• Journal of the Korean institute of surface engineering
• /
• v.53 no.6
• /
• pp.312-321
• /
• 2020

Morphology of porous cobalt electro-deposits was systematically investigated as functions of cobalt precursors in the plating bath and applied cathodic current density with a special focus on cobalt nano-rod formation. It was proved that the concentration of cobalt precursor plays little effect on the morphology of cobalt electro-deposits at relatively low plating current density while it significantly affects the morphology with increasing plating current density. Such a dependence was discussed in terms of the kinetics of two competitive reactions of cobalt reduction and hydrogen evolution. Cobalt nano-rod structure was created at specific ranges of cobalt precursor content and applied cathodic current density, and its diameter and length varied with plating time without notable formation of side branches which is usually found during dendrite formation. Specifically, the nano-rod length was preferentially increased in relative short plating time (<15 s), resulting in higher aspect ratio of nano-rod with plating time. Whereas, both the nano-rod length and diameter were increased nearly at the same level in a prolonged plating time, making the aspect ratio unchanged. From the analysis of crystal structure, it was confirmed that the cobalt nano-rod preferentially grew in the form of single crystal on a dense poly-crystalline cobalt thin film initially formed on the substrate.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.7
• /
• pp.1426-1437
• /
• 2002

Using the Lagrangian explicit time-integration finite element code NET3D which can treat three-dimensional high-velocity impact problems, oblique penetration processes of long rod projectile with yaw against thin plate are simulated. Through the comparison of simulation result with experimental result and other code's computational result, the adaptability and accuracy of NET3D is evaluated under the complex situation in which yaw angle and oblique angle exist simultaneously. Main research contents to be handled in this paper include the followings. First, the accuracy and efficiency estimation of NET3D code result obtained from the oblique penetration simulations of long rod projectile with yaw against thin plate. Second, the effect of increasing impact velocity. Third, the effect of initial yaw for the spaced-plate target. Residual velocities, residual lengths, angular velocities, and final deformed configurations obtained from the NET3D computations are compared with the experimental results and other code's computational results such as Eulerian code MESA and Lagrangian code EPIC. As a result of comparisons, it has been found that NET3D code is superior to EPIC code and MESA code in the prediction capability of residual velocity and residual length of penetrator. The key features obtained from the experiment can be successfully reproduced through NET3D simulations. Throughout the study, the applicability and accuracy of NET3D as a metallic armor system design tool is verified.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.338.2-338.2
• /
• 2016

Al doped ZnO (AZO) thin films were deposited on Si substrates with rod-shaped-surface by pulsed laser deposition method (PLD). Si-rods were prepared through chemical etching. To analyze the influence on the formation of the rod structure, samples with various chemical etching conditions such as AgNO3/HF ratio, etching time, and solution temperature were prepared. The morphology of Si-rod structures were examined by FE-SEM. Fig. 1 shows a typical structure of n-AZO/p-Si-rod juncions. The fabricated n-AZO/p-Si-rod devices exhibited p-n diode current-voltage characteristics. We compared the I-V characteristics of n-AZO/p-Si-rod devices with the samples without Si-rod structure.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.4
• /
• pp.849-859
• /
• 2013

This paper proposes a real-time simulation technique for thin rods undergoing large rotational deformation. Rods are thin objects such as ropes and hairs that can be abstracted as one-dimensional structures. Development of a real-time physical model that can produce visually convincing animation of thin rods has been a challenging problem in computer graphics. We adopt continuum mechanics to formulate the governing equation, and develop a modal warping technique for rods to integrate the governing equation in real-time; This is a novel extension of the previous modal warping techniques developed for solids and shells. Experimental results show that the proposed method runs in real-time even for large meshes and it can simulate large bending and/or twisting deformations.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.409-410
• /
• 2002

In order to measure the oil-film pressure in sliding surface of machinery, we have developed a piezo-resistive type thin-film pressure sensor. To reduce the measurement error due to temperature and strain, the constituent of the pressure sensitive alloy was optimized and a new sensor shape was devised. In this study, we present the measurement results of the oil-film pressure distribution in engine connecting rod big-end bearing and piston pin- bosses with 3 different pin-boss shapes using the newly developed thin-film pressure sensor.

• Macromolecular Research
• /
• v.9 no.1
• /
• pp.1-19
• /
• 2001

Poly(p-phenylene pyromellitimide) and poly(4,4'-biphenylene pyromellitimide) are representatives of fully rod-like polyimides. Their structure and properties in thin films are reviewed. The polymers exhibit some excellent properties such as high molecular packing coefficient, high mechanical modulus, and low thermal expansion coefficient, and low interfacial stress, so that they are very attractive to both industry and academia. However, these polymers are very brittle and thus practically useless. Some chemical modifications to improve such drawback with a little sacrifice of the high modulus are described: i) incorporation of short side groups into the polymer backbone and ii) insertion of proper linkages into the polymer backbone.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.475-475
• /
• 2013

