Journal of the Korea Academia-Industrial cooperation Society
/
v.4
no.1
/
pp.7-12
/
2003
The purpose of testability analysis is to estimate the difficulty of testing a stuck-at fault in logic circuits. A good testability measurement can give an early warning about the testing problem so as to provide guidance in improving the testability of a circuit. There have been researches attempting to efficiently compute the testability analysis. Conventional testability measurements, such as COP and SCOAP, can calculate the testability value of a stuck-at fault efficiently in a tree-structured circuit but may be very inaccurate for a general circuit. The inaccuracy is due to the ignorance of signal correlations for making the testability analysis linear to a circuit size. This paper proposes an efficient method for computing testability analysis, which takes into account signal correlation to obtain more accurate testability. The proposed method includes the algorithm for identifying all reconvergent fanouts in a given n circuit and the gates reachable from them, by which information related to signal correlation is gathered.
Kim, Sung-Il;Yang, Sun-Woong;Kim, Moon-Joon;Park, Jae-Heung;Kim, Seok-Yoon;Chang, Hoon
Journal of KIISE:Computer Systems and Theory
/
v.30
no.2
/
pp.99-107
/
2003
This paper proposes a design for testability (DFT) and testability analysis method for register-transfer level (RTL) circuits. The proposed method executes testability analysis - controllability and observability - on the RTL circuit and determines the insertion points to enhance the testability. Then with the associated priority based on the testability, we insert only a few of the test multiplexers resulting in minimized area overhead. Experimental results shows a higher fault coverage and a shorter test generation time than the scan method. Also, the proposed method takes a shorter test application time required.
Journal of the Institute of Electronics Engineers of Korea SD
/
v.41
no.5
/
pp.81-90
/
2004
This paper presents new testability measure based on learning, which can be useful in the deterministic process of test pattern generation algorithms. This testability measure uses the structural information that are obtained by teaming. The proposed testability measure searches for test pattern that can early detect the conflict in case of the hardest decision problems. On the other hand in case of the easiest decision problem, it searches for test pattern that likely results in the least conflict. The proposed testability measure reduces CPU time to generate test pattern that accomplishes the same fault coverage as that of the distance-based measure.
Journal of the Korean Institute of Telematics and Electronics
/
v.18
no.5
/
pp.30-34
/
1981
This paper deals with the testability evaluation method for the digital systems. This method uses two factors: the complexity and the accessibility. The complexity depends on the ratio in combinational and sequential circuits, number of input/output terminals, and the circuit count by using the gate input level method. The accessibility is how easily to handle the data from I/O terminals. The system testability has a normalized value. Thus, analyzing the testability evaluation, and redesigning the circuit to improve testability, the systems increase interests for the maintenance and have high reliability. Finally, in comparison with Stephenson and Grason's technique, this technique gives sufficiently accurate results for much less computation effort.
This paper presents a new data path synthesis algorithm which takes into account simultaneously three important design criteria: testability, design area, and total execution time. We define a goodness measure on the testability of a circuit based on three rules of thumb introduced in prior work on synthesis for testability. We then develop a stepwise refinement synthesis algorithm which carries out the scheduling and allocation tacks in an integrated fashion. Experimental results for benchmark and other circuit examples show that we are able to enhance the testability of circuits with very little overheads on design area and execution time.
In this thesis, we present efficient techniques to reduce the switching activity in a CMOS combinational logic network based on local logic transforms. But this techniques is not appropriate in the view of testability because of deteriorating the random pattern testability of a circuit. This thesis proposes a circuit design method having two operation modes. For the sake of power dissipation(normal operation mode), a gate output switches as rarely as possible, implying highly skewed signal probabilities for 1 or 0. On the other hand, at test mode, signals have probabilities of being 1 or 0 approaching 0.5, so it is possible to exact both stuck-at faults on the wire. Therefore, the goals of synthesis for low power and random pattern testability are achieved. The hardware overhead sof proposed design method are only one primary input for mode selection and AND/OR gate for each redundant connection.
