• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.6-13
• /
• 2017

This study examines the effect of the type and number of orifices in an in-line mixer to improve the mixing performance and pressure loss. Recently, in-line non-power-consuming mixers have been increasingly used to complement mechanical mixers, which have a long dwell time, noise, excessive energy consumption, and high maintenance costs. An in-line mixer with an orifice for efficient mixing in water treatment was examined by numerical analysis using the commercial code FLUENT. The flow characteristics of pressure loss and velocity distribution within the mixer and the mixing efficiency were compared with and without the orifices. The CFD results show that the mixing efficiency was improved, but the pressure loss was increased by the in-line mixer with an orifice. A sensitivity study was also done on the principal parameters.

• Fire Science and Engineering
• /
• v.29 no.1
• /
• pp.73-79
• /
• 2015

There are three kinds of design method of the fire sprinkler systems. Grid type is connected all branch as a trapezoid. Loop type is connected cross-mains like circle. The last one is a tree type most commonly used. Grid type needs computer program to calculate the friction loss and flow rate apart from very simple form. In loop type, manual calculation is possible. Design engineer can draw up and calculate the demands without computer program. Because water supplies two direction in loop type, friction loss is smaller than tree type. Water distribution in operation area is uniform because of the small differences of sprinklers discharge pressure. Loop type is superior to tree type in respect of total pressure and flow rate. Using the small diameter pipe, the labor and construction cost will be decreased in the end. Loop type sprinkler design is rarely laid out because design engineers don't know the method. This paper is intended to inform that the loop type is better than the tree type in performance and economic point of view. And also this paper intend to use the loop type easily and widely.

• Journal of Korean Society of Water and Wastewater
• /
• v.33 no.1
• /
• pp.43-53
• /
• 2019

In the Geumho River, 4-nitrophenol has been detected, thus it is necessary to investigate the contamination sources in order to prevent the release of this compound. However, the research to estimate the potential source is regarded as complicated research. In this study, the distributions of 4-nitrophenol were simulated and the contribution of the potential sources was estimated using a numerical model(HydroGeoSphere; HGS) and the measuring data of 4-nitrophenol from 2013 to 2017. The altitude data, the land cover data, the flow rates of the tributaries and wastewater treatment plants, and the decay rate of 4-nitrophenol was used as the input data. The results of this research showed that the contribution rates of potential contamination sources in the upstream area were higher than that of the downstream area. Most of the upstream area is the agricultural area, it seemed that 4-nitrophenol was originated from the pesticides. In order to achieve more specific location of sources, an intensive investigation in the upstream is required.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.296-296
• /
• 2015

The aim of this paper is to numerically explore the feasibility of designing a Mini-Hydro turbine. The interest for this kind of horizontal axis turbine relies on its versatility. For instance, in the field of renewable energy, this kind of turbine may be considered for different applications, such as: tidal power, run-of-the-river hydroelectricity, wave energy conversion. It is fundamental to improve the turbine performance and to decrease the equipment costs for achievement of "environmental friendly" solutions and maximization of the "cost-advantage". In the present work, the commercial CFD code ANSYS is used to perform 3D simulations, solving the incompressible Unsteady Reynolds-Averaged Navier-Stokes (U-RANS) equations discretized by means of a finite volume approach. The implicit segregated version of the solver is employed. The pressure-velocity coupling is achieved by means of the SIMPLE algorithm. The convective terms are discretized using a second order accurate upwind scheme, and pressure and viscous terms are discretized by a second-order-accurate centered scheme. A second order implicit time formulation is also used. Turbulence closure is provided by the realizable k - turbulence model. In this study, a mini hydro turbine (3kW) has been considered for utilization of horizontal axis impeller. The turbine performance and flow behavior have been evaluated by means of numerical simulations. Moreover, the performance of the impeller varied in the pressure distribution, torque, rotational speed and power generated by the different number of blades and angles. The model has been validated, comparing numerical results with available experimental data.

• Journal of Korea Water Resources Association
• /
• v.38 no.3 s.152
• /
• pp.223-233
• /
• 2005

In this study, a two-dimensional model for identifying areas of erosion and deposition over a basin was developed based on the mass balance principle in a distributed model. The program consists of three steps: (a) estimation of soil erosion; (b) determination of flow amount and direction; and (c) estimation of mass balance. Soil erosion was estimated with USLE. A single-direction (SF) and a multi-direction flow algorithm (MF) were applied to estimate slope length (L). The Maximum Downhill Slope Method (MDS) and the Neighborhood Method (NBH) were used to estimate the slope degree (S). Sediment transport resulting from eroded soil was estimated using Ferro's (1998) and Swift's (2000) sediment delivery ratio (DR). The model was validated by comparing the predicted sediment yields for three basins with measured data. The developed algorithm showed that Ferro's DR method combined with the MDS and MF produced the best agreement with the dredging records of three agricultural reservoir basins in Korea.

