• Journal of Satellite, Information and Communications
• /
• v.9 no.2
• /
• pp.74-79
• /
• 2014

Conventional ScanSAR mode has been adopted in Envisat or Radarsat and played an important role to acquire wide swath SAR images for environmental surveillance. However, it suffers from the undesirable scalloping effect caused by non-homogeneity of antenna pattern while the image resolution is sacrificed. In recent years, TOPS mode has been suggested and put into use to overcome the disadvantages of the conventional scanning mode. Although TOPS mode is able to produce wide-swath SAR image in a short time interval, it demands highly complicated system design knowledge. In this paper, we present the operation principle of TOPS mode and a full SAR simulation is performed to generate TOPS SAR raw data. Azimuth antenna pattern is modified during TOPS mode operation and it is shown that the undesired scalloping effect is suppressed in the generated SAR image.

• Korean Journal of Geomatics
• /
• v.2 no.1
• /
• pp.37-46
• /
• 2002

Accurate classification of water area is an preliminary step to accurately analyze the flooded area and damages caused by flood. This step is especially useful for monitoring the region where annually repeating flood is a problem. The accurate estimation of flooded area can ultimately be utilized as a primary source of information for the policy decision. Although SAR (Synthetic Aperture Radar) imagery with its own energy source is sensitive to the water area, its shadow effect similar to the reflectance signature of the water area should be carefully checked before accurate classification. Especially when we want to identify small flood area with mountainous environment, the step for removing shadow effect turns out to be essential in order to accurately classify the water area from the SAR imagery. In this paper, the flood area was classified and monitored using multi-temporal RADARSAT SAR images of Ok-Chun and Bo-Eun located in Chung-Book Province taken in 12th (during the flood) and 19th (after the flood) of August, 1998. We applied several steps of geometric and radiometric calculations to the SAR imagery. First we reduced the speckle noise of two SAR images and then calculated the radar backscattering coefficient $(\sigma^0)$. After that we performed the ortho-rectification via satellite orbit modeling developed in this study using the ephemeris information of the satellite images and ground control points. We also corrected radiometric distortion caused by the terrain relief. Finally, the water area was identified from two images and the flood area is calculated accordingly. The identified flood area is analyzed by overlapping with the existing land use map.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.1
• /
• pp.41-50
• /
• 2008

Recent progress in state-of-the-art geospatial information technologies such as digital mapping, LiDAR(Light Detection And Ranging), and high-resolution satellite imagery provides various data sources fer Digital Elevation Model(DEM). DEMs are major source to extract elements of the hydrological terrain property that are necessary for efficient watershed management. Especially, watersheds extracted from DEM are important geospatial database to identify physical boundaries that are utilized in water resource management plan including water environmental survey, pollutant investigation, polluted/wasteload/pollution load allocation estimation, and water quality modeling. Most of the previous studies related with watershed extraction using DEM are mainly focused on the hydrological elements analysis and preprocessing without considering grid size of the DEMs. This study aims to analyze accuracy of the watersheds extracted from DEMs with various grid sizes generated by LiDAR data and digital map, and appropriate preprocessing methods.

• Geomechanics and Engineering
• /
• v.13 no.6
• /
• pp.1011-1025
• /
• 2017

The geological conditions surrounding the Jijiapo Tunnel of the Three Gorges Fanba Highway project in Hubei Province are very complex. In this paper, a 3-D physical model was carried out to study the evolution process of filling-type fracture water inrush and mud gush based on the conditions of the section located between 16.040 km and 16.042 km of the Jijiapo Tunnel. The 3-D physical model was conducted to clarify the effect of the self-weight of the groundwater level and tunnel excavation during water inrush and mud gush. The results of the displacement, stress and seepage pressure of fracture and surrounding rock in the physical model were analyzed. In the physical model the results of the model test show that the rock displacement suddenly jumped after sustainable growth, rock stress and rock seepage suddenly decreased after continuous growth before water inrushing. Once water inrush occured, internal displacement of filler increased successively from bottom up, stress and seepage pressure of filler droped successively from bottom up, which presented as water inrush and mud gush of filling-type fracture was a evolving process from bottom up. The numerical study was compared with the model test to demonstrate the effectiveness and accuracy of the results of the model test.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2016.05a
• /
• pp.195-195
• /
• 2016

Kon - Ha Thanh River basin is the largest and the most important river basin in Binh Dinh, a province in the South Central Coast of Vietnam. In the lower rivers, frequent flooding and inundation caused by heavy rains, upstream flood and or uncontrolled flood released from upstream reservoirs, are very serious, causing damage to agriculture, socio-economic activity, human livelihood, property and lives. The damage is expected to increase in the future as a result of climate change. An advanced flood warning system could provide achievable non-structural measures for reducing such damages. In this study, we applied a modelling system which intergrates a 1-D river flow model and a 2-D surface flow model for simulating hydrodynamic flows in the river system and floodplain inundation. In the model, exchange of flows between the river and surface floodplain is calculated through established links, which determine the overflow from river nodes to surface grids or vice versa. These occur due to overtopping or failure of the levee when water height surpasses levee height. A GIS based comprehensive raster database of different spatial data layers was prepared and used in the model that incorporated detailed information about urban terrain features like embankments, roads, bridges, culverts, etc. in the simulation. The model calibration and validation were made using observed data in some gauging stations and flood extents in the floodplain. This research serves as an example how advanced modelling combined with GIS data can be used to support the development of efficient strategies for flood emergency and evacuation but also for designing flood mitigation measures.

