• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.222-225
• /
• 2006

The effect of lubrication on the development of textures and Microstructure was studied by different lubricating condition during hot rolling of AA1050 aluminum alloy. Hot rolling without lubrication led to the evolution of the pronounced through-thickness texture gradients, whereas hot rolling with lubrication gave rise to the formation of uniform rolling texture in the whole thickness layer. The variation of texture and microstructure according to hot rolling condition are investigated by X-ray diffractometer (XRD) and Electron Back-Scattered Diffraction (EBSD). The experimental results were discussed base on the finite element method (FEM) simulation. FEM calculation reveals that a larger friction between roll and sheet causes the deviated strain state from a plane strain leading to the formation of shear textures in the thickness layers close to the surface.

• Journal of Magnetics
• /
• v.15 no.1
• /
• pp.32-35
• /
• 2010

The effects of Cu-addition and die-upset temperature on the texture in the die-upset Nd-lean $Nd_xFe_{93.5-(x+y)}-Cu_yGa_{0.5}B_6$ (x = 9-12, y = 0-2) alloys were investigated. The die-upset Cu-containing Nd-lean $Nd_{12}Fe_{81.5-y}-Cu_yGa_{0.5}B_6$ (y = 1, 2) alloys showed a considerable texture. Texture in the Nd-lean alloys developed through basal plane slip deformation. The Cu-addition reduced the melting point of grain boundary phase facilitating grain gliding during the die-upsetting, and providing a greater chance for the $Nd_2Fe_{14}B$ grains to meet the deformation conditions. Die-upsetting at higher temperature facilitated grain gliding and plastic deformation, thus enhancing texture.

• Transactions of Materials Processing
• /
• v.9 no.2
• /
• pp.193-202
• /
• 2000

The influence of rolling draughts on the formation of through-thickness textures in aluminum 5000X sheet was investigated by X-ray texture measurements and microstructure observations. In order to intensify the deformation inhomogeneities, cold rolling was performed without lubrication. Applying a large draught gave rise to the formation of the shear texture at the surface, whereas a normal plane strain testure formed at the surface after deformation with a small draught. The orientation density along the $\beta$-fiber orientations which developed in the center layer of the rolled specimen was also dependent on the strain gradients in a roll gap. Upon annealing, the deformed substructure of sample surfaces was transformed into a fine grained recrystallized microsturcture through extended recovery reaction. However, coarse grains developed after the discontinuous recrystallization which gave rise to the development of the Cube-texture.

• Progress in Superconductivity
• /
• v.7 no.1
• /
• pp.58-63
• /
• 2005

We investigated the surface oxidation behavior of cube-textured polycrystalline nickel at various oxidation conditions. Cube-textured NiO film was formed on a cube-textured polycrystalline nickel regardless of oxidation conditions but different growth behavior of NiO crystals was observed depending on the oxidation conditions. The introduction of water vapor into $O_2$ did not affect the texture evolution, but rough and porous microstructure was developed. Microstructure of NiO film tends to be denser as the oxygen partial pressure increases. It is interesting that (111) peak of theta - two theta diffraction pattern started to get stronger in air atmosphere and (111) plane became the major texture in the substrate oxidized in high purity argon gas. Small amount of high index crystallographic plane NiO peak crystal was observed when $N_{2}O$ was used as an oxidant while only (200) plane crystal was formed in dry $O_2$ atmosphere. Flat and smooth surface was changed into rough faceted one when ramping rate to oxidation temperature was faster. The grain size of NiO was decreased when the oxygen partial pressure was low. It was also observed that the modification of nickel surface suppressed the development of (200) texture.

• Journal of Magnetics
• /
• v.2 no.3
• /
• pp.101-104
• /
• 1997

Vector Moving Preisach model has been applied to the unoriented Co-based alloy thin film media. In the model, the out-of plane easy axis distribution of the particles was derived directly from the texture coefficient phkl obtained from XRD analysis, which corresponds to the fraction of the grains that have the {hkl} plane lying parallel to in-plane direction. The model was validated, by its prediction of a variety of responses, including major loop, minor loop, and the angular dependence of coercivities.