• Journal of Korean Society of Water and Wastewater
• /
• v.33 no.5
• /
• pp.389-394
• /
• 2019

In order to determine the location of average concentration and distribution status of dissolved oxygen in the rectangular aeration tank of the sewage treatment plant was analyzed and the difference of dissolved oxygen concentration was remarkable at each location. Compared with the computational fluid dynamics analysis, it was found that the results were consistent with the measurement results by showing the difference of dissolved oxygen concentration between the locations. Based on the measured data, the representative location of dissolved oxygen in aeration tank was selected by using statistical analysis method and the representative location was expressed in three-dimensional coordinates(LWH : 25%, 50%, 33%) from flow direction and left wall. Also the difference between the dissolved oxygen concentration at the actual measurement location and the average concentration value of the entire aeration tank was founded, and the equations for calibrating the automatic measurement data considering the actual measurement location were calculated.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.65-78
• /
• 1996

The Chungpyung Dam is a 16 yearn old rock-fill dam for a Pumped storage hydro-Power plant, located in the middle of the Korean Peninsula. Since the dam is subjected to the daily water level fluctuation, such as rapid drawdown and refill, thus inducing a structural impact on the behavior of dam body, it draws attention of many engineering concerns. Traditionally, steady-state analysis was employed to investigate the seepage in the dam body, but in this study the seepage analysis was numerically performed by 2-D FEM thansient analysis. As a boundary condition for an analysis, the water level fluctuation was incorporated to simulate the daily change. As a res41t, the various seepage phenomena such as hydraulic gradient, seepage vector, and pore water pressure distribution were quantified at the corresponding time of interest as the water level rises and recedes. The seepage flux was also estimated and compared with the measured data which were both acceptable considering design criteria. The result proves that there is no sign of hazardous sources contributing to the possibility of piping, internal erosion and excess leakage through the dam body.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.1
• /
• pp.37-41
• /
• 1997

Hot-water soluble extracts were prepared from medium-sized barks of Siberian larch (Larix gmelineii). The extracts were fractionated by ultrafiltration method for producing uniform quality of adhesives. Molecular weight distribution of the extracts was ranged of 100 to 300.000. pH of the extracts affected amounts of flux, and the range of pH 6~pH 8 was proper for wood adhesives, because of easy concentration and fast gelation time. Removal of particles greater than $0.45{\mu}m$ from the extracts increased both filtration speed (flux) and yields of solids in the filtrates. In ultrafiltration process. operating pressure, filtrate temperature, and flow rate significantly increased with the increase of individual condition. Ultrafiltration using PM10 membrane was very effective to fractionate and concentrate the extracts. Removal of large particles greater than 0.45 m from the extracts increased filtration speed(flux) and yields of solids in the filtrates. A gelation time was accelerated with the increasing pH of the extracts and its concentration. The Stiasny precipitate(26%) from the filtrate obtained by PM 10 membrane was very lower than that(78%) of the retentates. This ultrafiltration method was efficient for obtaining high yield purified phenolic compounds.

• Journal of Korean Society of Water and Wastewater
• /
• v.31 no.1
• /
• pp.29-37
• /
• 2017

To estimate pollution sources in the watershed with various industries, the simulation of contamination route and distribution of 2-methyl-4,6-dinitriophenol(DNOC) were performed with a numerical model Hydro Geo Sphere. This study was performed calculations of the load using the measured concentration and simulated flow rate. And, the river was divided by the sampling sites at the mainstream, and the contribution rate at downstream sampling sites was calculated for each section. The results showed the concentration of the downstream sampling sites were decided by the concentration of upstream sites, and the contribution rates of the tributaries were calculated below 10%. The results also showed that the impact of the potential sources in Section 1(Geumho1 ~ Geumho2) and Section 5(Geumho5 ~ Geumho6) was larger than in the other area. In Section1 and Section5, It seemed to require detailed investigation.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.2 s.140
• /
• pp.80-87
• /
• 2005

A set of experiments was carried out for obtaining the velocity field around the hydrofoil of finite span, using a wing of the NACA 0012 section in a circulating water channel. DPIV technique was used to measure the velocity field, and the velocity measurements along the span were done for 3 speeds, 3 submerged depths, and 4 angles of attack. Experimental data are compared with the theoretical assumptions, as well as the numerical findings by Lee and Lee(2004). Special care is given to the flow near the tips and in the region close to the leading edge. Though indirect, using the measured data of the velocity, it is now possible to compare the aerodynamic and the hydrodynamic strength of the circulation distribution of a wing in the framework of the lifting-line theory.