• Membrane and Water Treatment
• /
• 제11권2호
• /
• pp.97-109
• /
• 2020

Membrane fouling is the main drawback of membrane technology. Frequent membrane cleaning and membrane replacement are, therefore, required to reduce membrane fouling that causes permeate flux reduction, lower rejection, or higher operating pressure. Studies have proved that the alteration of membrane properties is the key controlling factor in lessening membrane fouling. Among stimuli-responsive membranes, thermo-responsive membrane is the most popular, with a drastic phase transition and swelling-shrinking behavior caused by the temperature change. In this study, the thermo-responsive ability of two commercial membranes, PolyCera® Titan membrane and PolyCera® Hydro membrane, at different temperatures was studied on the antifouling function of the membrane in palm oil mill effluent (POME) treatment. The evaluation of the membrane's thermo-responsive ability was done through three cycles of adsorption (fouling) and desorption (defouling) processes in a membrane filtration process. The experimental result depicted that PolyCera® Hydro membrane had a higher membrane permeability of 67.869 L/㎡.h.bar than PolyCera® Titan membrane at 46.011 L/㎡.h.bar. However, the high membrane permeability of PolyCera® Hydro membrane was compensated with low removal efficiency. PolyCera® Titan membrane with a smaller mean pore size had better rejection performance than PolyCera® Hydro membrane for all tested parameters. On the other hand, PolyCera® Titan membrane had a better hydrodynamic cleaning efficiency than PolyCera® Hydro membrane regardless of the hydrodynamic cleaning temperature. The best hydrodynamic cleaning performed by PolyCera® Titan membrane was at 35℃ with the flux recovery ratio (FRR) of 99.17 ± 1.43%. The excellent thermo-responsive properties of the PolyCera® Titan membrane could eventually reduce the frequency of membrane replacement and lessen the use of chemicals for membrane cleaning. This outstanding exploration helps to provide a solution to the chemical industry and membrane technology bottleneck, which is the membrane fouling, thus reducing the operating cost incurred by the membrane fouling.

• Elastomers and Composites
• /
• 제50권1호
• /
• pp.30-34
• /
• 2015

Thermo-mechanical treatment process of a compressed open-cell rigid polyurethane foam (OC-RPUF), which was fabricated for the vacuum insulation panel (VIP), was studied to obtain an optimum condition for the dimensional stability by the relaxation of compressive stress. Thermo-mechanical deformation of the sample OC-RPUF was shown to occur from about $120^{\circ}C$. Yield stress of 0.36 MPa was shown at about 10% yield strain. And, densification of the foam started to occur from 75% compressive strain and could be continued up to max. 90%. Compression set of the sample restored after initial compression to 90% at room temperature was ca. 82%. Though the expansion occurred to about twice of the originally compressed thickness in case of temperature rise to $130^{\circ}C$, it could be overcome and the dimensional stability could be maintained if the constant load of 0.3 MPa was applied. As the result, a thermo-mechanical treatment process, i.e, annealing process at temperature of $130{\sim}140^{\circ}C$ for about 20 min as is the maximum compressed state at room temperature, should be required for dimensional stability as an optimum condition for the use of VIP core material.

• 대한금속재료학회지
• /
• 제49권9호
• /
• pp.692-698
• /
• 2011

The thermo-chemical treatment (TCT) process was applied to achieve surface hardening of CP titanium. The following three different surface modification conditions were tested so that the best surface hardening process could be selected:(a) PVD, (b) TCT+PVD, and (c) TCT+Aging+PVD. These specimens were tested and analyzed in terms of surface roughness, wear, friction coefficient, and the gradient of hardening from the surface of the matrix. The three test conditions were all beneficial to improve the surface hardness of CP titanium. Moreover, the TCT treated specimens, that is, (b) and (c), showed significantly improved surface hardness and low friction coefficients through the thickness up to $100{\mu}m$. This is due to the functionally gradient hardened surface improvement by the diffused interstitial elements. The hardened surface also showed improvement in bonding between the PVD and TCT surface, and this leads to improvement in wear resistance. However, TCT after aging treatment did not show much improvement in surface properties compared to TCT only. For the best surface hardening on CP titanium, TCT+PVD has advantages in surface durability and economics.

