• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1852-1854
• /
• 1999

In order to enhance satellite communication system performance, filters are required with the characteristics of sharp skirt, low insertion loss, and high power handling capability. But the performance of microwave passive filters is significantly declined by the conduction losses, especially in case of planar structures using film conductors. By using high temperature superconducting(HTS) film material as the conductor, higher performance could be expected. We have designed and developed narrow bandpass filters using haripin-type superconducting microstrip line for satellite communication. High quality superconducting YBCO thin films have been grown on MgO substrates by pulsed laser deposition(PLD) The deposited YBCO films were patterned by conventional wet-etching process. The transition temperatures of these films had shown 86 - 89 K. The film thicknesses were about 500 nm. Experimental results are presented for the insertion loss and return loss of the filter at 60 K.

• Progress in Superconductivity
• /
• v.4 no.1
• /
• pp.10-13
• /
• 2002

We report the effect of Ca doping in $YBa_2Cu_3O_{7-\delta}$ (YBCO) thin films grown on the Rolling- Assisted, Biaxially Textured Substrates (RABiTS) with the architecture of $CeO_2/YSZ/CeO_2/Ni$. Critical currents of bilayer and trilayer structures of $YBCO/Y_{0.7}Ca_{0.3}Ba_2Cu_3O_{7-\delta}$/(YCaBCO) as well as undoped YBCO for comparison have been measured in a wide range of temperatures and fields. For $6-8^{\circ}$ grain boundaries, 30% Ca-doping in bilayer structure enhances $J_c$ as high as 35%. The enhancement is larger at low temperatures and at magnetic fields. On the other hand, 30% Ca-doping in trilayer structure reduces $J_c$ as high as 60%. Combined with slightly lower $T_c$, this indicates that Ca is overdoped in this structure and degrades GBs.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.1
• /
• pp.116-119
• /
• 2010

In this work, we presented the characterization of 3 dB branch type directional couplers by using High-Tc superconducting thin films. To do this, we deposited YBCO superconducting thin films on MgO substrates by using rf-magnetron sputtering techniques. The designed center frequency was 408 MHz and the designed passband was 20 MHz. Also we designed 3 dB Power difference and $90^{\circ}$ of phase difference between port 3 and port 4. The even and odd mode analysis were used to characterize our directional couplers and em Sonnet (full wave analysis program) was utilized to the optimum design. We reported experimental results, including a center frequency, passband, half power characteristics and phase differences. We confirmed that experimental results were in good agreements with characterization by using full wave analysis program.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.10
• /
• pp.1061-1067
• /
• 2004

In this study, ferroelectric (Ba,Sr)TiO$_3$ and high temperature superconductor YBCO thin films were fabricated by PLD (Pulsed Laser Deposition) method and tuneable bandstop filters were implemented with two different IDC(Interdigital Capacitance) gap patterns, 20${\mu}{\textrm}{m}$ and 30${\mu}{\textrm}{m}$ using these two thin film layers. The resonant frequency was changed by DC bias voltage. By comparing measured results with simulation, the dielectric properties of ferroelectric thin film have been extracted. The permittivity was 820 ～ 900 at 30 K and had an acceptable error range but the loss tangent had a great difference, 0.018 in 30${\mu}{\textrm}{m}$ IDC gap pattern and 0.037 in 20 ${\mu}{\textrm}{m}$.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.235-235
• /
• 2003

The development of a buffer layer is an important issue for the second -generation wire, YBCO coated metal wire. The buffer layer demands not only on the prohibition of the reaction between YBCO and metal substrate, but also the proper lattice match and conductivity for high critical current density (Jc) of YBCO superconductor, In order to satisfy these demands, we suggested CaRuO3 as a useful candidate having that the lattice mismatches with Ni (200) and with YBCO are 8.2% and 8.0%, respectively. The CaRuO3 thin films were deposited on Ni substrates using various methods, such as e-beam evaporation and DC and RF magnetron sputtering. These films were investigated using SEM, XRD, pole-figure and AES. In e-beam evaporation, the deposition temperature of CaRuO3 was the most important since both hi-axial texturing and NiO formation between Ni and CaRuO3 depended on it. Also, the oxygen flow rate had i[n effect on the growth of CaRuO3 on Ni substrates. The optimal conditions of crystal growth and film uniformity were 400$^{\circ}C$, 50 ㎃ and 7 ㎸ when oxygen flow rate was 70∼100sccm In RF magnetron sputtering, CaRuO3 was deposited on Ni substrates with various conditions and annealing temperatures. As a result, the conductivity of CaRuO3 thin films was dependent on CaRuO3 layer thickness and fabrication temperature. We suggested the multi-step deposition, such as two-step deposition with different temperature, to prohibit the NiO formation and to control the hi-axial texture.

