• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.240.2-240.2
• /
• 2013

The device scale of flash memory was confronted with quantum mechanical limitation. The next generation memory device will be required a break-through for the device scaling problem. Especially, graphene is one of important materials to overcome scaling and operation problem for the memory device, because ofthe high carrier mobility, the mechanicalflexibility, the one atomic layer thick and versatile chemistry. We demonstrate the hybrid memory consisted with the metal-oxide quantum dots and the mono-layered graphene which was transferred to $SiO_2$ (5 nm)/Si substrate. The 5-nm thick secondary $SiO_2$ layer was deposited on the mono-layered graphene by using ultra-high vacuum sputtering system which base pressure is about $1{\times}10^{-10}$ Torr. The $In_2O_3$ quantum dots were distributed on the secondary $SiO_2$2 layer after chemical reaction between deposited In layer and polyamic acid layer through soft baking at $125^{\circ}C$ for 30 min and curing process at $400^{\circ}C$ for 1 hr by using the furnace in $N_2$ ambient. The memory devices with the $In_2O_3$ quantum dots on graphene monolayer between $SiO_2$ thin films have demonstrated and evaluated for the application of next generation nonvolatile memory device. We will discuss the electrical properties to understating memory effect related with quantum mechanical transport between the $In_2O_3$ quantum dots and the Fermi level of graphene layer.

• Journal of the Korean Home Economics Association
• /
• v.11 no.4
• /
• pp.363-373
• /
• 1973

The Sewability was tested with the seam strength and Puckering Grade by a general sewing machine according to some properties of simulated Leather, yarn tensile strength needle and stitches. The main results tested are as follows ; 1. The thick and uncomfortable leather is unable to be sewed by a general sewing machine, but the thin and soft one is able to. 2. The interval between stitches depends on type of leather used, and the variance in accordance with type of leather varies much more in the case of narrower interval. 3. When the sewability of leather-surface is not so good, is desirable to pour oil on the surface for the purpose of better efficiency. 4. The seam strength is directly proportional to interval of stitch and tensile strength of yarn and leather used, and needle No. 14 is more effective than No.1l. 5. The more the soft and thin leather is, the lower the Puckering Grade becomes. Type of yarn and interval of stitches do not seem to effect the Puckering Grade.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.12
• /
• pp.984-989
• /
• 2012

We have investigated the structural, electrical and optical properties of Ga-doped ZnO (GZO) thin films prepared by RF magnetron sputtering with laboratory-made ZnO targets containing 1, 3, 5, 7 wt% of $Ga_2O_3$ powder as a doping source. The GZO thin films show the typical crystallographic orientation with c-axis regardless of $Ga_2O_3$ content in the targets. The $3,000{\AA}$ thick GZO thin films with the lowest resistivity of $7{\times}10^{-4}{\Omega}{\cdot}cm$ are obtained by using the GZO ($Ga_2O_3$= 5 wt%) target. Optical transmittance of all films shows higher than 80% at the visible region. The optical energy band gap for GZO films increases as the carrier concentration ($n_e$) in the film increases.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.597-600
• /
• 2006

The silver gate and source/drain electrodes for an a-Si thin film transistor were fabricated by the selective electroless plating (SELP) process. Relevant physical properties including taper angle, uniformity and resistivity are investigated. The Ag layer was about 150nm to 250nm thick, the resistivity less than $3{\times}10^{-6}$ Ohm-cm and the taper angle 45'-60' and the nonuniformity less than 10% on G2 substrates. The transfer characteristics with the Ag gate, and source/drain electrodes respectively possessed good field effect mobility similar to conventionally fabricated a-Si TFTs. This process provided low resistivity, low cost and ease of processing.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.115-117
• /
• 2009

Interface dipole energies between interfacial layers with different thicknesses coated on indium tin oxides (ITOs) and 4,4'-bis[N-(1-naphtyl)-N-phenyl-amino]biphenyl are determined. After $O_2$ plasma treatment on thick-metal (>4 nm) coated ITO, the work function and interface dipole energy increased. In thin-metal (< 2 nm) coated ITO, no change in the interface dipole energy was found though the work function increased. Thus, the $O_2$ plasma treated thin (< 2 nm) interfacial layer reduced the hole injection barrier.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.1
• /
• pp.35.1-35.1
• /
• 2011

The solar X-ray telescopes, the Yohkoh SXT and the Hinode XRT, have observed for a couple of decades a variety of coronal structures in the range of wide field-of-view (FOV) covering the full solar disk. It has been emphasized that the optical structure of solar telescopes should be designed with care for improving the uniformity over the full FOV. The vignetting effect is one of the important optical characteristics for describing the performance of a telescope, which reflects the ability of collecting the incoming light at different locations and different photon energies. The correction of this vignetting effect would be an important calibration step that should be performed in advance, especially when the observed images are to be used for photometric purposes. Since the vignetting effect of solar X-ray telescopes shows wavelength dependence, a special care should be taken when, for example, performing the temperature analyses with thin and thick filters for flaring activities observed at the periphery of the full FOV. The results of analysis of pre-launch calibration data for the evaluation of vignetting effect will be introduced in detail.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.186-186
• /
• 2015

We have introduced multifunctional ITO single thin films formed by normal sputtering system equipped with a plasma limiter which effectively blocks the bombardment of energetic negative oxygen ions. MFSS ITO also possesses high gas diffusion barrier properties simultaneously low resistivity even it deposited at room temperature without post annealing on plastic substrate. Nano-crystalline enhancement by Ar energy has energy window from 20 to 30 eV under blocking NOI condition. Effect of blocking NOI and optimal Ar energy window enhancement facilitate that resistivity is minimized to $3.61{\times}10^{-4}{\Omega}cm$ and the WVTR of 100 nm thick MFSS ITO is $3.9{\times}10^{-3}g/(m^2day)$ which is measured under environmental conditions of 90% relative humidity and 50oC that corresponds to a value of ${\sim}10^{-5}g/(m^2day)$ at room temperature. The multifunctional MFSS ITO with low resistivity, and low gas permeability will be highly valuable for plastic electronics applications.

