• Journal of Preventive Medicine and Public Health
• /
• 제29권4호
• /
• pp.785-799
• /
• 1996

절삭유의 사용과 피부질환의 관계를 알아보기 위하여 한 자동차공장의 엔진 및 구동부서 근로자 1,004명을 대상으로 피부 이상 증세에 대한 기초설문조사를 실시하여 응답을 해준 근로자 667명을 대상으로 분석 및 피부과적 검진을 실시하였다. 또한 절삭유의 노출 정도를 알기 위한 방법으로 공기 중 오일 미스트를 측정하였다. 이 조사의 결과를 요약하면 다음과 같다. 1. 공기 중 오일미스트는 3개 부서로 나누어서 측정 하였는데, 전체 52건의 측정건수 중에서 8시간가중 평균 기준치인 $5mg/m^3$을 넘는 건수는 9건(17.3%)이었고, 로그정규분포상에서 95% 신뢰한계의 전체 상한치는 기준치 미만이었다. 2. 조사한 부서는 엔진가공부(258명), 가솔린 엔진조립부(210명), 디젤엔진조립부(96명), 구동부 가공반(86명), 구동부 조립반(17명)의 5개 부서였으며, 조사한 667명의 평균 나이는 34.5세였고, 근무연수의 중앙값은 7년 7개월이었다. 3. 이들 부서 중 엔진가공부와 구동부 가공반(A군)은 절삭유를 공정상 많이 사용하는 부서로 근로자 344명 중 298명 (86.6%)이 한 가지 이상의 절삭유를 사용하고 있는 반면, 가솔린엔진 조립부, 디젤엔진 조립부, 구동부 조립반의 근로자 323명(B군) 중에는 31명 (9.1%)만이 절삭유를 사용하고 있었다. 4. 피부 이상 증세의 경험자 227명 중 213명에 대하여 피부과전문의의 진찰을 시행하였는데, 이중에 172명이 검진당시 증세를 호소했는데, 1인당 평균 호소증세 건수가 1.5건 정도였다. 가장 많은 증세는 가려움증(32.5%), 구진(21.6%), 인설(15.7%), 소수포(12.5%), 반점(9.4%)의 순서였다. 5. 검진을 받은 근로자 231명 중 정상소견이나 뚜렷한 병변이 없는 사람으로 분류된 경우는 53명이었고, 나머지 160명에서 피부과적 질환이 발견되었다. 가장 많은 것은 접촉 피부염으로 전체 질환자 중 92명 (57.5%)을 차지하였고, 이들 중에는 여드름이나 낭포염 등 기타 다른 피부질환을 동반한 경우가 23명 (25%) 이었다. 기타 낭포염, 여드름만 있는 경우도 각각 9명(5.6%), 8명(5.0%)이었으며 , 각질화와 색소 이상도 1명 씩 발견되었다. 기타의 수부 습진은 비특이성 수부습진으로 분류되었는데 이들은 47명이었다. 6.피부질환이 있다고 진단받은 160명에서 발견된 피부과적 이상부위는 1인당 1.3부위였다. 이상이 발견된 부위는 손바닥(27.6%), 손가락과 손톱(22.7%), 상박부(16.0%), 손등(11.8%), 손가락 사이(10.3%)의 순이었고, 이들 수부 및 상박부위의 이상이 전체 이상의 약 88.7%였다. 7. 전체 피부질환의 유병상태는 각 부서별로 차이가 많았는데, 특히 접촉 피부염의 경우 엔진가공부는 1,000명당 213명, 가솔린엔진 조립부는 1,000명당 29명, 디젤엔진 조립부는 1,000명당 73명이었고, 구동부 가공반은 1,000명당 267명, 구동부 조립반은 1,000명당 59명으로 부서별로 차이가 매우 켰다. 이러한 경향은 절삭유 사용에 따라서 특히 수용성 절삭유만 사용하는 군과 두 종류의 절삭유를 모두 사용하는 근로자에서 마찬가지로 높게 관찰되었다. 8. 감별진단이 필요하다고 판단된 접촉 피부염 환자 49명은 첩포 검사를 시행하였다. 첩포 검사 결과, 기본 표준시료에 양성이 나타난사람이 12명, 기본표준시료와 오일시료에 모두 양성이 나타난 사람 3명, 그리고 오일 시료에만 양성이 나타난 사람 3명이 있었고, 기본 표준시료와 유기용제시료에 양성이 나타난 사람, 유기용제 시료에만 양성이 나타난 사람이 각각 1명 있었다. 9. 전체 피부질환의 유무에 대하여, 근로자의 나이와 근무기간의 영향을 통제한 후 근로자들이 사용하는 절삭유의 종류에 따른 위험도를 알아보기 위하여 다변량 분석을 하였다. 분석결과 절삭유를 전혀 사용하지 않는 군과 비수용성 절삭유만을 사용하는 군과는 유의한 차이가 없었으며 수용성 절삭유만 사용하는 사람은 $1.4\sim3.3$배(교차비의 95%신뢰한계), 두 종류의 절삭유를 모두 사용하는 사람은 $1.9\sim4.1$배 정도로 위험도가 높았다. 10. 알레르기성 접촉 피부염을 종속변수로 같은 분석을 했을 때도 결과는 같았으나, 수용성 절삭유만 사용하는 군이 $2.7\sim9.7$배, 두 종류를 모두 사용하는 군에서는 $3.7\sim12.6$배 정도로 위험도가 증가한 것을 관찰할 수 있었다.

• 한국지반공학회논문집
• /
• 제35권5호
• /
• pp.5-19
• /
• 2019

암반으로 구성되어 있는 급경사($65^{\circ}{\sim}85^{\circ}$)비탈면이 장기간 안정한 상태로 유지되고 있는 자연현상을 고려할 때, 설계 및 초기 시공 단계에서 위와 유사한 지반 상태로 이루어진 깎기 암반비탈면에 대해 1:0.5(발파암 경사 기준)보다 급한 경사를 적용할 수 있을 것이다. 급경사로 설계 가능한 양호한 연속체 암반비탈면의 안정성을 검토하는 과정에서, 설계실무 측면에서 범용적인 암반강도정수 산정방법이 필요하게 되었다. Hoek 등(2002)이 수정 보완하여 발표한 Hoek-Brown 파괴기준과 GSI분류는 불연속구조의 영향을 충분히 고려한 암반특성화 시스템으로 평가되었으며, 응력변화에 따라 등가 Mohr-Coulomb 강도정수(등면적법)를 산출하는 방법을 제안하였다. 비탈면에서는 등가 M-C 강도정수가 최대구속응력(${{\sigma}^{\prime}}_{3max}$ 또는 수직응력)변화에 따라 민감하게 변화하므로 실무적으로 활용하기에 어려운 점이 있다. 이 연구에서는 양호한 연속체 암반비탈면에 대해 최대구속응력 범위이내에서 범용적으로 적용할 수 있는 강도정수산정방법(등각분할법)을 H-B 파괴기준을 응용하여 제안한다. 등각분할법 강도정수(A)의 타당성 및 적용성을 평가하기 위해, 연구대상 암반비탈면을 기존 실시설계 현장 인근에 있는 급경사 비탈면에서 암석종류별(화성암, 변성암, 퇴적암)로 선정하고, Hoek이 제시한 등가 M-C 강도정수(등면적법)들과 비교 분석하였다. 등면적법 및 등각분할법 등가 M-C 강도정수는 기본적인 자료인 기존 실시설계 현장의 실내 암석 삼축압축시험과 연구대상 암반비탈면의 불연속구조의 특성조사(Face Mapping)를 통해 RocLab 프로그램(H-B 파괴기준을 기본으로 전산화된 지반정수 산정 소프트웨어)을 활용하여 산정하였다. 산정된 등면적법 등가 M-C 강도정수는 상호 연동되어 점착력과 내부마찰각이 아주 크거나($45^{\circ}$ 이상) 작게 나타났다. 등각분할법 등가 M-C 강도정수는 등면적법 등가 M-C 강도정수의 중간 정도이며, 내부마찰각은 $30^{\circ}{\sim}42^{\circ}$의 범위를 보인다. 연구대상 암반비탈면의 등각분할법 강도정수(A)와 기존 실시 설계 현장에서 연구대상 암반비탈면과 유사한 암반상태(동일 등급 RMR)에 적용한 강도정수(B)와 비교 분석하고, 이 지반정수들로 적용한 비탈면 안정해석(한계평형해석과 유한요소해석) 결과를 통해 제안한 등각분할법의 적용성을 간접적으로 평가하였다. A와 B의 강도정수 차이는 10% 정도이다. 한계평형해석 결과(우기 기준), A적용 안전율(Fs)=14.08~58.22(평균 32.9), B적용 안전율(Fs)=18.39~60.04(평균 32.2)이며, 각 동일한 암석종류에 따라 상호 유사하게 나타났다. 유한요소 해석 결과, A적용 변위=0.13~0.65mm(평균 0.27mm), B적용 변위=0.14~1.07mm(평균 0.37mm)으로 매우 유사하다. H-B 파괴기준을 응용하여 등각분할법으로 산출한 지반 정수를 실무적인 전단강도로 적용할 수 있는 적용성 평가에서 유의미한 결과를 확인할 수 있었다.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• 제1권1호
• /
• pp.56-78
• /
• 1998

