• 한국재료학회지
• /
• 제29권7호
• /
• pp.443-450
• /
• 2019

Thermal management is a critical issue for the development of high-performance electronic devices. In this paper, thermal conductivity values of mild steel and stainless steel(STS) are measured by light flash analysis(LFA) and dynamic thermal interface material(DynTIM) Tester. The shapes of samples for thermal property measurement are disc type with a diameter of 12.6 mm. For samples with different thickness, the thermal diffusivity and thermal conductivity are measured by LFA. For identical samples, the thermal resistance($R_{th}$) and thermal conductivity are measured using a DynTIM Tester. The thermal conductivity of samples with different thicknesses, measured by LFA, show similar values in a range of 5 %. However, the thermal conductivity of samples measured by DynTIM Tester show widely scattered values according to the application of thermal grease. When we use the thermal grease to remove air gaps, the thermal conductivity of samples measured by DynTIM Tester is larger than that measured by LFA. But, when we did not use thermal grease, the thermal conductivity of samples measured by DynTIM Tester is smaller than that measured by LFA. For the DynTIM Tester results, we also find that the slope of the graph of thermal resistance vs. thickness is affected by the usage of thermal grease. From this, we are able to conclude that the wide scattering of thermal conductivity for samples measured with the DynTIM Tester is caused by the change of slope in the graph of thermal resistance-thickness.

• Tribology and Lubricants
• /
• 제11권3호
• /
• pp.31-39
• /
• 1995

Grease thermal elastohydrodynamic lubrication (TEHL) problems of line contacts are analyzed numerically. The effects of temperature and rheological paraineters on grease TEHL are investigated using the Herschel-Bulkley model as a theological model of greases. The pressure distribution, the shape of grease film, mean film temperature and surface temperature of solid wall in line contacts are obtained. It is found that thermal effects on the minimum film thickness become remarkable at high rolling speeds. The effect of yield stress of Herschel-Bulkley model on minimum film thickness is negligible, while the theological index and viscosity parameter have significant effects on minimum film thickness.

• 한국산학기술학회논문지
• /
• 제20권7호
• /
• pp.8-15
• /
• 2019

본 연구에서는 칼슘 술폰산염 컴플렉스 그리스와 리튬 컴플렉스 그리스를 합성하고, 그리스의 일반 물성, 유변학적 특성 및 윤활성능을 비교하였다. 내열성 시험인 적점 시험에서 칼슘 술폰산염 컴플렉스 그리스의 열 안정성은 섭씨 300도 이상, 리튬 컴플렉스 그리스는 섭씨 245도로 측정되었다. 점도시험에서 칼슘 술폰산염 컴플렉스 그리스는 7.0 파스칼 초, 리튬 컴플렉스 그리스는 4.5 파스칼 초로 측정되었다. 따라서 칼슘 술폰산염 컴플렉스 그리스가 리튬 컴플렉스 그리스보다 내열성 및 점착성면에서 우수함을 확인하였다. 4-ball 내마모시험에서 칼슘 술폰산염 컴플럭스 그리스는 0.43 밀리미터, 리튬 컴플럭스 그리스는 0.85 밀리미터로 측정되었고, 4-ball 내하중성 시험에서 칼슘 술폰산염 컴플렉스 그리스는 620 킬로그램중, 리튬 컴플렉스 그리스는 125 킬로그램중 으로 측정되었다. 따라서, 칼슘 술폰산염 컴플렉스 그리스가 리튬 컴플렉스 그리스보다 내마모성 및 내하중성에서 우수하였다. 위 시험결과로 고온 및 고하중의 윤활에서는 칼슘 술폰산염 컴플렉스 그리스가 리튬 컴플렉스 그리스보다 더 효과적인 것을 알 수 있었다.

• 한국산업융합학회 논문집
• /
• 제22권6호
• /
• pp.767-773
• /
• 2019

The thermal diffusion performance of the electronic device is a factor for evaluating the stability of the electronic device. Therefore, many of research have been conducted to improve the thermal characteristics of thermal interface materials, which are materials for thermal diffusion of electronic products. In this study, nano thermal grease was prepared by blending graphene, silver and copper nano powders into a thermal grease, a type of thermal interface materials, and the heat transfer rate was measured and compared for the purpose of investigating the improved thermal properties. As a result, the thermal properties were good in the order of graphene, silver and copper, which is thought to be due to the different thermal properties of the nano powder itself.

