• Tribology and Lubricants
• /
• 제13권3호
• /
• pp.85-92
• /
• 1997

An experimental study was performed to discover the tribological behaviors of pure silver coated 52100 bearing steel. Pure silver coatings ranging from 80 nm to several micrometers were produced by a thermal evaporation coating method. Experiments using a thrust ball bearing-typed rolling test-rig were performed for the investigations of the influence of coating thickness on the tribological rolling behavior. The existence of optimum film thickness which revealed minimum rolling resistance was discovered. A careful analysis on the contact surfaces for the optimum film thickness has been performed. The contact patches produced by the transferred silver films played an important role for the rolling resistance to keep low.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.212-220
• /
• 2000

Single flighted screw extrusion is the most cost effective method for the production of film, sheet, pipe and the fundamental step in other processes including blow molding and injection molding. The temperature of polymer melts and injection pressure play a very important role in the injection molding machine. Thermal distortion and displacement of screw by temperature difference and injection pressure difference cause adhesive wear by metal-to-metal contact. In this paper we analyze thermal distortion and stress of screw includes pressure and temperature distributions by finite element analysis to understand dynamic characteristics of screw.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.66-72
• /
• 2009

Al-based composites reinforced with SiC particulate were fabricated using a thermal spray process, and dry sliding wear behavior of the composites was investigated. Pre-mixed Al and SiC powders were sprayed on an A16061 substrate by flame spraying, and dry sliding wear test were performed under various sliding speed and applied load conditions against ${Al_2}{O_3}$ ball. Wear behavior of the composites was studied by using scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). And build-up mechanism of MML on the worn surface of the composites was examined. It was revealed that these MML was formed of debris from the contact surface of the composites and effected to wear behavior of the composites protecting the contact surface of the composites.

• 한국정밀공학회지
• /
• 제27권1호
• /
• pp.91-98
• /
• 2010

The increasing of power and processing speed and miniaturization of central processor unit (CPU) used in electronics equipment requires better performing thermal management systems. A typical thermal management package consists of thermal interfaces, heat dissipaters, and external cooling systems. There have been a number of experimental techniques and procedures for estimating thermal conductivity of thin, compressible thermal interface material (TIM). The TIM performance is affected by many factors and thus TIM should be evaluated under specified application conditions. In compact packaging of electronic equipment the chip is interfaced with a thin heat spreader. As the package is made thinner, the coupling between heat flow through TIM and that in the heat spreader becomes stronger. Thus, a TIM characterization system for considering the heat spreader effect is proposed and demonstrated in detail in this paper. The TIM test apparatus developed based on ASTM D-5470 standard for thermal interface resistance measurement of high performance TIM, including the precise measurement of changes in in-situ materials thickness. Thermal impedances are measured and compared for different directions of heat dissipation. The measurement of the TIM under the practical conditions can thus be used as the thermal criteria for the TIM selection.

• 정보저장시스템학회논문집
• /
• 제11권1호
• /
• pp.11-15
• /
• 2015

In HDD industry, many technologies have been developed and investigated as means to increase the areal density of drives. Thermal flying-height control has been considered and widely applied in current HDD. When contact occur between TFC slider and disk, the slider has a friction heating induced by highly rotated disk. Moreover, because of the friction heating, additional protrusion of slider can occur. The additional protrusion in contact situation can be a severe effect on head part of slider and disk. Therefore, in this paper, we analyze the friction heating and additional protrusion in contact situation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.5-6
• /
• 2009

In this paper, plasma ion implant is performed with $PH_3$ gas diluted by helium gas on P-type Si wafer (100). Spike Rapid Thermal Processing(RTP) annealing performed for 30~60 sec from $800\;^{\circ}C$ to $1000\;^{\circ}C$ in $N_2+O_2$ ambient. Crystalline defect is analyzed by Transmission Electron Microscope(TEM) and Double crystal X-ray Diffraction(DXRD). Contact resistivity($\rho c$), contact resistance(Rc) and sheet resistance(Rs) are analyzed by measuring Transfer Length Method(TLM) using 4155C analysis. As annealing temperature increase, Rs decrease and ${\rho}c$ and Rc increase at temperature higher than $850\;^{\circ}C$. We achieve low Rs, ${\rho}c$ and Rc with Plasma ion implant and spike RTP.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1391-1394
• /
• 2007

In order for Hypoid gear development. Gears are required to sustain heavy loads or on applications where the gear box is made or a material with a different coefficient of thermal expansion form that or the gears and shafts, it is desirable to make a deflection and contact check under load. The deflection test is performed in the actual gear mounting using completely processed gear. This test should cover the full operating range of gear loads from no load to peak load. Under peak load the contact pattern should extend to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 추계학술대회 논문집
• /
• pp.151-154
• /
• 1998

We have investigated a correlation of the electrical properties of the Pd/Ge/Pd/Ti/Au ohmic contact on n-InGaAs with its microstructures for the high temperature application of compound semiconductor devices. The samples were heat-treated by the rapid thermal annealing at various temperatures. In the contact system, moderately good specific contact resistance was obtained even before annealing because of the low metals-InGaAs barrier height, and better ohmic performances were observed by annealing up to 400˚C. But the ohmic performance was degraded after annealing at 450˚C due to the increment of Pd$_2$Ga$\sub$5/ phases.

• Journal of Astronomy and Space Sciences
• /
• 제17권2호
• /
• pp.151-162
• /
• 2000

근접촉쌍성을 분광형에 따라 A형과 F형으로 분류하여 각각의 물리적 특성과 진화를 조사하였다. 그 결과, 근접촉쌍성이 TRO 이론에 따른 진화 경로를 겪는다고 가정하면, F형이 A형에 비하여 더 접촉에 가까운 즉, W UMa형에 근접한 상태에 있을 가능성이 있음을 알 수 있었다. NCBs의 질량-반경 관계, 질량-광도 관계 및 H-R도를 조사하였는데 그 결과 A형이 F형에 비하여 질량교환이 활발할 것으로 생각된다. 근접촉쌍성은 ZAMS와 평행하게 나타나며 접촉쌍성의 진화 위치와 거의 일치하고 있다.

• Coupled systems mechanics
• /
• 제4권3호
• /
• pp.237-249
• /
• 2015

In the gear meshing process, gear temperature field concerns the meshing surface friction, the friction heat depends on the contact pressure, the contact pressure is affected by the elastic deformation of gears and the temperature field caused by the thermal deformation, so the temperature field, stress field and displacement field should be mutual coupling. It is necessary to consider in meshing gear pair in the operation process of thermodynamic coupling contact stress (TCCS) and thermodynamic coupling deformation (TCD), and based on thermodynamic coupling analysis (TCA) of gear teeth deformation.