Cuprous oxide ($Cu_2O$)는 밴드갭이 2.17 eV p-type 산화물 반도체로써 태양에너지 변환기, photocatalysis (광촉매작용), 센서, 스위칭 메모리 등 응용이 다양한 재료이다. 산화물 반도체의 기본 특성은 나노/마이크로 범위 안에서 재료의 표면형태, 크기, 구조와 형상 공간방향등에 크게 영향을 받는다. 그렇기 때문에 원하는 $Cu_2O$ 특성을 얻기 위해서 성장 거동을 아는 것은 매우 중요하다. RF 마그네트론 스퍼터법으로 rod 성장 사례는 잘 알려지지 않았다. 그래서 RF 마그네트론 스퍼터법 $Cu_2O$ rod 형성 실험을 통하여 $Cu_2O$ 형성과 성장 거동을 알아보았다. RF 마그네트론 스퍼터법으로 $Cu_2O$ rod를 glass 기판 위에 Cu metal target을 이용하여 형성시켰다. $Cu_2O$ rod 합성을 위해 기판온도 및 산소분압 O2/(Ar+O2)=3%, 5%, 7% 증착시간 등을 변화시켜 실험하였다. 성장된 rod의 분석은 XRD, SEM으로 확인하였다. 성장 거동은 증착온도와 증착시간에 차이를 보였다. 증착온도 $550^{\circ}C$에서 rod가 생성되는 것을 관찰하였다. 증착시간이 길어질수록 rod 길이가 길어지고 일정 시간이 지나면 rod의 길이 성장보다는 두께(폭)가 성장하는 것을 확인하였다. 증착온도 $550^{\circ}C$ 그리고 산소분압 3%, 5%, 7% 조건에서 rod 합성 실험을 하였을 때 3%, 5% 조건에서 rod의 성장을 확인하였다. 이때 3%, 5% 산소분압에 따라 rod의 모양이 변화하였다. 하지만 7% 조건에서는 rod가 성장하지 않았다. 이유는 3%, 5%에서는 Cu metal peak을 확인하였지만, 7% 조건에서는 Cu metal peak이 없었다. 이로부터 Cu metal이 $Cu_2O$ rod 생성에 영향을 미치는 중요한 요소임을 예상할 수 있었다.

• Nuclear Engineering and Technology
• /
• v.29 no.2
• /
• pp.175-180
• /
• 1997

It has been known that eater-side corrosion of fuel rods in nuclear reactor is accompanied with the metallic loss of wall thickness and hydrogen pickup in the fuel dadding tube. The fuel dad corrosion is one of the major factors to be controlled to maintain the fuel integrity during reactor operation. An oxide later thickness measuring device equipped with ECT probe system was developed by KAERI, and whose performance test was carried out in NDT(Non-destructive Test) hot-cell or PIE(Post Irradiation Examination) Facility. At first, the calibration/performance test was executed for the unirradiated standard specimen rod fabricated with several kinds of plastic thin films whose thickness ore predetermined, and the result of which showed a good precision within 10% of discrepancy. And then, hot test us peformed for the irradiated fuel rod selectively extracted from J44 fuel assembly discharged from Kori Unit-2. The data obtained with this device were compared with the metallographic result obtained from destructive examination in PIEF hot-cell on the same fuel rod to verify the validity of the measurement data.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.680-686
• /
• 1995

It has been known that water-side corrosion of fuel rods in nuclear reactor is accompanied with the loss of metallic wall thickness and pickup of hydrogen. This corrosion is one of the important limiting factors ill the operating life of fuel rods. In connection with the fuel cladding corrosion, a device to measure the water-side oxide layer thickness by means of the eddy-current method without destructing the fuel rod was developed by KAERI. The device was installed on the multi-function testing bench in the nondestructive test hot-cell and its calibration was carried out successfully for the standard rod attached with plastic thin films whose thicknesses are predetermined. It shows good precision within about 10% error. And a PWR fuel rod, one of the J-44 assembly discharged from Kori nuclear power plant Unit-2, has been selected for oxide layer thickness measurements. With the result of data analysis, it appeared that the oxide layer thicknesses of Zircaloy cladding vary with the length of the fuel rod, and their thicknesses were compared with those of the destructive test results to confirm the real thicknesses.

• Korean Journal of Materials Research
• /
• v.17 no.5
• /
• pp.273-277
• /
• 2007

Vertically aligned Zinc Oxide rod arrays were grown by the self-assembly hydrothermal process on the GaN epitaxial layer which has a same lattice structure with ZnO. Zinc nitrate and DETA solutions are used in the hydrothermal process. The $(HfO_2)$ thin film was deposited on GaN and the patterning was made by the photolithography technique. The selective growth of ZnO rod was achieved with the patterned GaN substrate. The fabricated ZnO rods are single crystal, and have grown along hexagonal c-axis direction of (002) which is the same growth orientation of GaN epitaxial layer. The density and the size of ZnO rod can be controlled by the pattern. The optical property of ordered array of vertical ZnO rods will be discussed in the present work.