연구목적: 만성 B형 간염의 간조직 소견은 진단 및 예후의 평가 뿐아니라 치료여부의 결정 및 치료효과의 평가를 위해서 중요하고, 이는 좀 더 객관적, 구체적, 포괄적으로 새롭게 분류할 필요성이 있다. 우리나라 소아의 만성 B형 간염의 빈도는 높을 것으로 추정되는데 아직 이에 대한 병리조직학적 고찰은 거의 없는 상태이다. 이에 저자들은 점수로 평가한 최근의 반정량적 분류 방법(Ludwig 분류법)을 전통적으로 이용되어온 De Groute의 분류법과 비교하여 연관성을 밝히고, 반정량적 분류법이 좀 더 객관적으로 예후를 예견하고 형태학적 변화를 감시하는 유용한 방법임을 소개하고자 하였다. 대상 및 방법: 서울대학교병원 소아과에 입원하여, 간조직 생검을 받은 만성 B형 간염 환아 99명을 대상으로 병리조직 소견과 병록지 고찰을 시행하였다. B형 간염 표식자로는 HBsAg, anti-HBs, HBeAg, anti-HBe, anti-HBc(IgG, IgM), HDV를 방사면역측정(radioimmunoassay)을 이용하여 검사하였다. 간생검조직은 전통적인 De Groute의 병리조직학적 분류법과 병리조직학적 변화를 문맥강 및 문맥강 주변의 염증(Portal/Periportal activity), 간소엽 내 염증(Lobular activity), 섬유화(Fibrosis)로 나누어 각각의 정도를 0에서 4로 점수화(Numerical scoring)한 Ludwig의 체계에 따라 분류하였다. 두가지 분류법 간의 연관성과, 병리조직 소견에 따른 빈도, 연령 및 성별 분포, 임상적 특징, 생화학적 및 혈청학적 검사 소견을 비교 조사하였다. 또한 간세포암 5례는 따로 분류하여 임상적 고찰을 시행하였다. 결 과: 1) 총 99례 중 남아 83례, 여아 16례였고, 연령별 분포는 1년 5개월에서 16년 4개월까지였으며, 평균연령은 9.4세였다. 병리조직형별 연령 및 성별분포에는 차이가 없었다. 2) 병리조직형별 분포는 정상 조직 소견 2례, 만성 소엽성 간염 2례, 만성 지속성 간염 22례, 경도 만성 활동성 간염 40례, 중등도 만성 활동성 간염 19례, 고도 만성 활동성 간염 1례, 간경변을 동반한 만성 활동성 간염 7례, 간경변증 1례, 간세포암 5례였다. 두가지 분류법은 높은 연관성을 보였으나 간경화의 경우는 연관성이 떨어져서, 간조직내 염증과 섬유화는 따로 분리하여 평가하거나, 섬유화의 중량이 필요함을 알 수 있었다. 3) 간세포암을 제외한 94례 중 66례(70%)가 신체검사에서 우연히 발견된 경우였으며, 2례는 전신 부종이 주소로서 B형 간염과 관련된 막성 사구체 신염이 동반되어 있었다. 그 외는 비특이적인 간염증상을 주소로 내원하여 진단되었다. 내원시 임상 증상으로는 이피로성, 식욕부진, 오심, 구토, 복통, 복부팽만, 체중감소, 발열, 진한 소변색, 황달, 비출혈, 부종, 혈뇨 등이 있었고, 이학적 소견으로는 간장비대, 비장비대, 우측 상복부통이 있었다. 병리조직형별 임상증상, 이학적 소견 및 그 빈도에는 차이가 없었다. 4) 총 99례 중 가족력상 어머니에 B형 간염의 병력이 있는 경우가 54례, 아버지가 12례, 형제들의 경우가 25례 있었으며, 그 외의 동거 가족에서 가족력이 있는 경우는 17례 있었고, 가족력이 없는 경우는 28례였다. 가족 중 간경화가 있는 경우는 9례였고, 간세포암도 2례에서 있었다. 어머니가 만성 활동성 간염으로 사망한 례가 1례 있었고, 형제가 전격성 간염으로 사망한 경우도 1례 있었다. 병리조직형별 가족력의 차이는 없었다. 5) 간기능 검사소견을 보면, AST와 ALT의 평균은 각각 $151{\pm}158$ U/L, $215{\pm}221$ U/L이고, 병리조직형별로는 조직 염증소견이 심할수록 유의하게 높은 것을 알 수 있었다. 그러나 병리조직형별로 중복되는 부분이 많아 AST, ALT치로 조직형을 예측하는 것은 어려웠다. Ludwig의 분류와 간기능 검사치와의 관계를 보면, 혈청 알부민은 섬유화가 진행할수록 유의하게 감소하는 것을 관찰할 수 있었고, ALT, AST는 간조직내 염증 및 섬유화가 심할수록 유의하게 증가하는 것을 관찰하였다. 6) Prothrombin time은 조직형이 심할수록 유의하게 길어졌고, 특히 간경화가 진행될수록 나빠지는 것을 관찰할 수 있었다. APTT(activated partial thromboplastin time)도 조직형이 심할수록 길어지는 것을 관찰할 수 있었으나, 통계적 유의성은 없었다. 반정량적 방법에 의한 분류와의 관계를 보면, Prothrombin time과 APTT는 간조직내 염증 및 섬유화가 심할수록 길어지는 것을 관찰하였으나, 통계적 유의성은 없었다. 7) IgM anti-HBc는 검사가 이루어진 80명 중 1명에서만 양성이었고, HDV는 검사가 이루어진 83명 중 양성인 경우는 한 례도 없었다. HBeAg은 간생검 당시 81례에서 양성이였고, 이 후 평균 $41.8{\pm}31.3$개월간의 추적 중에 HBeAg 음전을 보인 경우는 50례가 있었고, 1년 음전율은 37%였다. 병리조직형별로는 조직형이 심할수록 음전시까지의 기간이 짧은 것을 관찰할 수 있었다. 8) 간세포암 5례의 남녀 분포는 남아 4례, 여아 1례이고, 평균연령은 $10.4{\pm}3.1$세(7세~13세 6개월)였다. 모두에서 HBsAg양성, HBeAb양성과 어머니의 만성 B형 간염의 가족력이 있었다. 간세포암 주변 조직 소견은 1례를 제외하고는 모두에서 간경화의 소견을 보였다. 추적 중 혈청 AFP의 증가로 조기발견된 1례는 종양절제술 후 항암요법으로 추적 중에 있고, 그 외에는 모두 수술 후 항암요법 혹은 방사선요법을 병행하여 시행했으나 사망하였다. 결 론: 만성 B형 간염의 간손상 정도는 임상증상이나 생화학적 검사소견으로 평가할 수 없었고, 간조직검사에 의한 병리조직학적 분류가 필요하였다. 이는 De Groute의 분류와 잘 연관되는 반정량적 Ludwig 방법에 의해 좀 더 포괄적, 구체적, 객관적으로 분류할 수 있었고, 후자는 예후를 예견하고, 형태학적 변화를 감시하며, 통계적으로 분석하는 데 유용한 방법임을 시사하였다.

