• Journal of Environmental Health Sciences
• /
• v.34 no.2
• /
• pp.153-160
• /
• 2008

Personal noise exposure was assessed in railroad operators working in 40 operation units including the Gyeongbu line, Honam line, and Janghang line between 2004 and 2006. 8-hour TWA were assessed based on the MOL (Ministry of Labor) guideline on noise evaluation, and 17% of these measurements exceeded 85 dBA while 70% were over 80 dBA. When the ACGIH TLV is adopted, 40% of measurements were over TLV (85 dBA). The noise exposure risk of railroad operators was higher for diesel locomotive operation and longer operational distances; in addition, the risk was higher for passenger car operation compared to freight car driving. Given that in Korea, over the past 30 years diesel locomotives have provided most of the railway's motive power and that hearing protective equipment is not likely to be used by workers during operation, railroad operators are at a high risk of noise-induced hearing loss. The result of audiometric test among 568 railroad operators showed that 32.6% of those tested had a hearing threshold shift of more than 40 dB. In conclusion, this study calls for more fundamental measures including noise control countermeasures within the operation areas, development of equipment that generates less noise and adopting limitation on the operation distance for a work shift.

• Journal of Environmental Science International
• /
• v.25 no.4
• /
• pp.525-534
• /
• 2016

The biological wastewater treatment plant, which uses microbial community to remove organic matter and nutrients in wastewater, is known as its nonlinear behavior and uncertainty to operate. Therefore, operation of the biological wastewater treatment process much depends on observation and knowledge of operators. The manual inspection of human operators is essential to manage the process properly, however, it is impossible to detect a fault promptly so that the process can be exposed to improper condition not securing safe effluent quality. Among various process faults, equipment malfunction is critical to maintain normal operational state. To detect equipment faults automatically, the dynamic time warping was tested using on-line oxidation-reduction potential (ORP) and dissolved oxygen (DO) profiles in a sequencing batch reactor (SBR), which is a type of wastewater treatment process. After one cycle profiles of ORP and DO were measured and stored, they were warped to the template profiles which were prepared already and the distance result, accumulated distance (D) values were calculated. If the D values were increased significantly, some kinds of faults could be detected and an alarm could be sent to the operator. By this way, it seems to be possible to make an early detecting of process faults.

• Culinary science and hospitality research
• /
• v.9 no.2
• /
• pp.85-97
• /
• 2003

This study is an attempt that Rheology changes are occurred by boiling, frying, and boiling potatoes with soy bean sauce. Three different methods are tested for chemical analysis, fine potato starch grain structural change, sensory evaluation. 1) Alkaline number and acidity number are changed (+)2.17 in raw, decreased (+)1.76 by boiling, increased (+)2.38 by frying, and (-)2.22 by boiling with soy bean sauce. 2) Potatoes are completely dissolved into the gelatinization when they are boiled at 10$0^{\circ}C$ for 15minutes(PB III), fried at 18$0^{\circ}C$ for 3 minutes(PF IV), and boiled with soy bean sauce l0$0^{\circ}C$ for 30 minutes(PS III). 3) The pectin content ratio is decreased according to frying (31.78$\mu\textrm{g}$/$m\ell$), boiling(44.20$\mu\textrm{g}$/$m\ell$), boiling soy bean sauce(36.37 $\mu\textrm{g}$/$m\ell$), Hemicellulose content ratio is decreased according to frying(1.19%), boiling(1.17%), boiling soy bean sauce(0.92%). And the contend of cellulose and lignin is still regardless of any cooking method. 4) The sensory evaluation conducted by 30 university students as panelists showed that there are more significant differences among four samples in appearance, flavour, texture. As a result, the optimum cooking condition for potatoes is that potatoes are boiled l0$0^{\circ}C$ for 15minutes, fried at 18$0^{\circ}C$ for 3minutes, and boiled with soy bean sauce at 1$0^{\circ}C$ for 30minutes.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.2
• /
• pp.41.1-41.1
• /
• 2016

The Galactic center, Sagittarius A* (Sgr A*), is the closest supermassive black hole and emits synchrotron radiation. It provides great opportunity to study the origin of mm/sub-mm emission. Currently, two competing models have been suggested as a jet base and a radiatively inecient accretion flow (RIAF). To unveil the properties, the extremely high resolution(${\sim}10{\mu}as$) corresponding to the projected Schwarzschild radius of ~0.1AU is necessary. With KVN, a jet model can be tested by multi- frequency simultaneous observations because the optically thick surface in a jet (i.e. radio core) moves toward the center at a higher frequency. We conducted 8 observations with KVN at 43/86GHz in 2015, and found that the measured positional shift to the reference calibrator, J1744-3116, was ~0.3 mas to the south of Sgr A* using the source frequency phase referencing (SFPR) at Q/W bands for the first time. With the result, in the future, we will attempt to measure the variation of source position shifts that can constrain the direction of approaching jets and the variability of black hole activity of Sgr A*.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.57-60
• /
• 2005

