• Geomechanics and Engineering
• /
• v.16 no.5
• /
• pp.503-512
• /
• 2018

Globally there is an increasing need to reduce the greenhouse gas emissions and increase the use of renewable sources of energy. The storage of solar thermal energy is a crucial aspect for implementing the solar energy for space heating in high latitudes, where solar insolation is high in summer and almost negligible in winter when the domestic heating demand is high. To use the solar heating during winter thermal energy storage is required. In this paper, equations representing the single U-tube heat exchanger are implemented in weak form edge elements in COMSOL Multiphysics(R) to speed up the calculation process for modelling of a borehole storage layout. Multiple borehole seasonal solar thermal energy storage scenarios are successfully simulated. After 5 years of operation, the most efficient simulated borehole pattern containing 168 borehole heat exchangers recovers 69% of the stored seasonal thermal energy and provides 971 MWh of thermal energy for heating in winter.

• Earthquakes and Structures
• /
• v.26 no.4
• /
• pp.251-259
• /
• 2024

In this paper, the thermal post-buckling behavior of graphene platelets reinforced metal foams (GPLRMFs) plate with initial geometric imperfections on nonlinear elastic foundations are studied. First, the governing equation is derived based on the first-order shear deformation theory (FSDT) of plate. To obtain a single equation that only contains deflection, the Galerkin principle is employed to solve the governing equation. Subsequently, a comparative analysis was conducted with existing literature, thereby verifying the correctness and reliability of this paper. Finally, considering three GPLs distribution types (GPL-A, GPL-B, and GPL-C) of plates, the effects of initial geometric imperfections, foam distribution types, foam coefficients, GPLs weight fraction, temperature changes, and elastic foundation stiffness on the thermal post-buckling characteristics of the plates were investigated. The results show that the GPL-A distribution pattern exhibits the best buckling resistance. And with the foam coefficient (GPLs weight fraction, elastic foundation stiffness) increases, the deflection change of the plate under thermal load becomes smaller. On the contrary, when the initial geometric imperfection (temperature change) increases, the thermal buckling deflection increases. According to the current research situation, the results of this article can play an important role in the thermal stability analysis of GPLRMFs plates.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.3
• /
• pp.1-10
• /
• 1998

In this paper, we investigated the improvement of characteristics of knock, emission and fuel consumption rate by optimizing the location and size of water transfer holes in cylinder head gasket without change of engine water jacket design itself. The cooling system was modified in the direction of reducing the metal temperature in the head and increasing the metal temperature in the block. The optimization of water transfer holes in cylinder head gasket was obtained by "flow visualization test". The water transfer holes were concentrated in front side of the engine in order to reduce thermal boundary layer in the water jacket of No. 2 and No. 3 combustion changer in the cylinder head, which would have a large knock intensity, and increase thermal boundary layer in the water jacket of the cylinder block. When the modified coolant flow pattern was applied as proposed in this paper, the knock characteristic was improved. The spark timing was advanced up to 2$^{\circ}$ in low and middle speed range at a full load. In addition, HC emission at MBT was reduced by 5.2%, and the fuel consumption rate was decreased up to 1% in the driving condition of 2400 rpm and 250 KPa. However, since this coolant flow pattern mentioned in this paper might deteriorate the performance of vehicle cooling system due to the coolant flow rate reduction, a properly optimized point should be obtained. obtained.

• Tribology and Lubricants
• /
• v.26 no.6
• /
• pp.311-316
• /
• 2010

Surface texturing of micro dimple or pore-shaped pattern was prepared using a fiber laser system. Surface texturing was designed to have a square pattern with a particular pitch distance for each corresponding density of 5, 10, 20, and 30%. Thermal damages such as bulges and burrs formed during laser irradiation were observed around the dimples. Thermal damages were later removed by lapping using alumina particles of $0.3{\mu}m$ in diameter. Oscillating friction tests were performed against heat-treated high speed steels under lubricated condition. The lubricant used was SAE 5W-30 automotive engine oil. Normal contact pressure and oscillating frequency was 0.28 MPa and 20 Hz, respectively. The tests were continued for 20 minutes, and friction plots were recorded for examination. Results revealed that the coefficient of friction was lowered regardless of texturing density. Moreover, the lowest coefficient of friction was obtained for 10% density texturing. It is attributed to increased lubricity due to the introduction of surface texturing. In addition, it is concluded that the optimum texturing density and pattern must be found for the best lubricity and low friction.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.3 s.258
• /
• pp.225-233
• /
• 2007