• 농업과학연구
• /
• 제4권2호
• /
• pp.283-316
• /
• 1977

한국(韓國)에 있어서 벼 잎집무늬마름병(病)의 발생변동(發生變動), 병원균(病原菌)의 배양적(培養的) 특성(特性)과 병원성(病原性), 발병환경(發病環境), 재배법(栽培法)과 발병관계(發病關係), 품종(品種)의 저항성(抵抗性) 등(等)에 관(關)하여 연구(硏究)한 결과(結果)를 요약(要約)하면 다음과 같다. 1. 한국(韓國)에 있어서 벼 잎집무늬마름병(病)의 발생면적(發生面積)은 다비재배(多肥栽培), 조기조식재배(早期早植栽培) 및 통일계품종(統一系品種)의 확대보급등(擴大普及等)으로 인(因)하여 매년(每年) 증가(增加)되었고 특(特)히 1971년(年)부터 전국적(全國的)으로 급격(急激)히 발생면적(發生面積)이 증가(增加)되어서 1976년(年)에는 전체수도재배면적(全體水稻栽培面積)의 약 65.2%에서 본병(本病)이 발생(發生)하였다. 2. 우리나라에 분포(分布)하는 벼 잎집무늬마름병균(病菌)의 배양적(培養的) 성질(性質) 및 병원성(病原性)에는 많은 변이(變異)가 있었으며 병원균(病原菌)의 생육최적(生育最適) 온도(溫度)도 $25^{\circ}C$에서 $30^{\circ}C$사이로 균주간(菌株間)에 차이(差異)가 있었다. 한편 병원균(病原菌)의 배양적(培養的) 성질(性質)과 병원성(病原性)에는 상관관계(相關關係)가 없었다. 3. 잎집무늬마름병균(病菌)의 PDA배지상(培地上)에서의 균사생장(菌絲生長)은 채집지(採集地)의 기온(氣溫)과 밀접(密接)한 관계(關係)가 있었다. 즉 채집지(採集地)의 기온(氣溫)이 높은 지역(地域)의 균주(菌株)들은 기온(氣溫)이 낮은 지역(地域)의 균주(菌株)들에 비(比)해 $35^{\circ}C$ PDA배지(培地)에서 균사생장(菌絲生長)이 양호(良好)하였고 반대로 $12^{\circ}C$ PDA배지상(培地上)에서는 기온(氣溫)이 낮은 지역(地域)에서 채집(採集)한 균주(菌株)들이 기온(氣溫)이 높은 지역(地域)에서 채집(採集)한 균주(菌株)들 보다 균사생장(菌絲生長)이 양호(良好)하였다. 4. 잎집무늬마름병균(病菌)을 접종(接種)한 수도엽(水稻葉)으로부터 얻은 Pectin polygalacturonase 및 Cellulase의 역가(力價)는 접종(接種)3일(日)째에 최대(最大)였고 Pectin methylestrase의 역가(力價)는 접종(接種) 4일(日)째에 최대(最大)였으며 병원성(病原性)이 강(强)한 균주(菌株)에서는 Pectin methylestrase의 활성(活性)이 높은 경향(傾向)이었고 병원성(病原性)이 약한 균주(菌株)에서는 Pectin methylestrase의 활성(活性)이 낮은 경향(傾向)이었으나 다른 효소(酵素)들은 병원성(病原性)과 관계(關係)가 없었다. 5. 배지(培地)에 형성(形成)된 균핵(菌核)을 건조처리(乾燥處理)하였을 경우(境遇)의 저온저항성(低溫抵抗性)은 매우 강(强)하여 $-20^{\circ}C$에서도 발아력(發芽力)을 상실(喪失)치 않았으나 습윤처리(濕潤處理) 하였을 경우(境遇)에는 저항성(抵抗性)이 매우 약(弱)하여 $-5^{\circ}C$에서도 발아력(發芽力)을 상실(喪失)하였다. 포장(圃場)에서 월동(越冬)한 균핵(菌核)의 발아율(發芽率)도 답토양(沓土壤)의 건습(乾濕)에 따라 18%~70%의 차이(差異)를 나타내며 담수상태(湛水狀態)에서 월동(越冬)한 균핵(菌核)은 건조(乾燥)한 토양(土壤)에서 월동(越冬)한 균핵(菌核)보다 발아율(發芽率)이 낮았다. 6. 잡초(雜草)에 대(對)한 기생성(寄生性)을 조사(調査)하였던 바 벗풀(Sagittaria trifolia L.), 물달개비(Monochoria vaginalis Presl), 여뀌(Polygonum hydropiper L.). 피(Echinochloa crusgalli P. Beauv), 한련초(Eclipta prostrata L.), 강아지풀(Septaria viridis P. Beauv.), 좀바랭이(Digitaria sangvinalis Scapoli) 등(等)에서 잎집무늬마름병반(病斑)이 형성(形成)되었다. 7. 질소배비구(窒素倍肥區)에서는 잎집무늬마름병(病)의 피해(被害)가 증가(增加)하였고 가리배비구(加里倍肥區)에서는 감소(減少)하였으나 규산시용구(硅酸施用區)에서는 피해감소(被害減少)의 효과(效果)가 없었다. 규산시용구(硅酸施用區)에서는 도체내(稻體內)의 질소함량(窒素含量)과 전분함량(澱粉含量)이 다같이 감소(減少)하였다. 8. 생육전기(生育前期)의 이병경율(罹病莖率)은 밀식구(密植區)가 높았으나 생육후기(生育後期)에는 소식구(疎植區)의 1주당(株當) 분얼수(分蘖數)가 많아 이병경율(罹病莖率) 및 피해도(被害度)가 높아졌으며 주당(株當) 1본식(本植)한 구(區)에서는 피해(被害)가 적었다. 9. 잎집무늬마름병(病)에 대(對)한 수도(水稻) 품종(品種)의 피해도차이(被害度差異)는 출수일수(出穗日數)와 밀접(密接)한 관계(關係)가 있었다. 즉 출수일수(出穗日數)와 피해도(被害度)와의 상관관계(相關關係)는 6월(月)13일(日) 이앙(移秧)한 구(區)에서는 r=-0.707이었고 6월(月) 25일(日) 이앙(移秧)한 구(區)에서는 r=-0.496으로 비교적 높은 상관(相關)을 나타내어 출수(出穗)가 빠른 것이 피해(被害)가 크고 낮은 것이 피해(被害)가 적은 경향(傾向)이었다. 또한 본병(本病)은 분얼(分蘖)이 많은 품종(品種)일수록 피해(被害)가 심(甚)하였다. 10. 생육전기(生育前期)의 이병경율(罹病莖率)은 출수후(出穗後)의 피해도(被害度)와 상관(相關)이 없었으나 생육후기(生育後期)의 이병경율(罹病莖率)은 피해도(被害度)와 상관(相關)이 높았다.

