• 한국방재학회 논문집
• /
• 제11권2호
• /
• pp.67-73
• /
• 2011

본 연구의 목적은 공기 단축과 초기 공사비를 절감하기 위해 PC 긴장재를 사용하지 않고, 슬리브와 일반 철근만으로 구성된 경제적이면서 시공성이 우수한 프리캐스트 교각 공법 개발에 있다. 이를 위해 본 연구에서는 신형식 철근이음 장치인 그라우팅형(形) 슬리브(Splice sleeve, 이하 슬리브)를 제안하고 최적의 슬리브를 개발하기 위하여 슬리브 길이, 철근직경, 양생방법 등을 변수로 하여 유한요소해석 및 인장실험을 수행하였다. 슬리브의 유한요소해석을 통하여 최적의 형상을 도출하였으며, 인장 성능 검토 결과, 철근의 인발에 의한 파괴는 발생하지 않았으며, 철근의 인장 파괴 혹은 슬리브의 기계적 결함에 의한 볼트 파단만이 관찰되었다. 제안된 슬리브는 우수한 인장성능을 갖고 있음을 확인하였으며 프리캐스트 교각에 무리 없이 적용할 수 있음을 검증하였다.

• 복합신소재구조학회 논문집
• /
• 제5권4호
• /
• pp.24-35
• /
• 2014

An experimental study on the structural behavior of connection types between approach slab and integral abutment has been done for three typical bar connections. Typical hinge style reinforcing bar detail for its connection is preferred in order to accommodate rotation of the approach slab among engineers. However, the straight horizontal bars can be used as connection detail accomodate structural capacity. Total six specimens with three types of rebar detail are tested for direct tensile and bending load. The characteristic structural behaviors are carefully monitored and all the strain gauge data obtained are analyzed. It is shown that the structural performance of all the specimens well exceed its design allowance. Several design suggestions are given based on careful reviews on the experiment.

• 한국지반환경공학회 논문집
• /
• 제13권2호
• /
• pp.83-93
• /
• 2012

보강토옹벽은 1980년대 초반 국내에 도입된 이래로, 다양한 금속 혹은 토목섬유 보강재가 개발되어 현장에 적용되고 있으며, 특히, 국내에서는 지오그리드가 가장 많이 적용되고 있다. 이에 본 연구에서는 현재 국내에서 생산되고 있는 4가지 종류의 지오그리드에 대해 인장강도-인장변형 관계 특성을 고찰하였다. 또한 재질 및 제조방식이 상이한 3가지 지오그리드에 대해서는 일련의 광폭인장강도시험을 수행하여 실제 지오그리드 인장변형과 변형률계에 의해 측정된 인장변형을 비교하였다. 실험결과, 변형률계에 의해 측정된 인장변형률이 광폭인장강도시험기에 의해 측정된 실제변형률 보다 다소 큰 경향을 보이나 인장변형률이 3% 보다 작은 경우에는 측정방법에 따른 차이가 거의 없는 것으로 확인되었다.

• 콘크리트학회논문집
• /
• 제16권4호
• /
• pp.451-458
• /
• 2004

본 연구는 재래 철근과 Fiber Reinforced Polymer 보강재를 사용한 Hybrid Reinforcement System의 기본 개념과 적용성에 대해 기술하고 있다. 콘크리트 교량상관은 보로서 지지되고 상하 두층의 보강재로 인장보강되어 있다. HRS를 이용한 콘크리트 교량상판에서는 보 지지점 부근의 부모멘트에 대한 상부 인장력은 FRP 봉으로 저항하고 보 지지점 중앙부근의 하부인장력은 재래의 철근으로 저항한다. HRS를 이용한 콘크리트 교량상판은 FRP 봉은 비 부식성이고, 부식되기 쉬운 철근은 교량상판 위로부터 가급적 멀리하여 부식물질의 침투를 막을 수 있는 장점이 있다. HRS를 이용한 콘크리트 교량상판은 또한 극한상태에서 충분한 연성을 가지고 있다. 그 이유는 1) FRP봉은 철근보다 탄성계수가 낮고 파단시의 최대 변형률이 크며, 2) 충분한 FRP 보강량을 사용하면 극한변형률을 낮출 수 있으며, 3) 부모멘트 구간의 일부를 비부착시켜 극한 변형률을 낮출 수 있다. 실험 연구 결과 보통의 FRP보강비의 범위에서는 FRP 및 HRS 콘크리트 슬래브는 FRP봉의 파단이 아니라 콘크리트의 압축에 의해 파피됨을 보여주고 있다. 그러므로 HRS를 이용한 연속 콘크리트 교량상관에서는 정모멘트부의 하부철근이 먼저 항복하여 소성힌지를 형성하고 나중에 부보멘트나 정모멘트부의 콘크리트가 압축파괴되어 FRP 콘크리트 슬래브에 비하여 상당한 소성에너지를 소모한다.

