• Journal of the Korean Ceramic Society
• /
• v.50 no.6
• /
• pp.470-475
• /
• 2013

In this study, we report that effects of a filler with a high coefficient of thermal expansion on a sealant for high-temperature ($750{\sim}850^{\circ}C$) SOFC. We designed a $SiO_2-BaO-ZnO-B_2O_3-Al_2O_3$ glass system with a softening temperature higher than $750^{\circ}C$. The properties of the glass system show not only low volumetric shrinking but also low swelling. The glass system did not create a crystal phase during along-term heat treatment. We fabricated a seal gasket with 0, 10, 15, and 20 wt% cristobalite added as filler materials with glass powder. The coefficient of thermal expansion of the seal gasket increased according to cristobalite content. During along-term heat treatment, the leak rate decreased by about 5% after a heat treatment in an oxidizing atmosphere at $750^{\circ}C$ for 2000 h, also decreasing by about 6% after a heat treatment in a reducing atmosphere at $750^{\circ}C$ for 1000 h.

• Korean Journal of Materials Research
• /
• v.26 no.4
• /
• pp.173-181
• /
• 2016

In order to use coal tar pitch (CTP) as a raw material for carbon fibers, it should have suitable properties such as a narrow range of softening point, suitable viscosity and uniform optical properties. In this study, raw CTP was modified by heat treatment with three types of polymer additives (PS, PET, and PVC) to make a spinnable pitch for carbon fibers. The yield, softening point, C/H ratio, insoluble yield, and meso-phase content of various modified CTPs with polymer additives were analyzed by changing the type of polymer additive and the heat treatment temperature. The purpose of this study was to compare the properties of CTPs modified by polymer addition with those of a commercial CTP. After the pitch spinning, the obtained green fibers were stabilized and carbonized. The properties of the respective fibers were analyzed to compare their uniformity, diameter change, and mechanical properties. Among three polymer additives, PS220 and PET261 pitches were found to be spinnable, but the carbon fibers from PET261 showed mechanical properties comparable with those of a commercial CTP produced by an air-blowing method (OCI284). The CTPs modified with polymer additive had higher ${\beta}$-resin fractions than the CTP with only thermal treatment indicating a beneficial effect of carbon fiber application.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.101.3-101.3
• /
• 2010

Glass frit은 실리콘 태양전지의 Ag/Si contact을 위해 필수적이다. 태양전지의 고효율 특성 구현 때문에, Contact resistance(Rc)가 우수한 Pb-frit의 사용이 불가피한 상황이다. 본 연구는 기존의 Pb계를 무연화함과 동시에 동등수준의 효율을 목표로 하였다. Ag 분말 size 및 glass frit의 열적 거동 특성이 SiNx 코팅층 침투와 Ag re-crystallites에 미치는 영향에 대해 평가하였다. 6 inch 다결정 실리콘 웨이퍼를 사용하였으며, softening temperture(Sp)별로 4종의 Bi계 glass frit을 제조 하였고, 분말 size가 다른 3종의 Ag powder를 선정하였다. Glass frit Sp가 $460^{\circ}C$ 이상의 경우에는 효율이 10% 미만이였으나 Sp $460^{\circ}C$ 이하에서는 16% 수준의 효율을 확인할 수 있었다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.191-194
• /
• 2003

The results from a systematic study of the response of a Ti-6Al-4V alloy under quasi-static and dynamic loading at different strain rates and temperatures are presented. It has been shown that the work-hardening rate decreased as the strain rate and the strain increased. The correlations and predictions using modified KHL (Khan-Huang-Liang) viscoplastic constitutive model are compared with those from JC (Johnson-Cook) model and experimental observations. Overall, KHL model correlations and predictions compared much more favorably than the corresponding JC model predictions and correlations.