• Progress in Superconductivity
• /
• v.5 no.1
• /
• pp.70-74
• /
• 2003

We fabricated cube textured Ni substrate for YBCO coated conductor and evaluated the effects of processing parameters on microstructural evolution and texture formation. Ni-rods as an initial specimen were prepared by two different methods, i.e., powder metallurgy(PM) and plasma arc melting(PAM). Subsequently, the rods were cold rolled to 100 $\mu\textrm{m}$ thick substrate and annealed at temperatures of $700∼1200^{\circ}C$. The texture of the substrate was characterized by pole-figure. It was observed that the texture of substrate made by P/M did not significantly varied with annealing temperature of 600∼$l100^{\circ}C$ and the full-width at half-maximums (FWHM) of both in-plane and out-of-plane were 9$^{\circ}$∼$10^{\circ}$. On the other hand, the texture of substrate made by PAM was more dependent on the annealing temperature and the corresponding values were $9^{\circ}$ ∼$13^{\circ}$ at the temperature range. In addition, recrystallization twin texture, (221)＜221＞, was formed as the temperature increased further. OM profiles showed that the grain size of substrate made by P/M was smaller than that made by PAM and this difference was correlated to the microstructure of initial specimens.

• Journal of Surface Science and Engineering
• /
• v.31 no.3
• /
• pp.133-141
• /
• 1998

Stainless is widely used for various purposes due to its good corrosion resistance. There has been much research to produce the color stainless steel by several methods. In this experiment, TixN films have been deposited on the SUS304 substrate by the DC magnetron sputtering system and the color and texture of the films as a function of coating conditions has been studies. The TixN films showed a (111) preferred orintation in bias-free conditions. The texture of coated later was changed from (111) to (200) to (2200 with a change of the bias from -1000V to -3000V. When the bias is low, coated elements have low energy. Therefore, the texturct (111) of low surface energy. The mobility of atoms was increased with the increase of the blas and texture was changed to the other plane. Non-etched specimens all exhibited strong (111) texture. This result shows that (111) is a loose plane and of non-etched specimens all exhibited. High growing velocity of (111) of especially was main texture of Non-etched specimens. Low working pressure($4\times10^{-3}$torr) was more effective than figh working pressure ($6\times10^{-3}$torr) for the gold color of $Ti_xN$ film. L and b were increased and a was decreased with the increase of bias voltage. Accordingly, We obtained the near gold color of $Ti_xN$ film(L;92, a;1~1.5 b:24~29.50. As a result of reflectance. And as the bias increased, the reflectance was proportional to the increasing bias voltage, but we took the top reflectance when the bias voltage was -200V.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.75-76
• /
• 2008

In this study, texture development and bending characteristics of strong {0002} textured were observed. AZ31 Mg alloy sheets were prepared along the angle of 0 and 12.5 degrees to the lolling direction or {0002} texture. Prepared samples with different angles to the rolling direction were rolled at room temperature condition and after subsequent heat treatment to investigate texture with x-ray diffractometer, respectively The specimen having along the angles of 0 degree to rolling direction shows the highest load and 12.5 degrees specimen shows the highest displacement among any other specimens in bending test.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.773-776
• /
• 1998

In this paper, we propose an efficient multi-view images coding algorithm which finds the optimal texture from the restricted number of multi-view images. The X-Y plane of the normalized object space is divided into triangular patches. The depth value of the node is determined by applying the block based disparity compensation method and then the texture of the each patch is extracted by applying the affine transformation patch is extracted by applying the affine transformation based disparity compensation method to the multi-view images. We restricted the number of images contributed to determining the texture comapred to traditional methods which use all the multi-view images in the texture extraction. Experimental results show that the SNR of images encoded by the proposed algorithm is better than that of imaes encoded by the traditional method by the amount about 0.2dB for the test sets of multi-view images called dragon, kid, city and santa. The recovered images from the encoded data by the proposed method show the better visual images than the recovered images from the encoded data by the traditional methods.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.5
• /
• pp.1516-1523
• /
• 1996

The present study is concerned with the development of anisotropy and deformation texture in polycrystals. The individual grain in an aggregate is assumed to experience the viscoplastic dedformation with crystallographic slip that unsure uniquenessof the active slip systems and shearing rate onthese systems. Two different methods for updating the grain orientation are examined. Texture development for some deformation modes such as plane strain compression, uniaxial tension and simple shear are found. Changes in anisotropic flow potential due to texture development during large deformation are also given. Anisotropic behavior of polycrystals with defferent textures are examined.