• 한국재료학회지
• /
• 제5권5호
• /
• pp.620-624
• /
• 1995

To study the acid and base properties of chemical-treated natural zeolite, FT-IR analysis was performed by the adsorption of pyridne and pyrrole and thermo-gravimetric analysis was done by the adsorption of NH$_{3}$. These solid catalysts have two acid sites, which are related to the Bronsted and Lewis acid sites, respectively. HIC-treatment led to the increased acidity and the maintained basicity.Acidity of NaHO-treatment samples also increased with thr NaOH-treatment but basicity decreased. The p-xylene selectivity on the chemical-treatment zelite was higher than that on the untreated zeolite.

• 유기물자원화
• /
• 제30권4호
• /
• pp.27-40
• /
• 2022

본 연구에서는, 탈수슬러지 및 음식물류폐기물의 효율적인 병합혐기성소화를 위해 폐기물의 혐기성소화 가능성 및 열화학적 전처리 방법에 대해 평가하였다. 폐기물의 혐기성소화 가능성 평가 결과, 음식물류폐기물이 탈수슬러지에 비해 혐기성미생물에 의해 분해 가능한 유기물 농도 및 methane yield가 각각 2.2배, 1.3배 더 높게 평가되었다. 바이오가스 발생량의 증대를 위해서는, 음식물류폐기물의 혼합비율을 증가시키는 것이 필요할 것으로 판단되었으며, 열화학적 전처리 효율은 반응온도, NaOH 주입량, 반응시간, 혼합비율 조건에 대해 평가하였다. 전처리 효율 및 탈수능을 통해 평가한 결과, 최적 열화학적 가용화 전처리 조건은 반응온도 140℃, NaOH 주입량 60 meq/L, 반응시간 60 min, 혼합비율 1:5로 평가되었다. 최적 열화학적 가용화 전처리 조건 적용 전과 후의 methane yield를 비교한 결과, 전처리를 적용한 경우에서, 가스발생속도 및 methane yield가 각각 1.6, 1.5배 증가하였다. 따라서, 탈수슬러지 및 음식물류폐기물의 효율적인 병합혐기성소화를 위해서는 음식물류폐기물의 혼합비율을 증가시키며, 폐기물의 전처리를 통해 가용화 효율을 증대시키는 것이 필요하다고 판단된다.

• 한국재료학회지
• /
• 제11권8호
• /
• pp.697-702
• /
• 2001

열화학 기상 증착법을 이용하여 암모니아 처리에 따른 촉매 금속의 표면형태와 탄소 나노튜브의 성장을 조사하였다. 암모니아 처리의 열화학 과정의 조절에 의해 고르게 분산된 수직 성장된 탄소 나노튜브를 얻었다. 탄소 나노튜브 합성시 암모니아처리는 수직성장 및 고밀도 성장에 중요한 과정으로 그 역할에 대해 알아보았다. 고밀도의 수직 배향된 탄소나노튜브의 구조와 형태는 주사전자 현미경과 투과전자 현미경, 라만을 이용하여 관찰하였다.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Pre-symposium of the 10th ISWPC Recent Advances in Paper Science and Technology
• /
• pp.375-380
• /
• 1999

In order to improve the optical properties of high yield pulp, bleached chemi-thermo-mechanical pulp (BCTMP) was produced from CTMP of Betula maximowicziana Regel by two staged ozone-hydrogen peroxide bleaching. This pulp was used for the evaluation of the improvement of optical properties, chemical characteristics of lignin in fiber, and the relationship between lignin and optical properties in fiber cell wall. By hydrogen peroxide treatment, the brightness was improved, but the post color number (PC No.) was not. There was little improvement on optical properties by ozone treatment, but his could be solved by using two staged ozone-hydrogen peroxide bleaching. The hydrogen peroxide treatment did not make nay change on chemical characteristics of lignin in cell wall, but by ozone treatment, it was found that the non-aromatic conjugated structure was existed in the surface of cell wall, but this could be removed by hydrogen peroxide treatment in two staged ozone-hydrogen peroxide treatment. Therefore, the optical properties was significantly improved due to the removal of non-aromatic conjugated structure.