• 한국가정과교육학회지
• /
• 제24권2호
• /
• pp.117-134
• /
• 2012

본 연구의 목적은 가정과교육에서 창의 인성 교육에 대한 가정과 교사의 관심 단계와 실행 수준, 그리고 실행 실태를 알아보는데 있다. 연구 자료는 전국의 중학교 가정과 교사를 대상으로 체계적 표집과 편의 표집을 하여 우편과 이메일을 통해 설문지를 배포하고 회수된 187부를 최종 분석에 사용하였다. 조사 도구는 주로 Hall(1987)이 개발한 혁신에 대한 교사의 관심도와 실행 수준에 대한 질문지를 수정 보완하여 사용하였고 그 외는 선행연구를 기초하여 개발하였으며 타당도와 신뢰도를 검증하였다. 자료는 SPSS/window(12.0) 프로그램을 이용하여 빈도, 백분율, 평균, 표준편차, t-test, ANOVA를 실시하였다. 본 연구를 통해 밝혀진 결과를 요약하면 다음과 같다. 첫째, 창의 인성 교육에 대한 가정과 교사의 관심 단계는 정보적 관심 단계(85.51)가 가장 높았으며 다음으로 개인적 관심 단계(85.18), 운영적 관심 단계(81.88), 지각적 관심 단계(82.15), 강화적 관심 단계(68.80), 협동적 관심 단계(61.97), 그리고 결과적 관심단계(59.76)의 순으로 나타났다. 둘째, 창의 인성 교육에 대한 가정과 교사의 실행 수준은 기계적 실행 수준(수준 3; 21.4%)이 가장 많았으며, 다음으로 탐색 수준(수준 1; 20.9%), 정교화 수준(수준 5; 17.1%), 사용하지 않는 수준(수준 0; 15.0%), 준비 수준(수준 2; 10.2%), 통합 수준(수준 6; 5.9%), 갱신 수준(수준 7; 4.8%), 일상화 수준(수준 4; 4.8%) 순이었다. 셋째, 창의 인성 교육에 대한 가정과 교사의 실행 실태를 조사한 결과, 반 이상의 가정과 교사(56.1%)는 가정과 수업에서 인성 교육에 치중하고 있으며, 31.0%의 교사는 창의 인성 교육을 모두 실행한다고 응답하였다. 반면 소수의 교사(6.4%)는 창의성 교육을 실행한다고 응답하였고 같은 수의 교사(6.4%)는 창의성과 인성 교육 어느 것도 실행하지 않는다고 응답하였다. 가정과 교사의 창의 인성 교육 요소의 실행 정도를 조사한 결과, 창의 인성 교육 요소의 실행은 평균은 5점 만점에서 3.76이었고 창의성 요소의 평균은 3.59, 인성 요소의 평균은 3.94로 보통보다 높았다. 창의성 교육 요소의 실행 정도에 대해서, 개방성/민감성(3.97)을 가장 많이 실행하였고 다음으로 문제해결능력(3.79), 호기심/흥미(3.73), 비판적 사고(3.68), 논리/분석적 사고(3.63), 문제발견능력(3.61), 독창성(3.57), 유추성(3.47), 유창성/융통성(3.46), 정교성(3.46), 상상력(3.37), 몰입/공감(3.37)의 순으로 실행하였다. 인성 교육 요소는 실천력(4.07)을 가장 많이 실행하였고, 다음으로 협동/배려/공정(4.06), 자기관리능력(4.04), 시민의식(4.04), 진로개발능력(4.03), 환경친화능력(3.95), 책임(감)/소유(3.94), 의사결정능력(3.89), 신뢰/정직/약속(3.88), 자율성(3.86), 글로벌역량(3.55)의 순으로 실행한 것으로 나타났다. 창의 인성 교육을 실행할 때 어려운 점으로, 많은 가정과 교사(64.71%)는 창의 인성 교육을 실행할 수업 자료가 부족한 데 있다고 하였으며, 40.11%의 교사는 창의 인성 교육의 연수 기회가 적은데 있다고 응답하였다. 한편 38.50%의 가정과 교사는 창의 인성 교육에 대한 평가 기준을 설정하거나 평가 도구를 개발하는 것이 어렵다고 응답하였고, 25.67%의 교사는 창의 인성 교육 방법을 모른다고 응답하였다. 창의 인성 교육 실행을 위해서 필요한 지원에 대해서, '창의 인성 교육과 관련된 학생들의 체험활동의 확대'(4.34), '창의성과 인성을 중시하는 가정과 수업 문화 조성'(4.29), '학생 발달 단계에 적합한 창의 인성 교육 내용'(4.27), '창의 인성 교육을 담당할 교수 인력 확보'(4.21), '창의 인성 교육의 개념과 가치 확립'(4.09), '지역 사회 기업 등과 연계한 창의 인성 교육 추진'(3.94)의 순으로 응답하였다.

• 대한의용생체공학회:의공학회지
• /
• 제6권2호
• /
• pp.1-8
• /
• 1985

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70$\pm$1.32mmHg/min)compared to CF dialyzers(4.32$\pm$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500, 550, 570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500, 550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100, 300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3, 000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.SpO2 with Plethysmograph.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 1993년도 한국우주과학회보 제2권2호
• /
• pp.17-17
• /
• 1993

