• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.6
• /
• pp.893-901
• /
• 2002

Effect of boundary layer thickness on the flow characteristics around a rectangular prism has been investigated by using a PIV(Particle Image Velocimetry) technique. Three different boundary layers(thick, medium and thin)were generated in the Atmospheric Boundary Layer Wind Tunnel at Pusan National University. The thick boundary layer having 670 mm thickness was generated by using spires and roughness elements. The medium thickness of boundary layer($\delta$=270 mm) was the natural turbulent boundary layer at the test section floor with fairly long developing length(18 m). The thin boundary layer($\delta$=36.5 mm) was generated on the smooth panel elevated 70cm from the wind tunnel floor. The Reynolds number based on the free stream velocity(3 ㎧) and the height of the model(40 mm) was 7.9$\times$10$^3$. The mean velocity vector fields and turbulent kinetic energy distributions were measured and compared. The effect of boundary layer thickness was clearly observed not only in the length of separation bubble but also in the location of reattachment point. The thinner the boundary layer thickness, the higher the turbulent kinetic energy Peak around the model roofbecame. It is strongly recommended that the height ratio between the model and the approaching boundary layer thickness should be encountered as a major parameter.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.5
• /
• pp.347-350
• /
• 2013

By inserting a very thin metal layer of Ag between two outer oxide layers of amorphous silicon indium zinc oxide (SIZO), we fabricated a highly transparent SIZO/Ag/SIZO multilayer on a glass substrate. In order to find the optimized thickness of Ag layers, we investigated the variation of optical properties depending on Ag thickness. It was found that the transition of Ag layer from island formation to a continuous film occurred at a critical thickness. Continuity of the Ag film is very important for optical properties in SIZO/Ag/SIZO multilayer. With about 15 nm thick Ag layer, the multilayer showed a high optical transmittance of 80% at 550 nm and low emissivity in IR.

• Journal of Ocean Engineering and Technology
• /
• v.29 no.2
• /
• pp.163-168
• /
• 2015

This paper presents the results of experimental work on the wedge slamming impact problem. An experiment was done with a wedge model. The deadrise angle of the wedge was $4^{\circ}$. The model was made in two parts: the outside part was made of a 5-mm-thick steel plate that could be assumed to be a rigid body, and the inside part was made of a thin SUS plate that could be assumed to be an elastic body. Thin SUS plate thicknesses of 2 mm and 3 mm were used to determine the effect of plate rigidity. The drop height was varied from 0.25 m to 1 m to determine the effect of a large deformation.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.27-34
• /
• 2017

We investigated the feasibility of parylene F usage as an intermediate layer between a polydimethylsiloxane (PDMS) substrate and an Au thin-film interconnect as well as the swelling effect of PDMS substrate on the stretchable deformability of an Au thin film. The 150-nm-thick Au film, which was sputtered on a PDMS substrate without a parylene F layer, exhibited an initial resistance of $11.7{\Omega}$ and an overflow of its resistance at a tensile strain of 12.5%. On the other hand, the Au film, which was formed with a 150-nm-thick parylene F layer, revealed an much improved resistance characteristics: $1.21{\Omega}$ as its initial resistance and $246{\Omega}$ at its 30% elongation state. With swelling of PDMS substrate, the resistance of an Au film substantially decreased to $14.4{\Omega}$ at 30% tensile strain.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1281-1282
• /
• 2007

Effect of tension coating on reducing iron losses of thin grain-oriented 3% Si-Fe steel sheets was investigated. Conventional grain-oriented electrical steel sheets have a forsterite coating layer and a tension coating layer in order to apply tensile stress to the rolling direction of the sheets. However the proposed coating method in this paper is to form only a tension coating layer on the both surfaces of the sheets. Iron losses with the tension coating were reduced by 8% under the condition of 1.7 T and 60 Hz. Consequently the proposed tension coating is applicable to $80{\mu}m$-thick 3% Si-Fe steel sheets.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.8
• /
• pp.474-478
• /
• 2017

We report on thin-film transistors based on $TiO_x$ pre-annealed by femtosecond laser pulses. A 30-nm thick $TiO_x$ active channel layer was initially deposited by an ALD system. The $TiO_x$ semiconducting films were annealed by irradiation with a femtosecond laser (power: $3W/cm^2$) for 5, 25, and 50s. Atomic force microscopy images revealed that the surface of a $TiO_x$ film without femtosecond laser pre-annealing was relatively rough, while after annealing with femtosecond laser pulses, the surface of the $TiO_x$ films became smooth. With increasing radiation time, the surrounding gas atmosphere could have a larger impact on the $TiO_x$ surface; meanwhile, the thin-film roughness decreased. Thin-film transistors with $TiO_x$ active channels pre-annealed at 50s exhibited good transfer characteristics and an on-to-off current ratio of ${\sim}10^3$.