• Journal of the Korean Ceramic Society
• /
• v.38 no.7
• /
• pp.628-633
• /
• 2001

전자 패키징에 적용 가능한 저융점 유리 중에서 납성분이 포함되어 있지 않는 Bi계 유리의 연구를 행하였다. 기판과의 일체화를 위한 유리의 응용으로, 소자와의 반응 억제와 열응력 완화를 위해 유리의 저융점화 및 열팽창계수를 제어하였다. 본 연구에서 제조된 Bi계 유리는 DTA와 TMA의 열분석을 통해 5$50^{\circ}C$ 부근에서 연화점이 있고, 열팽창계수는 7.52~12.09$\times$$10^{-6}$/$^{\circ}C$의 범위였으며, 비유전율은 9~13이었다. 본 연구의 납성분을 포함되어 있지 않는 유리조성은 우수한 내산성을 나타내었다.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1184-1189
• /
• 2004

Coking process is the thermal decomposition of bituminous coal with final temperature of about $900^{\circ}C$ Because coke plays important roles in ironmaking process in a blast furnace it's essential for developing modeling of coke oven. In this study, An unsteady 2-dimesional model is proposed to simulate coking process in a coke oven. In this model, gas and solid phase are assumed homogeneous continnum and solid bed is assumed as porous media . The model contains governing equations for the solid phase and the gas phase. Complicated phenomena such as swelling, softening, resolidification and shrinkage are neglected and mass loss by drying and devolatilization is reflected by generation of internal pores. Drying, devolatilization, heat transfer and generation of internal pores are also reflected in source terms. Calulated results are compared with experimental data

• Journal of the Korean Society for Precision Engineering
• /
• v.32 no.12
• /
• pp.1023-1029
• /
• 2015

Laser-assisted machining (LAM) is one of the most effective methods for enhancing the machinability of difficult-to-cut materials, such as titanium alloys and various ceramics, and has been studied by many researchers. LAM is a method that facilitates machining by softening a workpiece using a laser heat source. The advantages of the LAM process are decreases in tool wear, cutting force, and surface roughness. However, when the material is over-heated, melting or burning can occur. This study analyzed the heat source distribution with regard to overlapping of preheating on the laser heating path with an acute angle, a right angle and obtuse angles. Then, a power reduction method was proposed to reduce the melting and burning of the workpiece.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.359-361
• /
• 2008

Glasses in the $SnO_2-(50-x)P_2O_5-xB_2O_3$ system were examined as potential replacement for the PbO glass frits with low firing temperature for component materials of a plasma display panel. The glasses were evaluated for their structural and the thermal expansion coefficient, glass transition and glass softening temperatures and Vickers hardness as a function of the $B_2O_3$ content.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.4
• /
• pp.653-658
• /
• 1998

In order to provide orange sac for off-season processing of sac-suspended orange juice, orange was treatee into intermediate production of orange sac and segment, stored at 2$0^{\circ}C$ during 3 months for assessment of sac-quality providing various processing conditions. Lowering the pH of syrup and sterilization temperature reduced the deterioration of sac quality in terms of intensity and destruction of sac. Sugar content of syrup had little relation with intensity of orange sac at pH 6.5, whereas in the range of pH 3.0~3.8, the increase of sugar content increased intensity of sac. The storage of segment form maintained better quality than that of sac form. The absorbance of syrup was linearly inverse to sac intensity. The deterioration of sac quality may be related to effulence of some materails in sac. Sac product sterilized at below $65^{\circ}C$ had possibility to be contaminated by microbes.

• Computers and Concrete
• /
• v.17 no.6
• /
• pp.703-721
• /
• 2016

A novel approach to modeling concrete behavior at the stage of its maturing is presented in this paper. This approach assumes that at any point in the structure, concrete is composed of a set of layers that are activated in time layer by layer, based on amount of released heat that is produced during process of the concrete's maturing. This allows one to assume that each newly created layer has nominal stiffness moduli and tensile/compressive strengths. Hence introduction of explicit stiffness moduli and tensile/compressive strength dependencies on time, or equivalent time state parameter, is not needed. Analysis of plain concrete (PC) and reinforced concrete (RC) structures, especially massive ones, subjected to any kind of straining in their early stage of existence, mostly due to external loads but especially by thermal loading and shrinkage, is the goal of the approach. In this article a simple elasto-plastic softening model with creep is used for each layer and a general layered model behavior is illustrated on one-dimensional (1D) examples.