• Journal of the Korean Society of Combustion
• /
• v.10 no.2
• /
• pp.9-17
• /
• 2005

WSGGM with gray gas regrouping is successfully applied to study the flame structure of opposed flow flames including effect of radiative transfer. The statistical narrow band model is used to obtain the benchmark solutions. Results obtained by using the optically thin model are shown to overestimate the emission and to predict the flame structures inadequately especially for optically thick and low stretch rate flames. Computed results by using the WSGGM with 10 gray gases and SNB model show reasonable agreements with each other, and the required calculation time for the WSGGM is acceptable for engineering applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.196.1-196.1
• /
• 2016

TCO(Transparent Conducting Oxide) on flat glass is used in thin-film photovoltaic cell, flat-panel display. Nowadays, Corning(R) Willow Glass(R), known as flexible substrate, has attracted much attention due to its many advantages such as reliable roll-to-roll glass processing, high-quality flexible electronic devices, high temperature process. Also, it can be an alternative to flexible polymer substrates which have their poor stability and degradation of electrical and optical qualities. For application on willow glass, the flexibility, electrical, optical properties can be greatly influenced by the TCO thin film thickness due to the inherent characterization of thin film in nanoscale. It can be expected that while thick TCO layer causes poor transparency, its sheet resistance become low. Also, rarely reports were focusing on the influence of flexible properties by varying TCO thickness on flexible glass. Therefore, it is very important to optimize TCO thickness on flexible Willow glass. In this study, Ti-ZnO thin films, with different thickness varied from 0 nm to 50 nm, were deposited on the flexible willow glass by atomic layer deposition (ALD). The flexible, electrical and optical properties were investigated, respectively. Also, these properties of Ti-doped ZnO thin films were compared with un-doped ZnO thin film. Based on the results, when Ti-ZnO thin films thickness increased, resistivity decreased and then saturated; transmittance decreased. The Figure of Merit (FoM) and flexibility was the highest when Ti-ZnO thickness was 40nm. The flexible, electrical and optical properties of Ti-ZnO thin films were better than ZnO thin film at the same thickness.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.1
• /
• pp.34-47
• /
• 1996

Veneers of two nominal thicknesses, 1.5 and 2.5mm, were rotary peeled from Japanese larch (Larix leptolepis). Dahurian larch (Larix gmelinei) and Radiata pine (Pinus radiata) bolts unheated and heated in the water vat temperature of $66^{\circ}C$ by rising a final temperature at 10cm core of $60^{\circ}C$ to remain core diameter of 11.4cm. 1.5 and 2.5mm thick veneer cut from the heated Japanese larch were significantly thinner than those of the unheated bolt and 2.5mm thick veneer cut from the heated Dahurian larch were significantly thicker than that of the unheated bolt. 1.5mm thick Dahurian larch veneer and 1.5 and 2.5mm thick Radiata pine veneers showed insignificant difference between the unheated and heated bolts, respectively. Check distance on the loose side of 1.5mm thick veneer cut from the heated Radiata pine was significantly wider than that of the unheated bolt. However check distances on the loose side of 1.5 and 2.5mm thick Japanese larch and Dahurian larch veneers and 2.5mm thick Radiata pine veneers showed insignificant difference between the unheated and heated bolts. Also the depth of check on the loose side of three species showed insignificantly difference between the unheated and heated bolts. Arithmatic mean deviation($R_a$) and maximum height($R_{max}$) of the profile on the loose side of dried veneer by preheating the bolt compared with unheated bolts were different among apecies and between veneer thickness. The preheating treatment slightly affected qualities of these thin veneers such as 1.5 and 2.5mm. The yield of 2.5mm thick veneer from the heated radiata pine was significantly higher than that of the unheated bolt. However the yield of 2.5mm thick veneer for other two species and 1.5mm thick veneer for three species showed insignificant difference between the unheated and heated bolts. The yield of 2.5mm thick veneer for three species were higher than those of 1.5mm thick veneer. The average yields of green veneer of Japanese larch. Dahurian larch and Radiata pine were 57.1, 55.1 and 54.0 percent, respectively. Variables such as initial MC. drying time and veneer thickness had strong effect for Japanese larch veneer, less effect for Radiata pine veneer and nuch less effect on final MC for Dahurian larch veneer in jet drying. Correlation between the current MC and the drying time of Dahurian larch with low variation of initial MC was higher than those of Japanese larch and Radiata pine veneer with high variation of initial MC in high temperature drying. Thickness shrinkages of 2.5mm thick veneer for Japanese larch and Radiata pine were higher than those of 1.5mm thick veneers, but shrinkages of Dahurian larch veneer were similar between two nominal veneer thicknesses.