The objective of this paper is to investigate and analyze the behaviour of prestressed I section structural members constructed with ultra high perfomance steel fiber reinforced cementitious concrete (SFR-UHPC). This material is known as reactive powder concrete (RPC) mixed with domestic materials and its compressive strength is over 150MP. The parameters of test specimens were span to depth ratio, prestressing force, prestressing wire placement and web width. Most influential parameter to determine the failure mode between shear and flexural action was proved to be shear span ratio. The characteristics of ultra high-strength concrete is basically brittle, but due to the steel fiber reinforcement behaviour of this structure member became ductile after the peak load. As a result of the test, the stress block of compressive zone should be redefined. The proposed analytical calculation of internal force capacity based by plastic analysis gave a good prediction for the shear and flexural strength of specimens. The numerical verification of the finite element model which constitutive law developed for Mode I fracture of fiber reinforced concrete correctly captured the overall behaviour of the specimens tested.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.457-460
• /
• 2008

This study evaluated fire resistance performance for polypropylene/steel fiber reinforced high strength concrete column. Full-size columns were constructed and tested with or without fibers using ISO-834 fire curve. As the result of test, non-fiber high strength concrete column specimen occurred serious spalling and indicated rapidly internal temperature increase. Specimen with polypropylene fiber occurred not spalling. Specimen with hybrid fiber occurred not spalling as well as does not propagated temperature propagation. Therefore, hybrid fiber reinforced column specimen indicated a good fire resistance performance than other cases.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.13-16
• /
• 2008

This paper is to present the performance data for improved direct setting method using tile bond for application of porcelain tile under 1 percent absorptance. For this purpose, improved direct setting method type 1 & 2(tile bond curing time 0, 24H) were compared with the conventional setting methods(including direct setting method and improved pressure setting method) in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion, heat ageing(70℃) and freeze-thaw cycle. On the basis of test results, the adhesive strength of direct setting method was lowest for the conventional setting methods. But improved direct setting method using tile bonds(A, B) came close to the result of improved pressure setting method using tile bonds.

• Journal of Technologic Dentistry
• /
• v.29 no.1
• /
• pp.49-57
• /
• 2007

This study was to add crushed frit with different grain sizes to 3Y-TZP so that it could determine the mechanical properties depending on sintering temperature. In this study, 3 types specimens were prepared in powder with respective additions of 20wt.% frit, which was sized through 24-, 48- and 72-hour ball milling with zirconia. Then, sintered pellets were tested in experiments under the temperature variations for different compositions. As a result, this study came to the following findings: 1. It was found that the higher sintering temperature and the longer ball milling time of frit led to the higher sintered density. 2. Bending strength tended to increase with higher sintering temperature and longer ball milling time of frit. 3. Hardness tended to increase with higher sintering temperature and longer ball milling time of frit. 4. However, it was found that fracture toughness didn't vary significantly depending on sintering temperature. From these findings, it was concluded that the smaller frit grain size and the narrower particle size distribution of frit lead to the better mechanical properties.

• The KSFM Journal of Fluid Machinery
• /
• v.19 no.5
• /
• pp.5-11
• /
• 2016

The purpose of this study is to design the transonic centrifugal compressor impeller with splitter blades and analyze the flow fields with respect to various splitter blades. Seven impellers with different splitter chord length or pitchwise location were tested by using CFD method. To investigate aerodynamic performance, Mach number distribution and entropy distribution were confirmed. As a result, it is found that the size of transonic region and shock wave location are related to the splitter chord length and pitchwise location. Also the impeller with long chord length of splitter shows higher total pressure ratio but lower efficiency than those of the impeller with short chord length of splitter. In terms of pitchwise location, the impeller with the splitter located in mid-pitch of main blades shows the best performance with respect to pressure ratio and efficiency.

• Journal of Korean Academy of Nursing Administration
• /
• v.14 no.3
• /
• pp.219-228
• /
• 2008

Purpose: The purpose of this study was to develop a measurement scale of nursing competence for nurses working in general wards, and to test the validity and reliability of the scale. Method: A methodological study design was used, consisting of 3 steps as conceptual framework decision, measurement items development, and testing of validity and reliability. In order to verify content validity, 16 experts reviewed the concept of each competences and measurement items. The developed measurement items were tested from 301 nurses in one hospital. Factor analysis and item analysis were applied to establish the scale's construct validity and reliability. Result: The final scale consists of nine dimensions with 70 items. The overall scale reliability had a Cronbach's alpha of 0.98, and the demensions Cronbach's alpha ranged from 0.88 to 0.95. The factor loading of construct validity was from 0.40 to 0.83. The explained variance from the 9 extracted factors was 70.93% of the total variance, and final factors were labeled as critical thinking, resources management and professional development, ability of ward management, application of nursing process, ethical accountability, respectful consideration, patient centered approach, crisis management, and leadership. Conclusion: This measurement scale can be utilized to evaluate nursing competence for nurses working in general wards.