• Current Research on Agriculture and Life Sciences
• /
• v.33 no.1
• /
• pp.1-5
• /
• 2015

This study investigated the chelation of a sorghum bran extract using iron (Fe) as a new natural colorant. The composition of the sorghum bran extract and chelation conditions were both examined. The thermal properties of the chelated colorants were analyzed using differential scanning calorimetry (DSC) and a thermal analyzer system(TGA). The sorghum bran extract solution showed a maximum absorbance at 281 nm based on UV/Vis spectrophotometry. According to the chelation pH conditions, pH 7.5 was the most effective. The chelation of the sorghum bran extract increased rapidly when increasing the iron concentration up to 2 mg/L, with no further chelation at a higher concentration. The particle size distribution curve for the chelated tannin revealed four groups: $4.5{\sim}17{\mu}m$, $20{\sim}42{\mu}m$, $45{\sim}80{\mu}m$, and $83{\sim}160{\mu}m$. In a DSC analysis, endothermic peaks attributed to the pyrolysis of the extract and chelated tannin were found at $318^{\circ}C$ and $415^{\circ}C$, respectively. In a TGA analysis, the chelation was shown to increase the final degradation temperature from $253^{\circ}C$ to $382^{\circ}C$, confirming that the chelation improved the thermal stability.

• Journal of the Korean Chemical Society
• /
• v.22 no.3
• /
• pp.158-163
• /
• 1978

The four 1,1-disubstituted 2-vinylcyclopropanes, 1,1-diphenyl-2-vinylcyclopropane (1a), 1,1-dicyano-2-vinylcyclopropane(1b), ethyl 1-cyano-2-vinylcyclopropanecarboxylate(1c), and diethyl 2-vinylcyclopropane-1,1-dicarboxylate(1d) rearranged below $300{\circ}C$ to the corresponding 4,4-disubstituted cyclopentenes, 4,4-diphenylcyclopentene(2a), 3-cyclopentene-1,1-dicarboxylate(2d). Diphenpyl derivative 1a rearranged almost quantitatively to 4,4-diphenylcyclopentene(2a) at the temperature of $250{\circ}C$. Although dicyano derivative 1b in solution underwent the thermal rearrangement at rather low temperature of $170{\circ}C$, the other vinylcyclopropanes, 1c and 1d, in solution rearranged thermally above $220{\circ}C$. In the thermal reaction of 1b, 1c, and 1d considerable amounts of polymers 3 were also produced. Also detected product was the ring-opened diene, ethyl 2-cyano-2,4-hexadienoate(4), in case of the pyrolysis of 1c. The observed facile rearrangement of disubstituted vinylcyclopropanes was explained by the radical stabilization effect of substituents on the diradical intermediates 5.

• Clean Technology
• /
• v.16 no.3
• /
• pp.198-205
• /
• 2010

Two sets of thermal reaction experiment for chlorinated hydrocarbons were performed using an isothermal tubular-flow reactor in order to investigate thermal decomposition, including product distribution of chlorinated hydrocarbons. The effects of $H_2$ or Ar as the reaction atmosphere on the thermal decomposition and product distribution for dichloromethane($CH_2Cl_2$) was examined. The experimental results showed that higher conversion of $CH_2Cl_2$ was obtained under $H_2$ atmosphere than under Ar atmosphere. This phenomenon indicates that reactive-gas $H_2$ reaction atmosphere was found to accelerate $CH_2Cl_2$ decomposition. The $H_2$ plays a key role in acceleration of $CH_2Cl_2$ decomposition and formation of dechlorinated light hydrocarbons, while reducing PAH and soot formation through hydrodechlorination process. It was also observed that $CH_3Cl,\;CH_4,\;C_2H_6,\;C_2H_4$ and HCl in $CH_2Cl_2/H_2$ reaction system were the major products with some minor products including chloroethylenes. The $CH_2Cl_2$/Ar reaction system gives poor carbon material balance above reaction temperature of $750^{\circ}C$. Chloroethylenes and soot were found to be the major products and small amounts of $CH_3Cl$ and $C_2H_2$ were formed above $750^{\circ}C$ in $CH_2Cl_2$/Ar. The thermal decomposition reactions of chloroform($CHCl_3$) with argon reaction atmosphere in the absence or the presence of $CH_4$ were carried out using the same tubular flow reactor. The slower $CH_3Cl$ decay occurred when $CH_4$ was added to $CH_3Cl$/Ar reaction system. This is because :$CCl_2$ diradicals that had been produced from $CHCl_3$ unimolecular dissociation reacted with $CH_4$. It appears that the added $CH_4$ worked as the :$CCl_2$ scavenger in the $CHCl_3$ decomposition process. The product distributions for $CHCl_3$ pyrolysis under argon bath gas were distinctly different for the two cases: one with $CH_4$ and the other without $CH_4$. The important pyrolytic reaction pathways to describe the important features of reagent decay and intermediate product distributions, based upon thermochemistry and kinetic principles, were proposed in this study.

