_c$) reduced by more than one order of magnitude from $2.86{\times}10^{-4}{\Omega}{\cdot}cm^2$ to $8.98{\times}10^{-6}{\Omega}{\cdot}cm^2$ than that of the reference sample. A thinner Ni-InGaAs alloy layer with a better morphology was obtained by the introduction of the Te layer. The improved interface morphology and the graded Ni-InGaAs layer formed at the interface were believed to be responsible for ${\rho}_c$ reduction.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.56-58
• /
• 2006

본 논문은 PVD(Physical Vapor Deposition)의 마그네트론 스퍼터(Magnetron sputter) 박막코팅(Thin film coating) 공정에서 플라즈마(Plasma)를 발생시키고 제어하는 DC 전원공급 장치에 관한 것이다. 이 논문에서는 임피던스의 변화가 심하고 아크(Arc)가 빈번히 발생하는 플라즈마 부하의 특성에 대해, 과도상태(Transient state)의 출력제어 성능을 향상시키고 아크 발생 시 부하로 전가되는 아크에너지를 저감시키기 위한 직류 전원 공급 장치에 대해 소개한다. 전원장치는 수하특성을 가지며 플라즈마 부하에 적합한 출력 제어성을 확보하고 아크 에너지를 최소화하기 위해 고주파 L-C 직렬공진회로 기법을 적용한다. 개발된 DC 20kW급 전원 장치는 인버터와 고주파 절연변압기, 정류기로 구성된다. 인버터는 $100{\sim}200kHz$의 제어주파수로 PFM 및 PWM 제어를 하며, 단위용량 5kW급 컨버터 4개를 직, 병렬 연결하여 출력리플을 최소화 하였다. 개발된 장치의 우수한 제어성능은 실제 플라즈마 공정에서 시험 평가한 결과를 통해 검증할 수 있었다.

• Journal of Information Display
• /
• v.10 no.4
• /
• pp.202-205
• /
• 2009

An automated circuit repair system was developed for enhancing the yield of nondefective liquid crystal panels, focusing on the resist patterns on the circuit material layer of thin-film transistor (TFT) substrates prior to etching. The developed system has an advantage over the parallel conventional system: In the former, the repair conditions depend on the type of resist whereas in the latter, the repair parameters must be fine-tuned for each circuit material. The developed system consists of a resist pattern defect inspection system and a pattern repair system for short and open defects. The repair system performs fine corrections of abnormal areas of the resist pattern. The open-repair system is equipped with a syringe to dispense resist. To maintain a stable resist diameter, a thermal insulator was installed in the syringe system. As a result, the diameter of the dispensed resist became much more stable than when no thermal insulator was used. The resist diameter was kept within the target of $400{\pm}100{\mu}m$. Furthermore, a prototype system was constructed, and using a dummy pattern, it was confirmed that the system worked automatically and correctly.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.6
• /
• pp.234-240
• /
• 2005

In this study, ion nitriding of a EHA pump part made of AISI 4340 steel was performed under different applied power conditions to study the relationship between dimensional changes of specimens and the type of applied power source. Microstructures and micohardness distribution at different processing conditions were also examined. Duplex surface treatment of ion nitriding with the optimum process conditions to produce the minimum dimensional variation in a EHA pump part and a TiN thin film coating by unbalanced magnetron sputtering was performed and the specimens with a duplex surface treatment were subjected to a high speed wear test to evaluate the wear performance of EHA hydraulic pump parts with various surface treatment conditions. Results indicated that uniform and continuous surface layer with a minimum dimensional variation could be obtained by ion nitriding with bipolar mode power source and much enhanced wear characteristics with a duplex surface treatment could be obtained, compared with results from ion nitriding or single-layerd TiN coating specimens.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.6
• /
• pp.250-254
• /
• 2011

NiO-AZO films were deposited on glass substrate by DC and RF magnetron co-sputtering system in pure $O_2$ gas without substrate heating during deposition. In order to control the chemical composition of the film, NiO target was supplied with constant RF power of 150 W and AZO target (doped with 2.98 at% aluminum) with DC power varied between 40 W to 80 W. Deposited NiO-AZO films were evaluated by structural and chemical analysis. With introducing AZO, XRD and XPS data reveal that NiO were supplied with more oxygen. these results could be strongly affected by the higher bond enthalpy of NiO compared to ZnO, which makes it possible for NiO to obtain excessive oxygen from ZnO.

