• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.885-886
• /
• 2006

Significant advances in mechanical testing for hard materials are discussed in this paper. There are three specific areas that are covered. In the measurement of fracture toughness factors such as the control of slow crack growth to produce strating cracks, and evaluating reproducibility and repeatability of tests have been recently examined. The miniaturization of tests reduces the amount of material that is used in testing, improves the throughput of tests, and also improves cost effectiveness. New techniques such as stepwise testing and micro scratch testing have contributed to significant additions to the knowledge of the wear mechanisms that operate in these materials.

• Smart Structures and Systems
• /
• v.6 no.7
• /
• pp.851-866
• /
• 2010

This paper presents a new concept of using PZT (lead zircornate titanate) transducers as a non-destructive testing (NDT) tool for evaluating quality of concrete. Detection of defects in concrete is very important in order to check the integrity of concrete structures. The electro-mechanical impedance (EMI) response of PZT transducers bonded onto a concrete specimen can be used for evaluating local condition of the specimen. Measurements are carried out by electrically exciting the bonded PZT transducers at high frequency range and taking response measurements of the transducers. In this study, the compression test results showed that concrete specimens without sufficient compaction are likely to fall below the desired strength. In addition, the strength of concrete was greatly reduced as the voids in concrete were increased. It was found that the root mean square deviation (RMSD) values yielded between the EMI signatures for concrete specimens in dry and saturated states showed good agreement with the specimens' compressive strength and permeable voids. A quality metric was introduced for predicting the quality of concrete based on the dry-saturated state of concrete specimens. The simplicity of the method and the current development towards low cost and portable impedance measuring system, offer an advantage over other NDE methods for evaluating concrete quality.

• Journal of the Korean Society of Safety
• /
• v.29 no.6
• /
• pp.49-54
• /
• 2014

Electrostatic eliminators are essential in various areas of manufacturing industries to protect electrostatic hazards and to reduce inferior products. For ion sources used in the charge neutralizers, there are corona discharge, soft X-ray, and ultraviolet and glow discharge. Among them, corona discharge is generally used, because the corona discharge can easily and economically produce positive and negative ions including electrons in air at atmospheric pressure. But it is necessary to equip explosion-protection electrostatic eliminators wherever hazardous atmosphere. The electrostatic eliminators and their testing method of explosion-protection type have been developed in this research. The contents and scope of the research as follows; developing the type 'Ex s IIB T4' electrostatic eliminator of explosion-protection; developing the type 'Ex s d IIB T4' electrostatic eliminator of explosion-protection; developing the explosion-protection performance testing method of electrostatic eliminator for using AC power source.

• Journal of Information Technology Applications and Management
• /
• v.16 no.3
• /
• pp.17-28
• /
• 2009

This paper presents a novel method for evaluating the usefulness of online product recommendation. Previous studies on evaluating recommendation systems have mostly relied on two methods : testing the accuracy of estimating user preferences by recommendation systems, or empirically testing the effectiveness with lab experiments involving human participants. The former does not measure the usefulness directly and hence can be misleading; the latter is expensive in that it requires a working online store System and test participants. In order to address the problems, the proposed approach uses simulation to imitate customer behavior and evaluate the usefulness of recommendation. Models for user behavior and an abstract Internet store are developed for simulation. Actual simulation experiments are performed to illustrate the use of the approach.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.3
• /
• pp.255-261
• /
• 2007

By using numerical analysis methods, through transmission type pulsed eddy current (PEC) testing is modeled and PEC signal responses due to varying material conductivity, permeability, thickness, lift-off and pulse width are investigated. Results show that the peak amplitude of PEC signal gets reduced and the time to reach the peak amplitude is increased as the material conductivity, permeability, and specimen thickness increase. Also, they indicate that the pulse width needs to be shorter when evaluating the material conductivity and the plate thickness using the peak amplitude, and when the pulse width is long, the peak time is found to be more useful. Other results related to lift-off variation are reported as well.

• Computers and Concrete
• /
• v.3 no.6
• /
• pp.423-437
• /
• 2006

Stress wave propagation through concrete is simulated by finite element analysis. The concrete medium is modeled as a homogeneous material with smeared properties to investigate and establish the suitable finite element analysis method (explicit versus implicit) and analysis parameters (element size, and solution time increment) also suitable for rigorous investigation. In the next step, finite element analysis model of the medium is developed using a digital image processing technique, which distinguishes the mortar and aggregate phases of concrete. The mortar and aggregate phase topologies are, then, directly mapped to the finite element mesh to form a heterogeneous concrete model. The heterogeneous concrete model is then used to simulate wave propagation. The veracity of the model is demonstrated by evaluating the intrinsic parameters of nondestructive ultrasonic pulse velocity testing of concrete. Quantitative relationships between aggregate size and testing frequency for nondestructive testing are presented.