The growth of GaN on the patterned substances has proven favorable to achieve thick, crack-free GaN layers. In this paper, numerical modeling of transport and reaction of species is performed to estimate the growth rate of GaN from tile reaction of TMG(trimethly-gallium) and ammonia. GaN growth rate was estimated through the model analysis including the effect of species velocity, thermal convection and chemical reaction, and thermal condition for the uniform deposition was to be presented. The effect of shape and construction of microscopic pattern was also investigated using a simulator to perform surface analysis, and a review was done on the quantitative thickness and shape in making GaN layer on the pattern. Quantitative analysis was especially performed about the shape of reactor geometry, periodicity of pattern and flow conditions which decisively affect the quality of crystal growth. It was found that the conformal deposition could be obtained with the inclination of trench ${\Theta}>125^{\circ}$. The aspect ratio was sensitive to the void formation inside trench and the void located deep in trench with increased aspect ratio.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.30 no.2
• /
• pp.1-12
• /
• 2012

In this experiment, we have manufactured thermal-curable silver pastes for direct printing. And to enhance conductivity, printability, adhesion and hardness during polymer direct-gravure prints, we have manufactured Ag pastes by adding variety of filter contents. Then we have investigated characteristics of rheology in paste according to the gravure printability and the properties of printed conductive patterns. Depending on a variety of Ag powder, there was a big difference in sharpness of printed pattern. And also by the use of carbon, there was a big difference in amount of solvent used, conductivity and in hardness. We could improve doctoring and the sharpness of a pattern by adding Ag paste in carbon particle, but as we have used nano-sized particle, there was an increase in the amount of solvent used and also we have found out that it gives a bad effect as adhesive and hardness becomes weaker. Even though Ag particle has the same spherical shape, the surface treatments could differ from one another. And by the appropriate choice and with the suitable combination of Ag powder, excellent printability and conductivity could be obtained.

• Macromolecular Research
• /
• v.17 no.3
• /
• pp.181-186
• /
• 2009

We fabricated ordered micro/nano patterns induced by controlled dewetting on the topographically patterned PS/P4VP bilayer thin film. The method is based on utilizing microimprinting lithography to induce a topographically heterogeneous bilayer film that allows the controlled dewetting upon subsequent thermal annealing. The dewetting that was initiated strictly at the boundary of the thicker and thinner regions was guided by the presence of the topographic structure. The dewetting front velocity of the microdomains in the confined regions was linearly proportional to the measurement time, which enabled us to control the size of the dewet domain with annealing time. In particular, the submicron sized dot arrays between lines were generated with ease when the dewetting was confined into geometry with a few microns in size. The kinetically driven, non-lithographical pattern structures accompanied the pattern reduction to 400%. The pattern arrays on a transparent glass substrate were especially useful for non-circular microlens arrays where the focal length of the lens was easily tunable by controlling the thermal annealing.

• Wind and Structures
• /
• v.28 no.1
• /
• pp.1-17
• /
• 2019

Internal ring beams are primary components of new ring-stiffened cooling towers. In this study, numerical simulation of the internal flow field of a cooling tower with three ring beams under wind-thermal coupling effect is performed. The studied cooling tower is a 220-m super-large hyperbolic indirect natural draft cooling tower that is under construction in China and will be the World's highest cooling tower, the influence of peripheral radiators in operating cooling tower is also considered. Based on the simulation, the three-dimensional effect and distribution pattern of the wind loads on inner surface of the cooling tower is summarized, the average wind pressure distributions on the inner surface before and after the addition of the ring beams are analyzed, and the influence pattern of ring beams on the internal pressure coefficient value is derived. The action mechanisms behind the air flows inside the tower are compared. In addition, the effects of internal ring beams on temperature field characteristics, turbulence kinetic energy distribution, and wind resistance are analyzed. Finally, the internal pressure coefficients are suggested for ring-stiffened cooling towers under wind-thermal coupling effect. The study shows that the influence of internal stiffening ring beams on the internal pressure and flow of cooling towers should not be ignored, and the wind-thermal coupling effect should also be considered in the numerical simulation of cooling tower flow fields. The primary conclusions presented in this paper offer references for determining the internal suction of such ring-stiffened cooling towers.

• Proceedings of the KWS Conference
• /
• 2001.10a
• /
• pp.162-164
• /
• 2001

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.256-259
• /
• 2005

Analysis of behavior pattern and thermal response during bathing and showering provides important fundamental data when developing an automatic bathing/showering system. The behavior pattern and physiological changes during bathing/showering were measured und analyzed for the aged male group. We recorded the volunteers showering at front, back, left and right view using four CCTV cameras in order to study the behavior pattern during showering. The photographic data were analyzed by counting the frequencies of body contact and identifying zones where hands could reach. In order to study the thermal response, we measured the blood pressure (B.P), heart rate (H.R), body temperature (B.T.), breathing rate (B.R) for the different water temperatures and the locations of immersion for the young and old age groups. The results showed that the frequencies of body contacts were varied for different body sections. Also there were some body sections where hands could not be reached because of reduced pliability and muscular strength of the aged group. But we observed rather uniform body contact frequencies when a towel was used. In partial immersion bath experiments, we observed the changes of B.P. H.R and B.T in the case of young and old age groups, and the changes were more significant in the young age group.