The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70${\pm}$1.32mmHg/min)compared to CF dialyzers(4.32${\pm}$0.55mmHg/min)(p<0.05). However, there was no observable difference in the UFR between the two dialyzers. Neither APD nor UFR showed any significant increase with an increasing number of reuses for up to more than 20reuses. A substantial number of failures observed in APD(larger than 20mmHe/min)on the reused dialyzers(2 out of 40 CP and S out 26 C-DAK) were attributed to the Possible damage on the fibers. The CF 15-11 HFDs which failed APD test did not show changes in the UFR compared to normal dialyzers indicating that APD is a more sensitive test than UFR test to evaluate the integrity of the fibers. 30527 T00401030527 ^x For quantitative measurement of reflected light from a clinical diagnostic strip, a prototype old reflectance photometer was designed. The strip loader and cassette were made to obtain more accurate reflectance parameters. The strip was illuminated at 45˚c through optical fiber and the intensity of reflected light was determined at rectanguLat angle using a photodiode. The kubelka-munk coefficient and reflection optical density were determined ar four different wavelengths(500,550,570 and 610nm) for blood glucose strip. For higher concentration than 300mg/41 about glucose, a saturation state of abforbance was observed at 500,550 and 570nm. The correlation between glucose concentration and parameters was the best at 610nm. 30535 T00401030535 ^x Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided into two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weight). The other group received no Photofrin II. Mice from both groups were irradialed for approximately 15 minutes at 100,300, or 500 mW/cm2 with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photolfrin II increased surface temperature by at least 40% and the temperature rise due to 300 mW/cm2 irradiation exceeded values for hyperthermia. Light and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise. 30536 T00401030536 ^x We investigated the structural geometry of thirty-eight Korean femurs. The purpose of this study is to identify major geometrical differences between Korean femurs 3nd others that we believe belong to Caucasians so that we would be able to get insights into the femoral component design that fits Asians including Koreans. We utilized computerized tomography (CT) images of femurs extracted from cadavers. The CT images were transformed into bitmap data by using a film scanner, and then analyzed by using a commercially available software called Image v.1.0 and a Macintosh IIci computer.The resulting data were compared with already published data. The major results show that the geometry of the Korean femurs is significantly different from that of Caucasians: (1) the anteversion angle and the canal flare index are greater by the amount of approximately 8˚ and 0.5, respectively, (2) the shape of the isthmus cross section is more round, and (3) the distance between the teaser trochanter and the proximal border of the isthmus is shelter by about 15 mm. The results suggested that the femoral component suitable for Asians should be different from the currently-used components designed and manufactured mostly by European or American companies. 30537 T00401030537 ^x It is well known that nonlinear propagation characteristics of the wave in the tissue may give very useful information for the medical diagnoisis. In this paper, a new method to detect nonlinear propagation characteristics of the internal vibration in the tissue for the low frequency mechanical vibration by using bispectral analysis is proposed. In the method, low frequency vibration of f0( = 100Hz) is applied on the surface of the object, and the waveform of the internal vibration x (t) is measured from Doppler frequency modulation of silmultaneously transmitted probing ultrasonic waves. Then, the bispectra of the signal x (t) at the frequencies (f0, f0) and (f0, 2f0) are calculated to estimate the nonlinear propagation characteristics as their magnitude ratio, w here since bispectrum is free from the gaussian additive noise we can get the value with high S/N. Basic experimental system is constructed by using 3.0 MHz probing ultrasonic waves and the several experiments are carried out for some phantoms. Results show the superiority of the proposed method to the conventional method using power spectrum and also its usefulness for the tissue characterization. 30541 T00401030541 ^x This paper describes the implementation of a computerized radial pulse diagnosis by aids of a clinical expert. On this base, we composed of the radial pulse diagnosis system in korean traditional medicine. The system composed of a radial pulse wave detection system and a radial pulse diagnosis system. With a detection system, we detected Inyoung and Cheongu radial pulse wave and processed it. Then, we have got the characteristic parameters of radial pulse wave and also quantified that according to the method of Inyoung-Cheongu Comparison Radial Pulse Diagnosis. We defined the jugement standard of radial pulse diagnosis system and then we confirmed the possibility for realization of automatic radial pulse diagnosis in korean traditional medicine. 30545 T00401030545 ^x Microspheres are expected to be applied to biomedical areas such as solid-phase immunoassays, drug delivery systems, immunomagnetic cell separation. To synthesize microspheres for biomedical application, "two stage shot growth method" was developed. The uniformity ratio of synthesized microspheres was always smaller than 1.05. And the surface charge density (or the number of ionizable functional groups) of the microspheres synthesized by "two stage shot growth method" was 6~13 times higher than that of the microspheres synthesized by conventional seeded batch copolymerization. As a previous step for biomedical application, adsorption experiments of bovine albumin on microspheres were carried out under various conditions. The maximum adsorbed amount was obtained in the neighborhood of pH 4.5. Isoelectric point of bovine albumin is pH 5.0, so experimental result shows that it shifted to acid area. The adsorption isotherm was obtained, the plateau region was always reached at 2.Og/L (bulk concentration of bovine albumin).The effect of the kind and the amount of surface functional group was also examined. 30575 T00401030575 ^x A medical image workstation was developed using multimedia technique. The system based on PC-486DX was designed to acquire medical images produced by medical imaging instruments and related audio information, that is, doctors' reporting results. Input information was processed and analyzed, then the results were presented in the form of graph and animation. All the informations of the system were hierarchically related with the image as the apex. Processing and analysis algorithms were implemented so that the diagnostic accuracy could be improved. The diagnosed information can be transferred for patient diagnosis through LAN(local area network). 30592 T00401030592 ^x In the conventional infrared imaging system, complex infrared lens systems are usually used for directing collimated narrow infrared beams into the high speed 2-dimensional optic scanner. In this paper, a simple reflective infrared optic system with a 2-dimensional optic scanner is proposed for the realization of medical infrared thermography system. It has been experimentally proven that the intfrared thermography system composed of the proposed optic system has the temperature resolution of 0.1˚c under the spatial resolution of lmrad, the image matrix size of 256 X 240, and tile imaging time of 4 seconds. 30593 T00401030593 ^x In this paper, MIIS (Medical Image Information System) has been designed and implemented using INGRES RDBMS, which is based on a client/server architecture. The implemented system allows users to register and retrieve patient information, medical images and diagnostic reports. It also provides the function to display these information on workstation windows simultaneously by using the designed menu-driven graphic user interface. The medical image compression/decompression techniques are implemented and integrated into the medical image database system for the efficient data storage and the fast access through the network. 30594 T00401030594 ^x In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality. 30608 T00401030608 ^x Laboratory information system (LIS) is a key tool to manage laboratory data in clinical pathology. Our department has developed an information system for routine hematology using down-sized computer system. We have used an IBM 486 compatible PC with 16MB main memory, 210 MB hard disk drive, 9 RS-232C port and 24 pin dot printer. The operating system and database management system were SCO UNIX and SCO foxbase, respectively. For program development, we used Xbase language provided by SCO foxbase. The C language was used for interface purpose. To make the system use friendly, pull-down menu was used. The system connected to our hospital information system via application program interface (API), so the information related to patient and request details is automatically transmitted to our computer. Our system interfaced with fwd complete blood count analyzers(Sysmex NE-8000 and Coulter STKS) for unidirectional data tansmission from analyzer to computer. The authors suggests that this system based on down-sized computer could provide a progressive approach to total LIS based on local area network, and the implemented system could serve as a model for other hospital's LIS for routine hematology. 30609 T00401030609 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed a composite that is consisted of calcium phosphate and collagen. To use as the structural matrix of the composite, collagen was purified from human umbilical cord. The obtained collagen was treated by pepsin to remove telopeptides, and finally, the immune-free atelocollagen was produced: The cross linked atelocollagen was highly resistant to the collagenase induced collagenolysis. The cross linked collagen demonstrated an improved tensile strength. 30618 T00401030618 ^x This paper is a study on the design of adptive filter for QRS complex detection. We propose a simple adaptive algorithm to increase capability of noise cancelation in QRS complex detection with two stage adaptive filter. At the first stage, background noise is removed and at the next stage, only spectrum of QRS complex components is passed. Two adaptive filters can afford to keep track of the changes of both noise and QRS complex. Each adaptive filter consists of prediction error filter and FIR filter The impulse response of FIR filter uses coefficients of prediction error filter. The detection rates for 105 and 108 of MIT/BIH data base were 99.3% and 97.4% respectively. 