• Journal of KIISE:Information Networking
• /
• v.37 no.6
• /
• pp.494-498
• /
• 2010

Performance requirements of a system are usually closely related to the quality of service provided by the system. The call success rate of a mobile communication system is, for example, directly linked with the quality of call service. Therefore, meeting the performance requirements is one of the critical issues during the operation of services as well as in system development. In this paper, we present a testing method for evaluating the call success rate of a mobile communication system by using interval estimation. Also we analyze the criterion used in the evaluation of the quality of 3G mobile communication services which was recently performed by Korea Communications Commission and then discuss the problems.

• Fire Science and Engineering
• /
• v.21 no.4
• /
• pp.1-11
• /
• 2007

This study aims to investigate, review, and summarize the definition, development, and applications of "percent agent in pipe", "percent of agent in pipe" which is used as a key factor in testing and evaluating the performance of gaseous fire extinguishing agents, including Halon 1301 and $CO_2$. This study also analyzes and compares the local and international standards on testing and evaluating the performance of gaseous fire extinguishing systems, as well as the results of system performance tests conducted as a part of performance evaluation and approval programs for gaseous fire extinguishing systems, especially, Korean Gaseous Fire Extinguishing System Performance Approval Program called KFI Approval. Percent agent in pipe was defined first in NFPA 12A, Standard on Halon 1301 Fire Extinguishing Systems, dating back to the 1970's. After the phaseout of Halon 1301 systems in 1994 in the developed countries, the percent agent in pipe has been widely used in Halon 1301 alternative clean agent fire extinguishing systems, both halocarbon clean agent systems and inert gas clean agent systems, as an essential criterion to assure the system design accuracy, determine the limitations and performance of a system, and to predict the system performance results accurately, especially, in association with their system flow calculations. Underwriters Laboratories has their own standards such as UL 2127 and 2166 applying percent agent in pipe in testing and evaluating the performance of clean agent fire extinguishing systems. As a part of a system performance test and approval program called KFI Approval System, Korea also has started to apply the percent agent in pipe as a key factor to test, evaluate, and approve the performance of gaseous fire extinguishing systems, including both high and low pressure $CO_2$ systems, from the early 2000's. This study outlines and summarizes the relevant UL and KFI standards and also describes the actual test resultant data, including the maximum percents of agent in pipe for gaseous fire extinguishing systems. As evidenced in lots of tests conducted as a part of the system performance test and approval programs like KFI Approval System, it has been proven that the percent agent in pipe may work as a key factor in testing, evaluating, and determining the limitations and performance of gaseous fire extinguishing systems, especially compared with the hydraulic flow calculations of computer design programs of gaseous fire extinguishing systems, and will remain as such in the future. As one thing to note, however, there are some difficulties in using the unified percent agent in pipe to determine the maximum lengths of pipe networks for gaseous fire extinguishing systems, because the varying definitions used by some of the flow calculations (not in accordance with NFPA 12A definition) make it impossible to do any direct comparison of pipe lengths based on percent agent in pipe.

• Journal of Korean Society for Quality Management
• /
• v.36 no.3
• /
• pp.13-21
• /
• 2008

The orthogonality is an important property in the experimental designs. When we use nearly orthogonal arrays(for example, supersaturated designs), we need evaluate the degree of the orthogonality of given nearly orthogonal arrays. We can use the mutual information as a new criterion for evaluating and testing the degree of the orthogonality of given nearly orthogonal arrays.

• Journal of Applied Reliability
• /
• v.17 no.2
• /
• pp.136-142
• /
• 2017

Purpose: In this paper, we propose a test method for evaluating the life time of the inverter which is one of the main internal configuration systems in order to evaluate the life time of the power supply for the vehicle. Methods: The performance and failure criteria required for the development of the accelerated life test method were established and the Taguchi method was used to derive the stress factors affecting performance and reliability. Results: The major stress of the product degradation were considered to be high temperature. Conclusion: The acceleration factor was estimated through a two-level high temperature test and a test methods was designed to guarantee the accelerated life time of the inverter.