• 에너지공학
• /
• 제8권2호
• /
• pp.272-278
• /
• 1999

본 연구에서는 지름 30mm, 길이 45mm인 brass와 aluminium 원통 실린더의 접촉면이 ⅰ) 진공 상태에 있을 때 , ⅱ) silicone grease를 충전하였을 때 , ⅲ) silicone grease와 aluminium 분말 (#325) 혼합물을 충전하였을 때의 열접촉저항을 측정하였고, 그 결과를 Fouche 의 해석 모델과 비교하였다. 진공상태에서 비접촉면의 열접촉저항은 표면의 가공 상태에 따라 (2~100)$\times$$10^{-5}$($m^2$$^{\circ}C$/W)의 분포를 나타내었고 접촉 표면을 연마하였을 때에는 거친 표면에 비하여 약 30~50%의 열접촉저항저감을 나타내었다. 그러나, silicone grease를 충전했을 때에는 열접촉저항 값이 약 5~10정도 감소하는 경향을 나타내었다. Fouche 모델을 이용한 해석 결과는 silicone grease로 충전한 접촉면에 대해서 각 10~30%범위에서 아주 잘 일치하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.273-274
• /
• 2009

현재 가로등의 93.3[%]를 차지하고 있는 나트륨램프는 색상이 적황색이며, 시력에 장애와 피로감을 주어 인체에 해로우므로 고효율 램프로 교체되고 있으며 백열전구는 전력을 많이 소모하고 잦은 고장으로 빈번한 대체와 유지보수를 필요로 하므로 LED를 선택하면, 유지보수 비용과 안전성, 에너지 효율성면에서 큰 강점을 갖는다. 본 연구에서는 에너지 효율이 높은 LED 가로등 제작을 위한 모듈을 제작하여, 열적, 광학적 분석을 하였다. 동작 150분 후, LED Module의 PCB기판 6 Point에서 Thermal Grease와 Thermal Pad의 처리에 의한 열적 변화를 측정하였으며, Thermal Grease 처리는 Thermal Pad 보다 평균 3 $[^{\circ}C]$ 정도 낮은 35 $[^{\circ}C]$결과를 얻었으며, 제작된 LED Module의 광학적평가의 결과는 10 [m] 높이에서 $20\times20\;[m^2]$ 면적에 조사된 조도의 최대,최소값은 10.9~0.6 [lx]이고, 주로 10~5 [lx] 값이 조도의 면적을 차지하였으며, 곡선은 옆으로 넓게 펼쳐진 곡선을 나타내었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제17권4호
• /
• pp.1-7
• /
• 2015

This paper addresses technical problems of thermal contact conductance or resistance which inevitably occurs in most cryogenic engineering systems. The main focus of this paper is to examine what kind of physical factors primarily influences the thermal contact resistance and to suggest how it can be minimized. It is a good practical rule that the contact surface must have sub-micron roughness level with no oxide layer and be thinly covered by indium, gold, or Apiezon-N grease for securing sufficient direct contact area. The higher contact pressure, the lower the thermal contact resistance. The general description of this technique has been widely perceived and reasonable engineering results have been achieved in most applications. However, the detailed view of employing these techniques and their relative efficacies to reduce thermal contact resistances need to be thoroughly reviewed. We should consider specific thermal contact conditions, examine the engineering requirements, and execute each method with precautions to fulfil their maximum potentials.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.439-444
• /
• 2004

The important problem in high speed spindle is to reduce and minimize the thermal effect by motor and ball bearings. In this study. the effects of bearing preload and cooling for high speed spindle with high frequency motor are investigated. A high speed spindle is composed of angular contact ball bearings, high frequency motor, grease lubrication, oil jacket cooling, and so on. Heat generation of the bearing and the high frequency motor are estimated from the theoretical and experimental data. The thermal analyses of high speed spindle to minimize the thermal effect and maximize the cooling effect are carried out under the various cooling conditions and preload. Method of variable bearing preload and cooling can be useful to design the high speed motor spindle. The results show that the optimal preload and cooling are very effective to minimize the thermal displacement by motor and ball bearing.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.41-46
• /
• 2003

The important problem in high speed spindles is to reduce and minimize the thermal effect by motor and bail bearings. Thermal characteristics according to the bearing pre-load and cooling condition are studied for the test spindl with grease lubrication and high frequency motor. Bearing and motor we main heat generation, and heat generation by ball bearings as a function of load, viscosity and gyroscopic moment effect are considered. Temperature distribution and thermal displacement according to the speed of spindle are measured by thermocouple and gap sensor. The results show that the fitting pre-load and cooling temperature are very effective to minimize the thermal effect by motor an ball bearings.

• 한국태양에너지학회 논문집
• /
• 제35권1호
• /
• pp.21-28
• /
• 2015

A small washer powered directly and solely by thermal radiation was constructed and tested to explore the feasibility of using solar energy or other types of thermal radiation for washing and cleaning. In principle, TA (ThermoAcoustic) washers have the benefits of simpler design and operation and fewer energy conversion processes, thus should be more energy efficient and cost less than electric washing/cleaning systems. The prototype TA converter we constructed could sustain itself with consistent fluid oscillations for more than 20 minutes when powered by either concentrated solar radiation or an IR (infrared) heater. The frequencies of water oscillations in the wash chamber ranged from 2.6 to 3.6 Hz. The overall conversion efficiency was lower than the typical efficiencies of TA engines. Change in water temperature had little effect on the oscillatory flow in the TA washer due to its low efficiency. On the other hand higher water temperatures enhanced grease removal considerably in our tests. Methods for measuring the overall conversion efficiency, frictional loss, and grease removal of the TA washing system we designed were developed and discussed.