• 반도체디스플레이기술학회지
• /
• 제9권3호
• /
• pp.75-78
• /
• 2010

In this study we investigated the electrical properties of ZnO-based MOS capacitor with $HfO_2$ as the gate dielectric. MIM capacitor, which uses either $HfO_2$ or $Al_2O_3$ as the dielectric layer, is also studied to understand the dependency of the dielectrics on the preparation conditions. It was found that thinner $HfO_2$ films yield better electrical properties, namely lower leakage current and higher breakdown electric field. These properties were observed to deteriorate when subsequently annealed. Capacitance in the depletion region of MOS capacitor was found to increase with UV ozone treatment time up to 60min. However, when the treatment time was extended to 120min, the trend is reversed. The 'threshold voltage' was also observed to positively shift with UV ozone treatment time up to 60min. The shift apparently saturated for longer treatment.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권8호
• /
• pp.340-346
• /
• 2002

Capacitor material utilized in the downsizing passive devices and integration of passive devices requires the physical and electrical properties at given area such as capacitor thickness reduction, relative dielectric constant increase, low leakage current and thermal stability. common capacitor materials, $Al_2O_3$, $SiO_2$, $Si_3N_4$, $SiO_2$/$Si_3N_4$, TaN and et al., used until recently have reached their physical limits in their application to integration of passive devices. $Ta_2O_{5}$ is known to be a good alternative to the existing materials for the capacitor application because of its high dielectric constant (25~35), low leakage current and high breakdown strength. Despite the numerous investigations of $Ta_2O_{5}$ material, there have little been established the clear understanding of the annealing effect on capacitance characteristic and conduction mechanism. This study presents the dielectric properties $Ta_2O_{5}$ MIM capacitor structure Processed by $O_2$ RTA oxidation. X-ray diffraction patterns showed the existence of amorphous phase in $600^{\circ}C$ annealing under the $O_2$ RTA and the formation of preferentially oriented-$Ta_2O_{5}$ in 650, $700^{\circ}C$ annealing and the AES depth profile showed $O_2$ RTA oxidation effect gives rise to the $O_2$ deficientd into the new layer. The leakage current density respectively, at 3~1l$\times$$10_{-2}$(kV/cm) were $10_{-3}$~$10_{-6}$(A/$\textrm{cm}^2$). In addition, behavior is stable irrespective of applied electric field. the frequency vs capacitance characteristic enhanced stability more then $Ta_2O_{5}$ thin films obtained by $O_2$ reactive sputtering. The capacitance vs voltage measurement that, Vfb(flat-band voltage) was increase dependance on the $O_2$ RTA oxidation temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 논문집
• /
• pp.3-5
• /
• 2008

The $SrBi_2Ta_2O_9$ thin films are deposited on Pt-coated electrode(Pt/$TiO_2/SiO_2$/Si) using RF magnetron sputtering method. The ferroelectric properties of SBT capacitors with annealing temperatures were studied. Through the x-ray diffraction analysis and the scanning electron microscopy (SEM), it could be observed that crystallization of the SBT thin film started around $650^{\circ}C$ and complete crystallization was accomplished around $750^{\circ}C$ and grains grew from a small spheric form to rod-like. For the leakage current density of the SBT capacitor depending upon various annealing atmospheres, capacitor annealed in the oxygen atmosphere showed the most excellent characteristic, and they were respectively about $2.13\times10^{-9}[A/cm^2]$ at 5V and 340.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.155-158
• /
• 1998

MLS capacitor with lipid ultra thin films were deposited by Langmuir-Blodgett (LB) method on the sillicon wafer. The current versus voltage and capacitance versus voltage relationships are depend on the applied voltage, electrode area and electrode materials. LB films deposited were made of L-$\alpha$-DLPC, the 1 layer's thickness of 35$\AA$ was measured by ellipsometer. And MLS capacitor with different electrode materials, the work function of these materials was investigated to increase the leakage current. The result indicated the lower leakage current and very high saturation value of capacitance was reached within 700-800 pF when the two electrode was Ag. And $\varepsilon$$_1$, $\varepsilon$$_2$ versus photon energy showed good film formation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.247-248
• /
• 2006

Carbon nitride films were evaluated that they had many advantages for miniature micro-humidity-sensors using the standard CMOS technology humidity sensing properties and CV characteristics of the carbon nitride films have been investigated for fabricating one chip HUSFET(Humidity Sensitive Field Effect Transistor) humidity sensors Carbon nitride films were deposited on silicon substrate with meshed electrodes by reactive RF magnetron sputtering system. The capacitor-type humidity sensor revealed good humidity-impedance characteristics with a wide range of relative humidity changes, decreasing $254k{\Omega}$ to $16k{\Omega}$ according to increase of relative humidity between 5% ~ 95% and the films were very stable on the Si wafer. These results reveal that $CN_x$ thin films can be used for Si based or HUSFET structure one chip micro-humidity sensors.