30619 T00401030619 ^x To develop an artificial bone substitute that is gradually degraded and replaced by the regenerated natural bone, the authors designed and produced a composite that is consisted of calcium phosphate and collagen. Human umbilical cord origin pepsin treated type I atelocollagen was used as the structural matrix, by which sintered or non-sintered carbonate apatite was encapsulated to form an inorganic-organic composite. With cross linking atelocollagen by UV ray irradiation, the resistance to both compressive and tensile strength was increased. Collagen degradation by the collagenase induced collagenolysis was also decreased. 30620 T00401030620 ^x We have developed a monoleaflet polymer valve as an inexpensive and viable alternative, especially for short-term use in the ventricular assist device or total artificial heart. The frame and leaflet of the polymer valve were made from polyurethane, To evaluate the hemodynamic performance of the polymer valve a comparative study of flow dynamics past a polymer valve and a St. Jude Medical prosthetic valve under physiological pulsatile flow conditions in vitro was made. Comparisons between the valves were made on the transvalvular pressure drop, regurgitation volume and maximum valve opening area. The polymer valve showed smaller regurgitation volume and transvalvular pressure drop compared to the mechanical valve at higher heart rate. The results showed that the functional characteristics of the polymer valve compared favorably with those of the mechanical valve at higher heart rate. 30621 T00401030621 ^x Explosive evaporative removal process of biological tissue by absorption of a CW laser has been simulated by using gelatin and a multimode Nd:YAG laser. Because the point of maximun temperature of laser-irradiated gelatin exists below the surface due to surface cooling, evaporation at the boiling temperature is made explosively from below the surface. The important parameters of this process are the conduction loss to laser power absorption (defined as the conduction-to-laser power parameter, Nk), the convection heat transfer at the surface to conduction loss (defined as Bi), dimensionless extinction coefficient (defined as Br.), and dimensionless irradiation time (defined as Fo). Dependence of Fo on Nk and Bi has been observed by experiment, and the results have been compared with the numerical results obtained by solving a 2-dimensional conduction equation. Fo and explosion depth (from the surface to the point of maximun temperature) are increased when Nk and Bi are increased.To find out the minimum laser power for explosive evaporative removal process, steady state analysis has been also made. The limit of Nk to induce evaporative removal, which is proportional to the inverse of the laser power, has been obtained. 30622 T00401030622 ^x N1 and N2 gross neural action potentials were measured from the round window of the guinea pig cochlea at the onset of the acoustic stimuli. N1-N2 audiograms were made by means of regulating stimulant intensities in order to produce constant N1-N2 potentials as criteria for different input tone pip frequencies. The lowest threshold was measured with an input tone pip I5 dB SPL in intensity and 12 KHz in frequency when the animal was in normal physiological condition. The procedure of experimental measurements is explained in detail. This experimental approach is very useful for the investigation of the Cochlear function. Both noN1inear and active functions of the Cochlea can be monitored by N1-N2 audiograms. 30623 T00401030623 ^x In electrical impedance tomography(EIT), we use boundary current and voltage measurements toprovide the information about the cross-sectional distribution of electrical impedance or resistivity. One of the major problems in EIT has been the inaccessibility of internal voltage or current data in finding the internal impedance values. We propose a new image reconstruction method using internal current density data measured by NMR. We obtained a two-dimensional current density distribution within a phantom by processing the real and imaginary MR images from a 4.77 NMR machine. We implemented a resistivity mage reconstruction algorithm using the finite element method and sensitivity matrix. We presented computer simulation results of the mage reconstruction algorithm and furture direction of the research. 30624 T00401030624 ^x A new method of digital image analysis technique for discrimination of cancer cell was presented in this paper. The object image was the Thyroid eland cells image that was diagnosed as normal and abnormal (two types of abnormal: follicular neoplastic cell, and papillary neoplastic cell), respectively. By using the proposed region segmentation algorithm, the cells were segmented into nucleus. The 16 feature parameters were used to calculate the features of each nucleus. A9 a consequence of using dominant feature parameters method proposed in this paper, discrimination rate of 91.11% was obtained for Thyroid Gland cells. 30625 T00401030625 ^x An electrical stimulator was designed to induce locomotion for paraplegic patients caused by central nervous system injury. Optimal stimulus parameters, which can minimize muscle fatigue and can achieve effective muscle contraction were determined in slow and fast muscles in Sprague-Dawley rats. Stimulus patterns of our stimulator were designed to simulate electromyographic activity monitored during locomotion of normal subjects. Muscle types of the lower extremity were classified according to their mechanical property of contraction, which are slow muscle (msoleus m.) and fast muscle (medial gastrocneminus m., rectus femoris m., vastus lateralis m.). Optimal parameters of electrical stimulation for slow muscles were 20 Hz, 0.2 ms square pulse. For fast muscle, 40 Hz, 0.3 ms square pulse was optimal to produce repeated contraction. Higher stimulus intensity was required when synergistic muscles were stimulated simultaneously than when they were stimulated individually. Electrical stimulation for each muscle was designed to generate bipedal locomotion, so that individual muscles alternate contraction and relaxation to simulate stance and swing phases. Portable electrical stimulator with 16 channels built in microprocessor was constructed and applied to paraplegic patients due to lumbar cord injury. The electrical stimulator restored partially gait function in paraplegic patients. 30626 T00401030626 ^x Two-Dimensional modelling of the Cochlear biomechanics is presented in this paper. The Laplace partial differential equation which represents the fluid mechanics of the Cochlea has been transformed into two-dimensional electrical transmission line. The procedure of this transformation is explained in detail. The comparison between one and two dimensional models is also presented. This electrical modelling of the basilar membrane (BM) is clearly useful for the next approach to the further. Development of active elements which are essential in the producing of the sharp tuning of the BM. This paper shows that two-dimension model is qualitatively better than one-dimensional model both in amplitude and phase responses of the BM displacement. The present model is only for frequency response. However because the model is electrical, the two-dimensional transmission line model can be extended to time response without any difficult. 30627 T00401030627 ^x A method has been proposed for the fully automatic detection of left ventricular endocardial boundary in 2D short axis echocardiogram using geometric model. The procedure has the following three distinct stages. First, the initial center is estimated by the initial center estimation algorithm which is applied to decimated image. Second, the center estimation algorithm is applied to original image and then best-fit elliptic model estimation is processed. Third, best-fit boundary is detected by the cost function which is based on the best-fit elliptic model. The proposed method shows effective result without manual intervention by a human operator. 30628 T00401030628 ^x The intelligent trajectory control method that controls moving direction and average velocity for a prosthetic arm is proposed by pattern recognition and force estimations using EMG signals. Also, we propose the real time trajectory planning method which generates continuous accelleration paths using 3 stage linear filters to minimize the impact to human body induced by arm motions and to reduce the muscle fatigue. We use combination of MLP and fuzzy filter for pattern recognition to estimate the direction of a muscle and Hogan's method for the force estimation. EMG signals are acquired by using a amputation simulator and 2 dimensional joystick motion. The simulation results of proposed prosthetic arm control system using the EMf signals show that the arm is effectively followed the desired trajectory depended on estimated force and direction of muscle movements. 30638 T00401030638 ^x A new neural network architecture for the recognition of patterns from images is proposed, which is partially based on the results of physiological studies. The proposed network is composed of multi-layers and the nerve cells in each layer are connected by spatial filters which approximate receptive fields in optic nerve fields. In the proposed method, patterns recognition for complicated images is carried out using global features as well as local features such as lines and end-points. A new generating method of matched filers representing global features is proposed in this network. 30659 T00401030659 ^x An implementation scheme of the magnetic nerve stimulator using a switching mode power supply is proposed. By using a switching mode power supply rather than a conventional linear power supply for charging high voltage capacitors, the weight and size of the magnetic nerve stimulator can be considerably reduced. Maximum output voltage of the developed magnetic nerve stimulator using the switching mode power supply is 3,000 volts and switching time is about 100 msec. Experimental results or human nerve stimulations using the developed stimulator are presented. 30768 T00401030768 ^x In this paper, we describe the design methodology and specifications of the developed module-based bedside monitors for patient monitoring. The bedside monitor consists of a main unit and module cases with various parameter modules. The main unit includes a 12.1" TFT color LCD, a main CPU board, and peripherals such as a module controller, Ethernet LAN card, video card, rotate/push button controller, etc. The main unit can connect at maximum three module cases each of which can accommodate up to 7 parameter modules. They include the modules for electrocardiograph, respiration, invasive blood pressure, noninvasive blood pressure, temperature, and SpO2 with Plethysmograph.

