• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권8호
• /
• pp.377-386
• /
• 2005

This paper presents the control algorithm of single-phase hybrid active power filter for the compensation of harmonic current components in nonlinear R-L load with passive active Power filters. To construct two phase system, an imaginary second phase was made. In this proposed method, the new signal which is the delayed through the filtering by the phase-delay property of low-pass filter is used as the secondary phase. Because two-phases have the different phase, the instantaneous calculation of harmonic current is possible. In this paper, a reference voltage is created by multiplying the coefficient k by the compensation current using the rotating reference frame synchronized with the source-frequency, not applying to instantaneous reactive power theory which has been used with the existing fixed reference frames In order to verify the validities of the proposed control methods, experiments are carried out with the prototypes of single-phase hybrid active power filter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.189-191
• /
• 2006

This paper analyzes effect of the spinning vehicle on the GPS signal. In rapid spinning vehicles such as missiles and space rockets, carrier phase and frequency depend on the roll rate of the vehicle. It induces phase and frequency modulation caused by the roll rate. The modulated phase and frequency increase dynamic stress error of the tracking loop. Even though higher order tracking loop can remove dynamic stress error, the dynamic stress error can not be remove in this case. In order to analyze the effect of the spinning vehicle on the GPS signal, the experiments are carried out. The experiment results show the modulation of the carrier frequency and phase caused by the roll rate of the spinning vehicle.

• Journal of Power Electronics
• /
• 제14권3호
• /
• pp.598-607
• /
• 2014

This paper proposes a frequency-locked loop (FLL) scheme for a single-phase grid-connected converter. A second-order generalized integrator (SOGI) based on fuzzy logic (FL) is applied to this converter to achieve precise phase angle detection. The use of this method enables the compensation of the nonlinear characteristic of the frequency error, which is defined in the SOGI scheme as the variation of the central frequency through the self-tuning gain. With the proposed scheme, the performance of the SOGI-FLL is further improved at the grid disturbances, which results in the stable operation of the grid converter under grid voltage sags or frequency variation. The PSIM simulation and experimental results are shown to verify the effectiveness of the proposed method.

• Structural Engineering and Mechanics
• /
• 제77권3호
• /
• pp.315-327
• /
• 2021

Here, in this research we have studied a two dimensional problem in a homogeneous orthotropic magneto-thermoelastic medium with higher order dual-phase-lag heat transfer with combined effects of rotation and hall current in generalized thermoelasticity due to time harmonic sources. As an application the bounding surface is subjected to uniformly distributed and concentrated loads (mechanical and thermal source). Fourier transform technique is used to solve the problem. The expressions for displacement components, stress components and temperature change are derived in frequency domain. Numerical inversion technique has been used to obtain the results in physical domain. The effect of frequency has been depicted with the help of graphs.

• 제어로봇시스템학회논문지
• /
• 제2권1호
• /
• pp.35-44
• /
• 1996

A design method for a teleoperator robot system is presented in this paper. The control system consists of two phases; approach phase and contact one. The end-effector position of the estimated slave robot and the contact force between the end-effector and wall are displayed on the monitors at control site, using which the operator controls the teleoperator system. The approach phase controller is designed using Smith's principle and the contact one designed based upon the structured singular value ${\mu}$ in order to increase the robustness of the system. The uncertainatices such as communication time delay and the variations of system parameters are considered as a muliplicative pertubation. Computer simulations are conducted in order to evaluate the performance of the proposed design method. It is found that desirable control performance, especially in the contact phase, is obtained if the control mode is switched into contact phase when the estimated position of the slave robot end-effector is in front of the wall.

• 한국산업융합학회 논문집
• /
• 제4권2호
• /
• pp.149-155
• /
• 2001

The use of primitive cell volume and zero order Laue (ZOLZ) pattern is proposed to identify phase in a complex microstructure. Single convergent beam electron pattern containing higher order Laue zone ring from a nanosized region is sufficient to calculate the primitive cell volume of the phase, while ZOLZ pattern is used to determine the zone axis of the crystal. A computer program is used to screen out possible phases from the value of measured cell volume from convergent beam electron diffraction (CBED) pattern. Indexing of ZOLZ pattern follows in the program to find the zone axis of the identification from a single CBED pattern. An example of the analysis is given from the rapidly solidified $Al-Al_3Ti$ system.