• 한국진공학회지
• /
• 제4권S1호
• /
• pp.145-150
• /
• 1995

PZT thin films were fabricated on Pt/Ti/SiO2/Si substrates at $500^{\circ}C$ by ECR-PECVD for the application to the charge storage capacitor of ULSI DRAMs. Perovskite single phase PZT films were obtained by controling the film compositional ratio Pb/(Zr+Ti) close to 1. The anion concentrations in the PZT films were successfully controlled by adjusting the flow rates of each MO sources. Capacitance of a typical 94 nm thick PZT film prepared at $500^{\circ}C$ in this work was about 5.3 uF/$\textrm{cm}^2$, which corresponds to the equivalent SiO2 thickness of 0.65nm.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(2)
• /
• pp.24-27
• /
• 2000

Ferroelectric P $b_{0.99}$〔(Z $r_{0.6}$S $n_{0.4}$)$_{0.9}$ $Ti_{0.1}$〕$_{0.98}$N $b_{0.02}$ $O_3$(PNZST) thin films were deposited by a RF magnetron sputtering on (L $a_{0.5}$S $r_{0.5}$)Co $O_3$(LSCO)/Pt/Ti/ $SiO_2$/Si substrate using a PNZST target with excess PbO of 10 mole％. The thin films deposited at the substrate temperature of 500 $^{\circ}C$ were crystallized to a perovskite phase after rapid thermal annealing(RTA) The thin films annealed at 650 $^{\circ}C$ for 10 seconds in air exhibited the good crystal structures and ferroelectric properties. The remanent polarization and coercive field of the PNZST capacitor were about 20 $\mu$C/$\textrm{cm}^2$ and 50 kV/cm, respectively. The reduction of the polarization after 2.2$\times$10$^{9}$ switching cycles was less than 10 ％.0 ％.％.0 ％.0 ％.

• 한국전기전자재료학회논문지
• /
• 제13권12호
• /
• pp.996-1002
• /
• 2000

Ferroelectric (Ba, Sr) TiO$_3$(BST) thin films have attracted much attention for use in new capacitor materials of dynamic random access memories (DRAMs). In order to apply BST to the DRAMs, the etching process for BST thin film with high etch rate and vertical profile must be developed. However, the former studies have the problem of low etch rate. In this study, in order to increase the etch rate, BST thin films were etched with a magnetically enhanced inductively coupled plasma(MEICP) that have much higher plasma density than RIE (reactive ion etching) and ICP (inductively coupled plasma). Experiment was done by varying the etching parameters such as CF$_4$/(CF$_4$+Ar) gas mixing ratio, rf power, dc bias voltage and chamber pressure. The maximum etch rate of the BST films was 170nm/min under CF$_4$/CF$_4$+Ar) of 0.1, 600 W/-350 V and 5 mTorr. The selectivities of BST to Pt and PR were 0.6 and 0.7, respectively. Chemical reaction and residue of the etched surface were investigated with X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS).

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.362-365
• /
• 2002

Hf thin films were deposited on bottom metal using a RF magnetron sputtering method followed by oxidation and annealing in O$_2$ and N$_2$ ambient, respectively. Various top metal electrodes (i.e., Al, Au, and Cu) were deposited by evaporation, and their roles on physical and electrical properties were investigated. Using the XRD, SEM and AFM techniques, we confirmed that the grain size of HfO$_2$ thin films enlarges as a function of oxidation temperature, increasing dielectric constant. However, other electrical properties (e.g., tan) deteriorateas a consequence. The dielectric constant and tan of HfO$_2$ thin films oxidized at 500 $^{\circ}C$ were 17-25 and 3${\times}$10-3 - 2x10-2, respectively, in the frequency range of 1 Hz to 1 MHz. The leakage current density was less than 1${\times}$10-8A/cm2 up to 0.7 MV/cm. In addition, electrical properties of HfO$_2$ thin films (e.g., the dielectric constant, leakage current and tan $\delta$) depend on top metal electrode. We showed that Al top metal electrode results in the best result.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.402-405
• /
• 1999

The Study of this paper is to establish the optimum fabricating condition of specimens using Vapor Deposition Polymerization Method which belongs to a mode of preparation of functional organic thin films with dry process and to develop thin film type humidity sensor which has good humidity sensitive Characteristics. Scanning electron microscopy Atomic force microscopy were used to analyze the characteristics of thin film and the basic structure of the humidity sensor is a parallel capacitor which consists of three layers of Al/PI/Al. The characteristics of fabricated samples were measured under various conditions and obtained linear characteristics in the range of 20∼80%RH independent of temperature change and low hysteresis characteristics.