• Journal of the Korea Concrete Institute
• /
• v.27 no.2
• /
• pp.185-193
• /
• 2015

Ultra high performance concrete (UHPC) has been developed to overcome the low tensile strengths and brittleness of conventional concrete. Considering that UHPC, owing to its composition and the use of steel fibers, develops a compressive strength of 180 MPa as well as high stiffness, the top flange of the steel girder may be superfluous in the composite beam combining a slab made of UHPC and the steel girder. In such composite beam, the steel girder takes the form of an inverted-T shaped structure without top flange in which the studs needed for the composition of the steel girder with the UHPC slab are disposed in the web of the steel girder. This study investigates experimentally and analytically the flexural behavior of this new type of composite beam to propose details like stud spacing and slab thickness for further design recommendations. To that goal, eight composite beams with varying stud spacing and slab thickness were fabricated and tested. The test results indicated that stud spacing running from 100 mm to 2 to 3 times the slab thickness can be recommended. In view of the relative characteristic slip limit of Eurocode-4, the results showed that the composite beam developed ductile behavior. Moreover, except for the members with thin slab and large stud spacing, most of the specimens exhibited results different to those predicted by AASHTO LRFD and Eurocode-4 because of the high performance developed by UHPC.

• Restorative Dentistry and Endodontics
• /
• v.18 no.1
• /
• pp.73-83
• /
• 1993

The purpose of this study was to evaluate the effect of various acid treatments on dentin bonding. Freshly extracted human teeth were uprightly embedded in self curing acrylic resin, and their occlusal surfaces were grinded to expose flat dentin surfaces. The specimens were divided into 4 groups. Specimens of one group were not treated so as to be a control and those of the other three groups were threated with 10% polyacrylic acid, 10% phosphoric acid, and 10-3 solution(10% citric acid/3% ferric chloride) respectively. Primer, bonding resin and composite resin were applied over the treated dentin surfaces sequentially. All specimens were stored in $37^{\circ}C$ distilled water for 24 hours, then the tensile bond strength was measured and the treated dentin surfaces and fracured dentin surfaces were examined under a scanning electron microscope. The results were as follows: Bond strengths of acid-treated groups were higher than those of the untreated group. In the acid-treated groups, bond strength was found to be the highest in the 10-3 solution group followed by the 10% phosphoric acid group and the 10% polyacrylic acid group(P<0.01). On SEM examination of dentin surfaces, the untreated dentin surface showed a remaining smear layer and closed dentinal tubules. Dentin surfaces treated with 10 % polyacrylic acid showed a clean dentin surface without the smear layer, but showed remaining smear plugs in dentinal tubules. A dentin surface treated with 10% phosphoric acid or 10-3 solution showed open dentinal tubules without the smear layer or smear plugs. On SEM observation of the fractured dentin-resin interface, the untreated group showed that failure occurred in the smear layer. The group treated with 10% polyacrylic acid showed no resin tag remained in the dentinal tubules, but resin tags in the dentinal tubules were observed in the group treated with the 10% phosphoric acid or the 10-3 solution. On the failure mode examination, the higher the bond strength of the group, the higher the frequency of cohesive failure. The coefficient between bond strength and cohesive failure rate was 0.71.

• Journal of Conservation Science
• /
• v.34 no.6
• /
• pp.595-604
• /
• 2018

In this study, in a bid to develop natural bioadhesives for paper craft, the hanji industry, and preserving cultural assets, complex polysaccharides were extracted from brown and red algae and used as an ingredient in adhesives. Brown algae include sea trumpet, kelp, sea oak, and sea mustard, whereas red algae include Pachymeniopsis elliptica agar-agar weed, Gloiopeltis tenax, and hunori. The polysaccharides were extracted after transforming them from non-aqueous Ca complexes contained in each of the brown and red algae into water-soluble polysaccharides containing alkali metals with a solubility level of 1. and extracted Subsequently, only the polysaccharides were extracted using alcohol precipitation. The adhesion tensile strengths of kelp, a brown algae, and Pachymeniopsis elliptica, a red algae, were 21.58 and 32.99 kgf, respectively. They thus demonstrated better adhesion than that of solid glue products such as water plants (18.45 kgf) and glue sticks (20.45 kgf). The extraction yield of these polysaccharides is supposed to be determined according to their extracted environments; however, no difference in adhesion strength was seen. Further, it was found that the shapes of polysaccharides were determined by their growing environment instead of extraction environment. Use of multi-step alcohol precipitation method during extraction enabled the removal of the constituents except protein and other polysaccharides, thereby demonstrating a stable outcome without cultivation of mold. Furthermore, there was no occurrence of mold even after production of the adhesives by the simple solution method, which demonstrates the adhesive's potential as an environment-friendly adhesive material.