Journal of Electrical Engineering and information Science
/
v.3
no.1
/
pp.8-13
/
1998
Often ESOP(Exclusive Sum of Products) expressions provide more compact representations of logic functions and implemented circuits are known to be highly testable. Motivated by the merits of using XOR(Exclusive-OR) gates in circuit design, ESOP(Exclusive Sum of Products) expressions are considered s the input to the logic synthesis for random pattern testability. The problem of interest in this paper is whether ESOP expressions provide better random testability than corresponding SOP expressions of the given function. Since XOR gates are used to collect product terms of ESOP expression, fault propagation is not affected by any other product terms in the ESOP expression. Therefore the test set for a fault in ESOP expressions becomes larger than that of SOP expressions, thereby providing better random testability. Experimental results show that in many cases, ESOP expressions require much less random patterns compared to SOP expressions.
Journal of the Korean Institute of Telematics and Electronics C
/
v.35C
no.11
/
pp.11-20
/
1998
Testability analysis computes controllabilities and observabilities of all lines of a circuit and then evaluates fault coverage. The values of controllability and observability as well as fault coverage produced by testability analysis are used for applications of testability analysis. ITEM was evaluated as a fault coverage tool. But the values of controllability and observability at all lines of circuits must be estimated as a performance measure of testability tools for another application such as partial scan. In this paper, partial scan method based on sensitivity analysis which estimates relative improvement of detectability of circuits after scanning a flip-flop is used for performance evaluation of ITEM. Performance of ITEM, with respect to testability values on each net, has been measured by comparing ITEM and STAFAN. Partial scan performance achieved by ITEM is very similar to that of STAFAN, but ITEM takes less CPU time. Therefore ITEM is very efficient for partial scan application because ITEM runs faster for very large circuits in which execution time is critical.
The Journal of Korean Institute of Communications and Information Sciences
/
v.15
no.9
/
pp.745-752
/
1990
This paper deals with the path sensitization algrithm from PI to PO center on the nodes of high testability mainstay when CUT is tested by pseudo exhaustive testing. In CUT, the node definition of high testability mainstay treats the testability values of the entire nodes with the population composed of the raw data, and after we examined the level of significance(1-a) region, we accomplished in the estimation of the confidence interval of the testability. Focusing on the defined nodes of high testability mainstay, we performed the singular cover and consistency operation to the forward and backward logic gates. Thus, we easily generated the pseudo exhausitve test patterns. As a result, (1-a) region has 0.1579 and the pseudo exhaustive test patterns are least generated and the rate of test pattern is 1.22%, compared with exhaustive testing. (1-a) region has 0.2368 and this results exhibits the optimal performance of the singular cover and consistency operation. Applying the generated pseudo exhaustive test patterns to the stuck-at faults existing on the inputs and internal nodes in CUT, we verified this performance on the output. Thus, it is confirmed that functional testing of the proposed path sensitization algorithm is very useful.
Journal of the Korean Institute of Telematics and Electronics A
/
v.32A
no.4
/
pp.75-84
/
1995
Fault simulators are used for accurate evaluation of fault coverages of digital circuits. But fault simulation becomes time and memory consuming job because computation time is proportional to wquare of size of circuits. Recently, several approximate algorithms for testability analysis have been published to cope with the problems. COP is very fast but cannot be used for sequential circuits, while STAFAN can ve used for sequential circuits but requires large amount of computation because it utilizes logic simulation results. In this paper EXTASEC(An Extension of Testability Analysis for Sequential Circuits) is proposed. It is an extension of COP in the sense that it is the same as COP for combinational circuits, but it can handle sequential circuits, Xicontrollability and backward line analysis are key concept for EXTASEC. Performance of EXTASEC is proven by comparing EXTASEC with a falut simulator, STAFAN, and COP for ISCAS circuits, and the result is demonstated.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.