• Korea-Australia Rheology Journal
• /
• v.19 no.3
• /
• pp.165-169
• /
• 2007

The light guide plate (LGP) of LCD-BLU (Liquid Crystal Display-Back Light Unit) is usually manufactured by forming numerous dots by etching process. However, the surface of those etched dots of LGP is very rough due to the characteristics of etching process, so that its light loss is relatively high due to the dispersion of light. Accordingly, there is a limit in raising the luminance of LCD-BLU. In order to overcome the limit of current etched-dot patterned LGP, micro-lens pattern was tested to investigate the possibility of replacing etched pattern in the present study. The micro-lens pattern fabricated by the modified LiGA with thermal reflow process was applied to the optical design of LGP. The attention was paid to the effects of different optical pattern type (i.e. etched dot, micro-lens). Finally, the micro-lens patterned LGP showed better optical qualities than the one made by the etched-dot patterned LGP in luminance.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.252-252
• /
• 2011

최근 주목받고 있는 amorphous gallium-indium-zinc-oxide (a-GIZO) thin film transistors (TFTs)는 수소가 첨가된 비정질 실리콘 TFT에 비해 높은 이동도와 뛰어난 전기적, 광학적 특성에 의해 큰 주목을 받고 있다. 또한 넓은 밴드갭을 가지므로 가시광 영역에서 투명한 특성을 보이고, 플라스틱 기판 위에서 구부러지는 성질에 의해 플랫 패널 디스플레이나 능동 유기 발광소자 (AM-OLED), 투명 디스플레이에 응용되고 있다. 뿐만 아니라, 일반적인 Poly-Si TFT는 자체적으로 가지는 결정성에 의해 대면적화 시 균일성이 좋지 못하지만 GIZO는 비정질상 이기 때문에 백플레인의 대면적화에 유리하다는 장점이 있다. 이러한 TFT를 제작하기 전, 전기적 특성에 대한 정보를 얻거나 예측하는 것이 중요한데, 이에 따라 고안된 구조가 바로 metal point contact FET (pseudo FET)이다. pseudo FET은 소스/드레인 전극을 따로 증착할 필요 없이 채널을 증착한 후, 프로브 탐침을 채널의 표면에 적당한 압력으로 접촉시켜 전하를 공급하는 소스와 드레인처럼 동작시킬 수 있다. 따라서 소스/드레인을 증착하거나 lithography와 같은 추가적인 공정을 요구하지 않아 소자의 특성을 보다 간단하고 수월하게 분석할 수 있다는 장점이 있다. 본 연구에서는 p-type 기판위에 100nm의 oxidation SiO2를 게이트 절연막으로 사용하는 a-GIZO pseudo FET를 제작하였다. 소자 제작 후, 열처리 온도에 따른 전기적 특성을 분석하였고, 열처리 조건은 30분간 N2 분위기에서 실시하였다. 열처리 후 전기적 특성 분성 결과, 450oC에서 가장 낮은 subthreshold swing 값과 게이트 전압의 더블 스윕 후 문턱 전압의 변화가 거의 없음을 확인하였다.

• Journal of Sensor Science and Technology
• /
• v.4 no.3
• /
• pp.15-21
• /
• 1995

In this paper, $TiO_{2}-V_{2}O_{5}$ humidity sensors are fabricated by Sol-Gel method. For the establishment of optimum processing condition which is good humidity sensitive characteristics for specimens, their microstructures and crystalline-structures are analysed. Grain size increases with substitution rate of $V^{5+}$ on $Ti^{4+}$ site. From the analysis of XRD, $V^{5+}$ peak can't confirm with $V_{2}O_{5}$ rate. Their humidity sensitive characteristics is good at 1mol% of $V_{2}O_{5}$ rate and heat-treated at $700^{\circ}C$. The capacitance of specimens decreases with frequency.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.48 no.3
• /
• pp.209-214
• /
• 1999

This paper deals with the effects of activation process of MgO thin film on the dielectric characteristics of surface discharge type AC PDP. The discharge voltage decreased with increase in the MgO activation time and temperature until $400^{\circ}C$ under the condition of clean high vacuum. However, for the sample activated above $430^{\circ}C$ the discharge voltage increased. These results may be explained by the MgO morphology change and surface cleaning in the process of activation.