• Korean Journal of Remote Sensing
• /
• v.37 no.5_3
• /
• pp.1461-1473
• /
• 2021

The purpose of this study is to ascertain how the level of resolution of land cover data affects on the local distribution and diffusion of fine dust. the CALPUFF model, which considers the spatio-temporal terrain conditions and changes in weather conditions, was used to estimate PM10 concentration in the Pyeongchon, Anyang-si, Gyeonggi-do. Three different resolutions of land cover data including 20 m, 50 m, and 100 m were compared as the input of the modeling. Using higher resolution land cover data (20 m), the wind speed of the simulated region was the largest and the PM10 concentration was the lowest. Through this study, we confirm that the resolution level of land-use/cover data can affect the local distribution and diffusion of fine dust, which can be detected by CALPUFF. Therefore, when using CALPUFF to simulate fine dust in the future, it can be suggested that checking the impact on spatial resolution according to the form of land cover in advance and proceeding with the simulation can achieve mote accurate results.

• The Journal of Engineering Geology
• /
• v.31 no.3
• /
• pp.283-293
• /
• 2021

The homogeneity of the compacted ground was analyzed using drone-based remote terrain and gravity field data. Among the topographic elements calculated by the hydrological algorithm, the topographic curvature effectively showed the shape of the surface that occurred during the compaction process, and the non-uniformly compacted area could be identified. The appropriate resolution of the digital topography requires a precision of about 10 cm. Gravity field Interpretation was performed to analyze the spatial density change of the compacted ground. In the distribution of residual bouguer gravity anomaly, the non-homogeneously compacted area showed a different magnitude of gravity than the surrounding area, and the difference in compaction was identified through gravity-density modeling. From the results, it is expected that the topographic element and gravitational field analysis method can be used to evaluate the homogeneity of the compacted ground.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.5
• /
• pp.343-349
• /
• 2021

In The process from design to construction in the existing construction work was less efficient due to the contradictory approach of identifying the 3D state in the plan view and the repeated generation of surveys, floor plans, drawings. Accurate 3D design data is essential for smart construction. However, most of the existing related studies have focused on explaining the development method and main functions of equipment or improving the productivity of smart construction. Therefore, in this study, the utility of 3D design model generation for smart construction and construction survey using 3D laser scanner was evaluated. Plane and vertical road alignment were created using the specifications of the road. The generated road alignment was created as a three-dimensional corridor design using cross-sections at intervals of 20m. In addition, it was possible to create a DTM (Digital Terrain Model) using a digital map and effectively create a 3D design model for the study area through overlapping. Construction survey using a 3D laser scanner showed accuracy within 10cm as a result of the accuracy evaluation. These results proved that construction surveying using a 3D laser scanner is possible because it satisfies the acceptable accuracy of the relevant regulations modeling of target areas using 3D design and construction survey using 3D laser scanner can be a way to address shortcomings of existing GNSS (Global Navigation Satellite System) methods. And accurate 3D data will be used as essential data as basic data for smart construction.

• Atmosphere
• /
• v.31 no.2
• /
• pp.185-198
• /
• 2021

In this study, we examined a spatial downscaling method based on Gradient and Inverse Distance Squared (GIDS) weighting to produce high-resolution grid data from a numerical weather prediction model over Korean Peninsula with complex terrain. The GIDS is a simple and effective geostatistical downscaling method using horizontal distance gradients and an elevation. The predicted meteorological variables (e.g., temperature and 3-hr accumulated rainfall amount) from the Limited-area ENsemble prediction System (LENS; horizontal grid spacing of 3 km) are used for the GIDS to produce a higher horizontal resolution (1.5 km) data set. The obtained results were compared to those from the bilinear interpolation. The GIDS effectively produced high-resolution gridded data for temperature with the continuous spatial distribution and high dependence on topography. The results showed a better agreement with the observation by increasing a searching radius from 10 to 30 km. However, the GIDS showed relatively lower performance for the precipitation variable. Although the GIDS has a significant efficiency in producing a higher resolution gridded temperature data, it requires further study to be applied for rainfall events.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.17 no.1
• /
• pp.33-40
• /
• 2022

With the recent increase in the development of military drones, they are adopted and used as the combat system of battalion level or higher. However, it is difficult to use drones that can be used in battles below the platoon level due to the current conditions for the formation of units in the Korean military. In this paper, therefore, we developed a program drones equipped with a thermal imaging camera and LiDAR sensor for reconnaissance and exploration that can be applied in battles below the platoon level. Using these drones, we studied the possibility and feasibility of drones for small-scale combats that can find hidden enemies, search for an appropriate detour through image processing and conduct reconnaissance and search for battlefields, hiding and cover-up through image processing. In addition to the purpose of using the proposed drone to search for an enemies lying in ambush in the battlefield, it can be used as a function to check the optimal movement path when a combat unit is moving, or as a function to check the optimal place for cover-up or hiding. In particular, it is possible to check another route other than the route recommended by the program because the features of the terrain can be checked from various viewpoints through 3D modeling. We verified the possiblity of flying by designing and assembling in a form of adding LiDAR and thermal imaging camera module to a drone assembled based on racing drone parts, which are open source hardware, and developed autonomous flight and search functions which can be used even by non-professional drone operators based on open source software, and then installed them to verify their feasibility.