• Korean Journal of Materials Research
• /
• v.4 no.4
• /
• pp.459-465
• /
• 1994

A-axis oriened YBCO thin flims were grown on $LaAIO_{3}$ single crystal substrate by off-axis rf magnetron sputtering method. We used two kinds of process to get a-axis oriented fi1ms;one-step process and two-step process. In one-step process, films are grown in single step in which substrate temperature( $T_s$) is in the range of $590^{\circ}C$ to $680^{\circ}C$. On the other hand, in two step process a-axis oriented thin film templates i f about 30nm thickness is deposited at low temperature first, and subsequently films are grown at elevated temperature to the final thickness of about 100nm. In the case of one step process($T_s$ ~)$600^{\circ}C$), prefered a-axis orientation is dominant and Cu-rich phases segregate at the surface. Segregations decrease and ($00 \ell$) peaks increase upon increasing $T_s$. The films prepared by two step method appeared to have strong(h00) peaks as the deposition rate increased. Microstructure shows pin holes resulted from mixed phases of a-axis and c-axis oriented films. In both cases of one step and two step process, as TS decreases, prepared films show stronger a-axis orientation. However electrical properties of the films are depressed with lower $T_c$ and wider $\Delta T$ as $T_s$ decreases.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.81-86
• /
• 2006

We investigated resistance development in $Au/YBa_2Cu_3O_7(YBCO)$ thin film meander lines during high-power faults. The meander lines were fabricated by patterning 300 nm thick YBCO films coated with 200 nm thick gold layers into meander lines. A gold film grown on the back side of the substrate was also patterned into a meander line. The front meander line was connected to a high-power fault-test circuit and the back line to a DC power supply. Resistance of both lines was measured during the fault. They were immersed in liquid nitrogen during the experiment. Behavior of the resistance development prior to quench completion could be understood better by comparing resistance of the front meander lines with that of the back. Quench completion point could be determined clearly. Resistance and temperature at the quench completion point were not affected by applied field strength. The experimental results were analyzed quantitatively with the concept of heat transfer within the meander lines/substrate and to the surrounding liquid nitrogen. In analysis, the fault period was divided into three regions: flux-flow region, region prior to quench completion, and region after quench completion. Resistance was calculated for each region, reflecting the observation for quench completion. The calculated resistance in three regions was joined seamlessly and agreed well with data.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.529-532
• /
• 2003

Quench behavior of resistive superconducting fault current limiters (SFCLs) with various pattern shapes was investigated. The pattern shapes employed were meander, bi-spiral, and spiral shapes of identical line width, gap and margin. SFCLs were fabricated from YBCO thin films grown on two-inch diameter $Al_2O_3$ substrates under the same conditions. Resistance rise of current limiting elements was low at a spiral shape before the whole quench completion, which may act as a disadvantage for simultaneous quench in serial connection between current limiting elements, but the temperature tended to have similar values at higher voltages. On the other hand, bi-spiral shape was severe at insulation level between current limiting lines. When these aspects were considered, we concluded that a meander shape was appropriate to design for a resistive SFCL based on thin films except the concentration of electric field at edge areas of strip lines.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.7
• /
• pp.282-287
• /
• 2003

″H″ type resonator has the advantage for the miniaturization of high-T7 superconducting (HTS) microstrip antenna in comparison with the conventional microstrip antenna such as rectangular type or circular type. In this paper we designed miniaturized HTS antennas using this "H"-type resonator and reported the characteristics of our antennas including return loss, bandwidth, radiation patterns, efficiency and so on. To fabricate the "H" type antenna, HTS YBa$_2$Cu$_3$$O_{7-x}$ (YBCO) thin films were deposited on MgO substrates using rf-magnetron sputtering. For comparison between normal conducting antennas and superconducting antennas, the gold antennas with the same dimension were also fabricated. An aperture coupling was used for impedance matching between 50 $\Omega$ feed line and HTS radiating patch. The ″H" type superconducting antenna showed the performance of 1.38 in SWR, 26 % in efficiency, and 13.8 dB in the return loss superior to the normal conducting counterpart.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.129-132
• /
• 1999

A new single solution source MOCVD technique for the deposition of YBCO film has been developed, using a ultrasonic atomizer to feed the precursors into an evaporation zone. This method being investigated as a basis for future long wire fabrication, for example the electric power use, the magnatic applications, etc.. YBCO films were prepared on MgO(100) substrate, using mixture of Y, Ba, and Cu ${\beta}$ -diketonate chelate was dissolve in tetrahydrofuran as a solution sources. X-ray diffraction measurement indicated that the thin film grew epitaxially with the c-axis orientation perpandicular to the surface of the surface.