• Korean Journal of Materials Research
• /
• v.23 no.3
• /
• pp.161-167
• /
• 2013

The ZnO thin films were grown on GaN template substrates by RF magnetron sputtering at different RF powers and n-ZnO/p-GaN heterojunction LEDs were fabricated to investigate the effect of the RF power on the characteristics of the n-ZnO/p-GaN LEDs. For the growth of the ZnO thin films, the substrate temperature was kept constant at $200^{\circ}C$ and the RF power was varied within the range of 200 to 500W at different growth times to deposit films of 100 nm thick. The electrical, optical and structural properties of ZnO thin films were investigated by ellipsometry, X-ray diffraction (XRD), atomic force microscopy (AFM), photoluminescence (PL) and by assessing the Hall effect. The characteristics of the n-ZnO/p-GaN LEDs were evaluated by current-voltage (I-V) and electroluminescence (EL) measurements. ZnO thin films were grown with a preferred c-axis orientation along the (0002) plane. The XRD peaks shifted to low angles and the surface roughness became non-uniform with an increase in the RF power. Also, the PL emission peak was red-shifted. The carrier density and the mobility decreased with the RF power. For the n-ZnO/p-GaN LED, the forward current at 20 V decreased and the threshold voltage increased with the RF power. The EL emission peak was observed at approximately 435 nm and the luminescence intensity decreased. Consequently, the crystallinity of the ZnO thin films grown with RF sputtering powers were improved. However, excess Zn affected the structural, electrical and optical properties of the ZnO thin films when the optimal RF power was exceeded. This excess RF power will degrade the characteristics of light emitting devices.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.6
• /
• pp.350-355
• /
• 2014

Bottom-gate tin oxide ($SnO_2$) thin film transistors (TFTs) were fabricated on $N^+$ Si wafers used as gate electrodes. 60-nm-thick $SnO_2$ thin films acting as active layers were sputtered on $SiO_2/Al_2O_3$ films. The $SiO_2/Al_2O_3$ films deposited on the Si wafers were employed for gate dielectrics. In order to increase the resistivity of the $SnO_2$ thin films, oxygen mixed with argon was introduced into the chamber during the sputtering. The mobility of $SnO_2$ TFTs was measured as a function of the flow ratio of oxygen to argon ($O_2/Ar$). The mobility variation with $O_2/Ar$ was analyzed through studies on crystallinity, oxygen binding state, optical properties. X-ray diffraction (XRD) and XPS (X-ray photoelectron spectroscopy) were carried out to observe the crystallinity and oxygen binding state of $SnO_2$ films. The mobility decreased with increasing $O_2/Ar$. It was found that the decrease of the mobility is mainly due to the decrease in the polarizability of $SnO_2$ films.

• Korean Journal of Plant Resources
• /
• v.7 no.2
• /
• pp.143-147
• /
• 1994

The experiment was carried out to study the influence of planting densities and on some agronomic characters and yield of rresh weight in Agastache rugoso. The results obtained are summarized as fol-lows; stem length was long in dense planing and short in spacious Planting. Stem diameter was thickIn spacious planting, and was thin in dense planting. Yield was higher in dense planting densities (20x20cm : 2spiants/m, 30$\times$20cm : 17plants/m).

• Fashion & Textile Research Journal
• /
• v.10 no.6
• /
• pp.955-965
• /
• 2008

This study used the method that measure the participants' responds on the experiment, and the measurement means is a survey. The primary factor plan is $5{\times}2{\times}3{\times}2$. The independent variable are neckline(5), trousers or skirt style(2), somatotype(3), culture(2), and the dependant variables are physical visual effect and the favor of clothe design. In cases of Korean, thin somatotype had better were V-neckline suit for looking shoulders wide because they have too narrow shoulders, and were pants suit than skirt suit for looking pelvis major. thin somatotype person who wants to look tall should wear china collar or tailored collar suit with pants. If she wears round neckline suit with skirt, the lower part of body and the height look tall. Pants suit with V neckline and skirt suit with china collar make standard somatotype looked having wide shoulders. Standard somatotype person with wide shoulder should avoid this style. The size of waist and pelvis was looked thick in round neckline and was looked thin in V neckline. So it will be better to find the right suit for one's weakness. Obesity had better wear V neckline to look neck slim and not wear stand and tailored collar. When obesity person wears pants suit, she is looked having slim waist than skirt suit. In case of American, thin somatotype in pants suit looks much taller than in skirt suit when she wears round neckline and stand collar suit. Standard somatotype has no difference because it is the basic shapes. Generally, it goes with all kinds of suit design. The belly and pelvis of American's obesity look fatter and bigger than Korean's obesity. The same with Korean, round neckline suit makes obesity looked belly and pelvis fat and big.