• 대한교통학회:학술대회논문집
• /
• 대한교통학회 1995년도 제27회 학술발표회
• /
• pp.101-113
• /
• 1995

The objective of this research is to test the feasibility of developing a statewide truck traffic forecasting methodology for Wisconsin by using Origin-Destination surveys, traffic counts, classification counts, and other data that are routinely collected by the Wisconsin Department of Transportation (WisDOT). Development of a feasible model will permit estimation of future truck traffic for every major link in the network. This will provide the basis for improved estimation of future pavement deterioration. Pavement damage rises exponentially as axle weight increases, and trucks are responsible for most of the traffic-induced damage to pavement. Consequently, forecasts of truck traffic are critical to pavement management systems. The pavement Management Decision Supporting System (PMDSS) prepared by WisDOT in May 1990 combines pavement inventory and performance data with a knowledge base consisting of rules for evaluation, problem identification and rehabilitation recommendation. Without a r.easonable truck traffic forecasting methodology, PMDSS is not able to project pavement performance trends in order to make assessment and recommendations in the future years. However, none of WisDOT's existing forecasting methodologies has been designed specifically for predicting truck movements on a statewide highway network. For this research, the Origin-Destination survey data avaiiable from WisDOT, including two stateline areas, one county, and five cities, are analyzed and the zone-to'||'&'||'not;zone truck trip tables are developed. The resulting Origin-Destination Trip Length Frequency (00 TLF) distributions by trip type are applied to the Gravity Model (GM) for comparison with comparable TLFs from the GM. The gravity model is calibrated to obtain friction factor curves for the three trip types, Internal-Internal (I-I), Internal-External (I-E), and External-External (E-E). ~oth "macro-scale" calibration and "micro-scale" calibration are performed. The comparison of the statewide GM TLF with the 00 TLF for the macro-scale calibration does not provide suitable results because the available 00 survey data do not represent an unbiased sample of statewide truck trips. For the "micro-scale" calibration, "partial" GM trip tables that correspond to the 00 survey trip tables are extracted from the full statewide GM trip table. These "partial" GM trip tables are then merged and a partial GM TLF is created. The GM friction factor curves are adjusted until the partial GM TLF matches the 00 TLF. Three friction factor curves, one for each trip type, resulting from the micro-scale calibration produce a reasonable GM truck trip model. A key methodological issue for GM. calibration involves the use of multiple friction factor curves versus a single friction factor curve for each trip type in order to estimate truck trips with reasonable accuracy. A single friction factor curve for each of the three trip types was found to reproduce the 00 TLFs from the calibration data base. Given the very limited trip generation data available for this research, additional refinement of the gravity model using multiple mction factor curves for each trip type was not warranted. In the traditional urban transportation planning studies, the zonal trip productions and attractions and region-wide OD TLFs are available. However, for this research, the information available for the development .of the GM model is limited to Ground Counts (GC) and a limited set ofOD TLFs. The GM is calibrated using the limited OD data, but the OD data are not adequate to obtain good estimates of truck trip productions and attractions .. Consequently, zonal productions and attractions are estimated using zonal population as a first approximation. Then, Selected Link based (SELINK) analyses are used to adjust the productions and attractions and possibly recalibrate the GM. The SELINK adjustment process involves identifying the origins and destinations of all truck trips that are assigned to a specified "selected link" as the result of a standard traffic assignment. A link adjustment factor is computed as the ratio of the actual volume for the link (ground count) to the total assigned volume. This link adjustment factor is then applied to all of the origin and destination zones of the trips using that "selected link". Selected link based analyses are conducted by using both 16 selected links and 32 selected links. The result of SELINK analysis by u~ing 32 selected links provides the least %RMSE in the screenline volume analysis. In addition, the stability of the GM truck estimating model is preserved by using 32 selected links with three SELINK adjustments, that is, the GM remains calibrated despite substantial changes in the input productions and attractions. The coverage of zones provided by 32 selected links is satisfactory. Increasing the number of repetitions beyond four is not reasonable because the stability of GM model in reproducing the OD TLF reaches its limits. The total volume of truck traffic captured by 32 selected links is 107% of total trip productions. But more importantly, ~ELINK adjustment factors for all of the zones can be computed. Evaluation of the travel demand model resulting from the SELINK adjustments is conducted by using screenline volume analysis, functional class and route specific volume analysis, area specific volume analysis, production and attraction analysis, and Vehicle Miles of Travel (VMT) analysis. Screenline volume analysis by using four screenlines with 28 check points are used for evaluation of the adequacy of the overall model. The total trucks crossing the screenlines are compared to the ground count totals. L V/GC ratios of 0.958 by using 32 selected links and 1.001 by using 16 selected links are obtained. The %RM:SE for the four screenlines is inversely proportional to the average ground count totals by screenline .. The magnitude of %RM:SE for the four screenlines resulting from the fourth and last GM run by using 32 and 16 selected links is 22% and 31 % respectively. These results are similar to the overall %RMSE achieved for the 32 and 16 selected links themselves of 19% and 33% respectively. This implies that the SELINICanalysis results are reasonable for all sections of the state.Functional class and route specific volume analysis is possible by using the available 154 classification count check points. The truck traffic crossing the Interstate highways (ISH) with 37 check points, the US highways (USH) with 50 check points, and the State highways (STH) with 67 check points is compared to the actual ground count totals. The magnitude of the overall link volume to ground count ratio by route does not provide any specific pattern of over or underestimate. However, the %R11SE for the ISH shows the least value while that for the STH shows the largest value. This pattern is consistent with the screenline analysis and the overall relationship between %RMSE and ground count volume groups. Area specific volume analysis provides another broad statewide measure of the performance of the overall model. The truck traffic in the North area with 26 check points, the West area with 36 check points, the East area with 29 check points, and the South area with 64 check points are compared to the actual ground count totals. The four areas show similar results. No specific patterns in the L V/GC ratio by area are found. In addition, the %RMSE is computed for each of the four areas. The %RMSEs for the North, West, East, and South areas are 92%, 49%, 27%, and 35% respectively, whereas, the average ground counts are 481, 1383, 1532, and 3154 respectively. As for the screenline and volume range analyses, the %RMSE is inversely related to average link volume. 'The SELINK adjustments of productions and attractions resulted in a very substantial reduction in the total in-state zonal productions and attractions. The initial in-state zonal trip generation model can now be revised with a new trip production's trip rate (total adjusted productions/total population) and a new trip attraction's trip rate. Revised zonal production and attraction adjustment factors can then be developed that only reflect the impact of the SELINK adjustments that cause mcreases or , decreases from the revised zonal estimate of productions and attractions. Analysis of the revised production adjustment factors is conducted by plotting the factors on the state map. The east area of the state including the counties of Brown, Outagamie, Shawano, Wmnebago, Fond du Lac, Marathon shows comparatively large values of the revised adjustment factors. Overall, both small and large values of the revised adjustment factors are scattered around Wisconsin. This suggests that more independent variables beyond just 226; population are needed for the development of the heavy truck trip generation model. More independent variables including zonal employment data (office employees and manufacturing employees) by industry type, zonal private trucks 226; owned and zonal income data which are not available currently should be considered. A plot of frequency distribution of the in-state zones as a function of the revised production and attraction adjustment factors shows the overall " adjustment resulting from the SELINK analysis process. Overall, the revised SELINK adjustments show that the productions for many zones are reduced by, a factor of 0.5 to 0.8 while the productions for ~ relatively few zones are increased by factors from 1.1 to 4 with most of the factors in the 3.0 range. No obvious explanation for the frequency distribution could be found. The revised SELINK adjustments overall appear to be reasonable. The heavy truck VMT analysis is conducted by comparing the 1990 heavy truck VMT that is forecasted by the GM truck forecasting model, 2.975 billions, with the WisDOT computed data. This gives an estimate that is 18.3% less than the WisDOT computation of 3.642 billions of VMT. The WisDOT estimates are based on the sampling the link volumes for USH, 8TH, and CTH. This implies potential error in sampling the average link volume. The WisDOT estimate of heavy truck VMT cannot be tabulated by the three trip types, I-I, I-E ('||'&'||'pound;-I), and E-E. In contrast, the GM forecasting model shows that the proportion ofE-E VMT out of total VMT is 21.24%. In addition, tabulation of heavy truck VMT by route functional class shows that the proportion of truck traffic traversing the freeways and expressways is 76.5%. Only 14.1% of total freeway truck traffic is I-I trips, while 80% of total collector truck traffic is I-I trips. This implies that freeways are traversed mainly by I-E and E-E truck traffic while collectors are used mainly by I-I truck traffic. Other tabulations such as average heavy truck speed by trip type, average travel distance by trip type and the VMT distribution by trip type, route functional class and travel speed are useful information for highway planners to understand the characteristics of statewide heavy truck trip patternS. Heavy truck volumes for the target year 2010 are forecasted by using the GM truck forecasting model. Four scenarios are used. Fo~ better forecasting, ground count- based segment adjustment factors are developed and applied. ISH 90 '||'&'||' 94 and USH 41 are used as example routes. The forecasting results by using the ground count-based segment adjustment factors are satisfactory for long range planning purposes, but additional ground counts would be useful for USH 41. Sensitivity analysis provides estimates of the impacts of the alternative growth rates including information about changes in the trip types using key routes. The network'||'&'||'not;based GMcan easily model scenarios with different rates of growth in rural versus . . urban areas, small versus large cities, and in-state zones versus external stations. cities, and in-state zones versus external stations.