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1504-1507
• /
• 1999

We have grown vertically aligned carbon nanotubes in a large area of Co-Ni codeposited Si substrates by the thermal CVD using $C_2H_2$ gas. Since the discovery of carbon nanotubes, Synthesis of carbon nanotubes for mass production has been achieved by several methods such as laser vaporization arc discharge, and pyrolysis. In particular, growth of vertically aligned nanotubes is of technological importance for applications to FED. Recently, vertically aligned carbon nanotubes have been grown on glass by PECVD Aligned carbon nanotubes can be also grown on mesoporous silica and Fe patterned porous silicon using CVD. Despite such breakthroughs in the growth, the growth mechanism of the alignment are still far from being clearly understood. Furthermore, FED has not been clearly demonstrated yet at a practical level. Here, we demonstrate that carbon nanotubes can be vertically aligned on catalyzed Si substrate when the domain density reaches a certain value. We suggest that steric hindrance between nanotubes at an initial stage of the growth forces nanotubes to align vertically and then nanotubes are further grown by the cap growth mechanism.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.10a
• /
• pp.35.1-35.1
• /
• 2011

New photovoltaic (PV) materials and manufacturing approaches are needed for meeting the demand for lower-cost solar cells. The prototypal thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4~1.6 ev and a large absorption coefficient of ${\sim}10^4\;cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative method for large area deposition of CZTS thin films that is potentially high throughput and inexpensive when used to produce monolithically integrated solar panel modules. Specifically, we have developed an aqueous chemical approach based on chemical bath deposition (CBD) with a subsequent sulfurization heat treatment. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and good optical properties. A preliminary solar cell device was fabricated to demonstrate rectifying and photovoltaic behavior.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.60 no.3
• /
• pp.114-119
• /
• 2011

Large Power transformer is a complex and critical component of power plant and consists of cellulosic paper, insulation oil, core, coil etc. Insulation materials of transformer and related equipment break down to liberate dissolved gas due to corona, partial discharge, pyrolysis or thermal decomposition. The dissolved gas kinds can be related to the type of electrical faults, and the rate of gas generation can indicate the severity of the fault. The identities of gases being generated are using very useful to decide the condition of transformation status. Therefore dissolved gas analysis is one of the best condition monitoring methods for power transformer. Also, on-line multi-gas analyzer has been developed and installed to monitor the condition of critical transformers. Rogers method, IEC method, key gas method and Duval Triangle method are used to failure diagnosis typically, and those methods are using the ratio or kinds of dissolved gas to evaluate the condition of transformer. This paper analyzes the reliability of transformer diagnostic methods considering actual dissolved gas concentration. Fault diagnosis is performed based on the dissolved gas of five transformers which experienced various fault respectively in the field, and the diagnosis result is compared with the actual off-line fault analysis. In this comparison result, Diagnostic methods using dissolved gas ratio like Rogers method, IEC method are sometimes fall outside the ratio code and no diagnosis but Duval triangle method and Key gas method is correct comparatively.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.10
• /
• pp.901-909
• /
• 2013