• 펄프종이기술
• /
• 제47권3호
• /
• pp.47-54
• /
• 2015

In this study, effects of kneading treatment on the properties of hardwood bleached kraft pulp (HwBKP), softwood bleached kraft pulp (SwBKP) and hardwood bleached chemi-thermo-mechanical pulp (HwBCTMP) were elucidated with a laboratory two-shaft kneader. Kneading treatment was performed at 30% (w/w) of pulp concentration and the number of passes through the kneader was adjusted from 0 to 10 passes. Then, changes in properties of pulp fibers were evaluated. It was found that fiber characteristics were influenced by kneading treatment. Fiber length was decreased with kneading while other morphological properties such as fiber width, curl and kink became increased as the number of passes through the kneader increased from 0 to 5 passes. The magnitude of changes in the morphological properties of softwood chemical pulp was the largest, followed by hardwood chemical pulp. The morphological properties of HwBCTMP were little influenced by kneading treatment. Swelling of fiber measured by WRV was increased with kneading except of HwBCTMP.

• Membrane and Water Treatment
• /
• 제13권5호
• /
• pp.209-217
• /
• 2022

In the present research, Ficus religiosa Bark (FRB) is used as an adsorbent for the removal of heavy metal Cr (VI) ions. This Ficus religiosa Bark was characterized by Scanning Electron Microscope, Fourier transform infrared Spectroscopy, Thermo Gravimetric Analyzer and the results showed that activated adsorbent have high adsorption capacity and withstand even in high temperature. Batch and Continuous experiments were conducted to determine the effect of various parameters such as pH, contact time, adsorbent dose and initial metal concentration. The biosorption followed pseudo first order kinetic model. The adsorption isotherms of Cr (VI) on Ficus religiosa fitted well with the Temkin model. In Batch study, maximum biosorption capacity of Cr (VI) was found to be 37.97 mg g^-1 (at optimal pH of 2, adsorbent dosage of 0.3 grams and concentration of Cr (VI) is100 mg L^-1). The Continuous mode of study shows that 97% of Cr (VI) ion removal at a flow rate of 15 ml min^-1. From the results, selected Ficus religiosa Bark has the higher adsorption capacity for the removal of Cr (VI) ions from wastewater.

• 상하수도학회지
• /
• 제29권1호
• /
• pp.57-63
• /
• 2015

Recently, Korea's municipal wastewater treatment plants generated amount of wastewater sludge per day. However, ocean dumping of sewage sludge has been prohibited since 2012 by the London dumping convention and protocol and thus removal or treatment of wastewater sludge from field sites is an important issue on the ground site. The hydrothermal carbonization is one of attractive thermo-chemical method to upgrade sewage sludge to produce solid fuel with benefit method from the use of no chemical catalytic. Hydrothermal carbonization improved that the upgrading fuel properties and increased materials and energy recovery, which is conducted at temperatures ranging from 200 to $350^{\circ}C$ with a reaction time of 30 min. Hydrothermal carbonization increased the heating value though the increase of the carbon and fixed carbon content of solid fuel due to dehydration and decarboxylation reaction. Therefore, after the hydrothermal carbonization, the H/C and O/C ratios decreased because of the chemical conversion. Energy retention efficiency suggest that the optimum temperature of hydrothermal carbonization to produce more energy-rich solid fuel is approximately $200^{\circ}C$.