• 한국작물학회지
• /
• 제17권
• /
• pp.1-44
• /
• 1974

본연구는 1972년에 수원에서 그리고 1973년에는 다시 수원, 매리 및 이리 광주의 3개 지역에서 경질 소맥인 NB 68513, Caprock와 중간질 소맥인 영광, 연질 소맥인 수계 169호를 공시하여 시비량 및 재배시기를 각각 3수준의 처리를 두어 등숙 및 품질의 변화에 관한 실험을 수행하였다. 한편 1973년 및 1974년에는 수원에서 중간질 소맥인 영광과 경질 소맥인 NB 68513을 공시하고 온실에서 온도, 습도 및 일사량을 달리하여 이들이 소맥의 등숙과 품질에 미치는 영향을 추구하였으며, 얻어진 결과는 다음과 같다. 1. 소맥립의 등숙: 1) 1립중의 변이폭은 대립종이 소립종에 비하여 크고, 립중별 소맥립의 분포는 대립종이 평균치에 가까이 분포된 율이 높았고, 소립종은 넓은 분산을 보였다. 2) 립중의 증가에 미치는 립장, 립후 및 립폭의 영향의 정도는 립장보다 립후와 립폭이 컸다. 3) 등숙 시기별 립중의 변화에 있어서 영광은 개화후 14일부터 35일까지, NB 68513은 14일부터 28일까지에 급증하였고, 대립종인 영광은 소립종인 NB68513에 비하여 등숙기간이 길었으며 배란비율도 완만한 증가를 보였다. 4) 1000립중은 대체로 저온에서보다 고온에서, 다습보다 건조한 공중습도 조건에서 가벼웠고, 저온이나 고온에서라도 다습 조건하에서는 무거운 경향을 보였다. 또한 서광의 영향은 저온에서보다 고온에서 컸으며, 다습한 경우에는 일정한 경향이 없었다. 5) 등숙기간중 온도, 습도 및 서광의 영향은 소립종인 NB 68513보다 대립종인 영광에서 컸으며, 1000립중의 증감과 등숙일수 간에는 높은 정의 상관이 있었다. 6) 1000립중과 1$\ell$중은 시비량의 증가에 따라 무거워졌으나, 보비와 다비구간에는 그 증가율이 비교적 낮았고, 조숙재배는 만파재배보다 무거웠으며, 이와 같은 경향은 수원에서 현저하였고 광주 및 이리에서는 미미하였다. 2. 제분성: 7) 동일 품종에서 1000립중이 무겁게 나타난 저온다습 조건 및 조숙재배가 고온, 건조, 조건 및 만파재배에 비하여 제분율이 높았고, 지역간 차이는 일정한 경향이 없었다. 8) 제분율은 영광이 가장 높고 수계 169호가 가장 낮았으며, 경질 소립종인 Caprock, NB 68513은 연질 소립종인 수계 169호보다 높았다. 9) 회분 함량은 지역, 시비량 및 재배시기에 따른 차이는 작았고, 품종간 차이는 컸으며, NB 68513 및 Caprock는 영광 및 수계 169호보다 현저히 높았다. 3. 단백질 함량: 10) 단백질 함량은 1000립중이 가벼웠든 고온, 건조 및 서광 조건에서 저온, 다습 조건에서보다 높았으며, 이러한 경향은 영광에서 현저하고 NB 68513에서 적었다. 11) 종질의 단백질 함량은 개화후 1~2주일 사이에 높았는데, 이는 배란에 대한 배와 종피의 비율이 크기 때문이었고, 등숙이 진전됨에 따라 배, 종피의 영향은 감소되며, 달서 단백질 함량도 감소되었으나 개화후 3~4주부터는 다시 단백질함량이 증가되어 개화후 7주에 최대에 달하였다. 등숙 중기(개화후 3~4주) 이후의 단백질함량 증가는 대체로 1000립중의 증가와 비슷하였으나, 성숙된 종실의 단백질 함량의 증감은 등숙기간의 장단의 영향보다는 역일상에 따른 기상적 환경, 특히 기온에 의한 영향을 많이 받은 것으로 보였다. 12) 소맥분의 단백질 함량은 종실의 단백질 함량의 변화와 같아서 이 양자간에는 높은 정의 상관이 있었다. 13) 단백질 함량은 각 품종 모두 시비량이 증가할수록, 또 재배시기가 늦어질수록 증가하는 경향이었고, 수원에서는 광주, 이리에서보다 그 경향이 현저하였다. 14) 품종별로 존 단백질 함량은 영광, NB 68513 및 Caprock은 비슷하였으며 비교적 높았고, 수계 169호는 낮았는데 이 품종은 재배법에 따른 단백질 함량의 변이도 적었다. 15) 단위 면적당 단백질 수량은 시비량이 많을수록, 재배시기가 빠를수록 높은 경향이었고, 조숙재배에서는 질소질 비료의 이용율이 높았으며, 영광은 시비량 증가에 따른 단백질 수량 증가가 비교적 컸다. 4. 분의 물리화학적 특성: 16) Sedimentation value는 저온, 다습, 소비 조건에서보다 고온, 건조, 다비 조건에서 컸고, NB 68513 및 Caprock는 그 경향이 현저하였는데 영광 및 수계 169호는 뚜렷하지 않았었고, 광주, 이리보다는 수원에서 Sedimentation value의 변이가 컸다. Sedimentation value의 증감은 단백질 함량의 증감과 관계가 깊으나, 다습조건에서는 Sedimentation value가 감소되었다. 한편 Sedimentation value는 단백질 함량의 증가에 따라 증가되었으며, 성숙기에 최대에 달하였다. 17) Pelshenke value는 재배방법 및 지역 간의 차이가 Sedimentation value의 경우와 대체로 같은 경향을 보였다. 18) Mixing time은 NB 68513이 4~6분, Caprock가 5~7분 소요되었으며, 영광 및 수계 169호는 NB 68513 및 Caprock보다 지역 및 재배법에 따른 변이가 컸다. Mixing height와 Mixing area는 NB 68513 및 Caprock에서 컸고 영광 및 수계 169호에서는 작았으며, 재배방법에 따른 변이는 일정한 경향이 없었고, 지역에 따른 차이는 이리, 광주에서 낮고 수원에서 높았다. 19) NB 68513 및 Caprock의 품질에 있어서 제분성은 고온, 건조 조건, 또는 다비, 만파재배에서 떨어졌으나 분의 물리화학적 특성은 양호하여 제빵 적성이 좋고, 조숙재배는 물리화학적 특성이 다소 불량하였으나 제분성이 높고 단위 면적당 단백질 수량인 높은 경향이었다. 지역간에서 보면 이리, 광주보다는 수원이 NB 68513 및 Caprock의 재배에 적합한 것으로 판단되었다. 5. 분의 물리화학적 특성의 상호관계: 20) 제분율 및 회분함량과 분의 물리화학적 특성과는 직접적인 상관이 없었으며, 1000립중이 가벼운 것이 단백질 함량이 높았고 분의 물리화학적 특성도 양호하였다. 21) NB 68513 및 Caprock에 있어서 단백질 함량과 Sedimentation value, Pelshenke value 및 mixing height와는 정의 상관이 있었으며, 단백질 함량이 높으면 분의 Gluten strength도 강하고 따라서 제빵 적성도 양호하였다. 영광 및 수계 169호에 있어서는 단백질 함량과 Sedimentation value와는 정의 상관이 있으나 Pelshenke value와 Mixing height와는 상관이 없었다. 따라서 단백질 함량 증가에 따라 Gluten strength 양자와 연결됨이 크고, Pelshenke value와 Mixogram은 Gluten strength와 연관됨으로 경질과 연질의 품종 구분에는 Mixogram, Pelshenke value의 검정이 유리하고, Sedimentation valuer검정은 같은 품종내에서 재배법 차이에 따른 품질 평가에 알맞은 것으로 보았다.