Owing to the Increasing use of fossil fuels, worldwide concerns over environmental pollution are increasing. As a solution, ligneous biomass has emerged as a promising alternative fuel in recent times. Therefore, in this study, a moisture evaporation model that largely influences the energy density and efficiency of ligneous biomass is studied using a numerical approach. Furthermore, the thermal characteristics are analyzed in terms of torrefaction temperature and moisture fractions in the wood, and the type of wood species. The results show that the temperature and moisture fractions of wood decrease with an increase in the torrefaction temperature. In particular, when the torrefaction temperature is lower than 423K, there were little changes in the moisture fraction in the wood. Furthermore, it was found that charcoal is produced more slowly as the moisture fraction in the wood increases.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.1
• /
• pp.17-22
• /
• 2010

The aim of this study is to research applicable possibility of DSI (Dry Sorbent Injection) technique in $SO_2$ removal process using lab-scale facility based on 500MW in capacity coal-fired thermal power plant operated by South Korea N. Power Co., Ltd. To increase the $SO_2$ removal efficiency, it is considered the mixing enhancement as different shapes called lobed-plate and stepplate tested ultimately for optimum shape. Also it tested to analysis $SO_2$ removal efficiency by numbers of injection holes. At experimental it showed the $SO_2$ removal efficiency is higher using mixing enhancement than not installed mixing enhancement and case on the step-plate was shown the most $SO_2$ removal efficiency. Also, $SO_2$ removal efficiency was higher recording which will increase the injection holes case on not installed mixing enhancement. But, the $SO_2$ removal efficiency was higher 4 injection holes case on installed mixing enhancement.

• Journal of the Korean Society for Railway
• /
• v.12 no.6
• /
• pp.1059-1066
• /
• 2009

Recently, the amount of thermosetting plastic wastes has increased with the production of reinforced plastic composites and causes serious environmental problems. The epoxy resins, one of the versatile thermosetting plastics with excellent properties, cannot be melted down and remolded as what is done in the thermoplastic industry. In this research, a series of experiments that decompose epoxy resin and recover carbon fibers from carbon fiber reinforced epoxy composites applied to railway vehicles was performed. We experimentally examined various decomposition processes and compared their decomposition efficiencies and mechanical property of recovered carbon fibers. For the prevention of tangle of recovered carbon fibers, each composites specimen was fixed with a Teflon supporter and no mechanical mixing was applied. Decomposition products were analyzed by scanning electron microscope (SEM), gas chromatography mass spectrometer (GC-MS), and universal testing machine (UTM). Carbon fibers could be completely recovered from decomposition process using nitric acid aqueous solution, liquid-phase thermal cracking and pyrolysis. The tensile strength losses of the recovered carbon fibers were less than 4%.

• Elastomers and Composites
• /
• v.35 no.4
• /
• pp.272-280
• /
• 2000

The experimental kinetics was analyzed for commercial rubbers such as NR, IR, BR, SBR 1500, and SBR 1700. Kinetic analysis for the commercial rubbers was performed using a thermogravimetric method, which the activation energies of NR obtained by Kissinger, Friedman, ana Ozawa's method were 195.0, 198.3, and 186.3 kJ/mol, respectively. whereas that of SBR 1500 were 246.4, 247.5, and 254.8 kJ/mol, respectively. It was shown that the yield of pyrolytic oil was generally increased with increasing the final temperature. Considering the effect of heating rate. it was found that the yield of pyrolytic oil was not consistent for each sample. The number average molecular weight of pyrolitic oil of SBR 1500 was in the range of 740-2486. The calorific value of SBR 1500 was 39-40 kJ/g, and it might be a considerable energy potential although it was lower than the conventional fuel such as kerosene, diesel, light fuel, and heavy fuel.