• 국제학술발표논문집
• /
• The 3th International Conference on Construction Engineering and Project Management
• /
• pp.203-211
• /
• 2009

Korean public owners who order public multi-family housing construction projects have yet to gain access to a model for predicting construction cost. For this reason, their construction cost prediction is mainly dependent upon historic data and experience. In this paper, a cost-prediction model based on Case-Based Reasoning (CBR) in the design phase of public multi-family housing construction projects was developed. The developed model can determine the total construction cost by estimating the different Building, Civil, Mechanical, Electronic and Telecommunication, and Landscaping work costs. Model validation showed an accuracy of 97.56%, confirming the model's excellent viability. The developed model can thus be used to predict the construction cost to be shouldered by public owners before the design is completed. Moreover, any change orders during the design phase can be immediately applied to the model, and various construction costs by design alternative can be verified using this model. Therefore, it is expected that public owners can exercise effective design management by using the developed cost prediction model. The use of such an effective cost prediction model can enable the owners to accurately determine in advance the construction cost and prevent increase or decrease in cost arising from the design changes in the design phase, such as change order. The model can also prevent the untoward increase in the duration of the design phase as it can effectively control unnecessary change orders.

• STI Policy Review
• /
• 제1권1호
• /
• pp.93-109
• /
• 2010

Over the last decade, some Korean enterprises have emerged to become global players in their specialized products. How have they achieved such tremendous technological progress in a short period of time? This paper explores that question by examining the characteristics of technological innovation activities at major Korean enterprises. The paper begins with a brief review of the stages of economic growth and science and technology development in Korea. Then, the existing literature, explaining the Korean innovation model, is analyzed in order to establish a new framework for the Korean innovation model. Specifically, Korean firms have experienced three sequential phases, and thus, the Korean model, at the firm level, can be coined as "path-following," "path-revealing," and "path-creating." Then, the stylized facts in the first phase (path-following) and the second phase (path-revealing) are discussed, in the context of empirical evidence from the areas of memory chips, automobiles, shipbuilding, and steel. In terms of technology development, the Korean model has evolved as "collective learning" in the first phase, "collective recombination" of existing knowledge and technology in the second phase, and is assumed as "collective creativity" in the third phase. Ultimately, all three can be classified as "collective creation". Korean firms now face a transition in the modes of technological innovation in order to efficiently implement the third phase. To achieve remarkable progress again, as they did in the past, and to sustain the growth momentum, Korean firms should challenge new dimensions such as creative technological ideas, distinctive technological capabilities, and unique innovation systems -- all of which connote 'uniqueness'. Finally, some lessons from the Korean technological innovation experience are addressed.

• 한국분말재료학회지
• /
• 제12권3호
• /
• pp.208-213
• /
• 2005

Aluminum matrix composites strengthened by the quasi-crystalline (QC) phase were developed in the present study. The icosahedral $Al_{65}Cu_{20}Fe_{15}$ phase was produced by gravity casting and subsequent heat treatment. The mechanical milling process was utilized in order to produce the Al/QC composite powders. The microstructures of the composite powders were examined by optical microscopy (OM) and scanning electron microscopy (SEM). The composite powders were subsequently canned, degassed and extruded in order to produce the bulk composite extrusions with various volume fractions of QC. The microstructure and mechanical properties of the extrusions were examined by OM, SEM, Vickers hardness tests and compression tests. It was found that the microstructures of the Al/QC composites were uniform and the mechanical properties could be significantly improved by the addition of the QC phase.

• Journal of Power Electronics
• /
• 제10권4호
• /
• pp.412-418
• /
• 2010

This paper proposes a new algorithm to generate a reference signal for an active power filter using a sliding-window FFT operation to improve the steady-state performance of the active power filter. In the proposed algorithm the sliding-window FFT operation is applied to the load current to generate the reference value for the compensating current. The magnitude and phase-angle for each order of harmonics are respectively averaged for 14 periods. Furthermore, the phase-angle delay for each order of harmonics passing through the controller is corrected in advance to improve the compensation performance. The steady-state and transient performance of the proposed algorithm was verified through computer simulations and experimental work with a hardware prototype. A single-phase active power filter with the proposed algorithm can offer a reduction in THD from 75% to 4% when it is applied to a non-linear load composed of a diode bridge and a RC circuit. The active power filter with the proposed reference generation method shows accurate harmonic compensation performance compared with previously developed methods, in which the THD of source current is higher than 5%.