• Structural Engineering and Mechanics
• /
• 제47권6호
• /
• pp.819-838
• /
• 2013

This paper summarises the results of an experimental study to investigate the flexural behaviour of reinforced concrete beams strengthened using carbon-fibre reinforced polymer (CFRP) laminate in four-point bending. The experimental parameters included are the reinforcing bar ratio ${\rho}_s$ and preload level. Four bar ratios were selected (${\rho}_s=0.13$ to 0.86%), representing the section of two longitudinal tensile reinforcements, with diameters of 8, 14, 16, and 20 mm in order to reveal the effect of bar ratio on failure load and failure mode. Eight beams that could be considered "full-scale" in size, measuring 200 mm in width, 400 mm in total height and 2300 mm in length, were tested. Three beams were selected with different bar ratios (${\rho}_1$, ${\rho}_2$, ${\rho}_3$), and considered as control specimens (without ), while three other beams identical to the control beams with the same CFRP laminates ratio and a seventh beam with ${\rho}_{min}$ (the lowest bar ratio) were also used. In the second part of the study, two beams with the bar ratio ${\rho}_2$ were preloaded at two levels, 50 and 100% of their ultimate loads, and then repaired. This experimental investigation was consolidated using an analytical model. The experimental and analytical results indicate that the flexional capacity and stiffness of strengthened and repaired beams using CFRP laminate were increased compared to those of control beams, and the behaviour of repaired beams was nearly similar to the undamaged and strengthened beams; unlike the ductility of strengthened beams, which was greatly reduced compared to the control.

• 한국수소및신에너지학회논문집
• /
• 제29권6호
• /
• pp.570-577
• /
• 2018

Composite pressure vessels made through filament winding are widely used in various fields. Numerous studies regarding composite pressure vessels have been conducted in the automotive industry to improve the space efficiency of trunks as well as the fuel efficiency. Compared with steel liquefied petroleum gas (LPG) vessels used in the conventional LPG vehicles, the use of type 4 composite pressure vessels has advantages in terms of reduction of the weight of vehicles. This study focused on development of type 4 composite pressure vessels that can be installed in the spare tire well. Those type 4 composite pressure vessels are designed with torispherical dome shapes instead of geodecis dome shapes because of the space limitation. To reduce deformation due to the stresses in the axial direction of the vessels, thereby securing the safety of the container, the reinforcing bar concept was applied. A structural analysis software, ABAQUS, confirmed the effect of the reinforcing bar on the axial deformation through the type 4 composite pressure vessel. As a result, the final winding angle of the composite layer was analyzed by applying $26^{\circ}/28^{\circ}/26^{\circ}/28^{\circ}/26^{\circ}/88^{\circ}$ The tensile stress was 939.2 MPa and the compressive stress was 249.3 MPa.

• Structural Engineering and Mechanics
• /
• 제30권6호
• /
• pp.713-732
• /
• 2008

Serviceability and durability of the concrete members can be seriously affected by the corrosion of steel rebar. Carbonation front and or chloride ingress can destroy the passive film on rebar and may set the corrosion (oxidation process). Depending on the level of oxidation (expansive corrosion products/rust) damage to the cover concrete takes place in the form of expansion, cracking and spalling or delamination. This makes the concrete unable to develop forces through bond and also become unprotected against further degradation from corrosion; and thus marks the end of service life for corrosion-affected structures. This paper presents an analytical model that predicts the weight loss of steel rebar and the corresponding time from onset of corrosion for the known corrosion rate and thus can be used for the determination of time to cover cracking in corrosion affected RC member. This model uses fully the thick-walled cylinder approach. The gradual crack propagation in radial directions (from inside) is considered when the circumferential tensile stresses at the inner surface of intact concrete have reached the tensile strength of concrete. The analysis is done separately with and without considering the stiffness of reinforcing steel and rust combine along with the assumption of zero residual strength of cracked concrete. The model accounts for the time required for corrosion products to fill a porous zone before they start inducing expansive pressure on the concrete surrounding the steel rebar. The capability of the model to produce the experimental trends is demonstrated by comparing the model's predictions with the results of experimental data published in the literature. The effect of considering the corroded reinforcing steel bar stiffness is demonstrated. A sensitivity analysis has also been carried out to show the influence of the various parameters. It has been found that material properties and their inter-relations significantly influence weight loss of rebar. Time to cover cracking from onset of corrosion for the same weight loss is influenced by corrosion rate and state of oxidation of corrosion product formed. Time to cover cracking from onset of corrosion is useful in making certain decisions pertaining to inspection, repair, rehabilitation, replacement and demolition of RC member/structure in corrosive environment.

• 한국안전학회지
• /
• 제27권2호
• /
• pp.78-83
• /
• 2012

This is a study to confirm how to improve and substitute the existing re-bar with other material such as a fiber rope, especially super fiber rope having much more strong tensile strength. 6(b) different fiber rope reinforced beam with a section of $20{\times}30cm$ have been made and tasted as variables designed in the study. The larger diameter of fiber rope, the more capacity of the beam, even though fiber reinforced beam are increased with ten(10)percent, each. Lower capacity of fiber-reinforced beam than normal RC beam has been analyzed theoretically and empirically, based on a lot of experiences of the same size beam test. Fiber rope-reinforced concrete beam does not have sufficient capacity than RC beam due to insufficient bonding capacity of fiber rope in concrete. It leads to decrease beam bearing capacity and crack around lower center of the beam. Therefore, bonding reinforcement of fiber rope beam such as pinning a triangles steel pin in each knot of fiber rope contributes to improving bearing capacity of fiber rope reinforcing beam.

• 동력기계공학회지
• /
• 제9권2호
• /
• pp.50-56
• /
• 2005

The mechanical properties of glass fiber reinforced polymer reinforcing bars(rebar) in various environment conditions such as moisture, chloride, alkali and freeze-thaw actions at temperature ranging from room temperature($25^{\circ}C$) to high temperature of up to $80^{\circ}C$ have been studied. The test results indicated that tensile strength and interfacial shear strength of GFRP bar were decreased with the increasing of temperature and holding time of each environment condition. The degradation in alkali environment. was more serious than those in the other environments.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.361-366
• /
• 2002

The deterioration of concrete structure due to corrosion of the reinforcement has created big financial losses on the overall industries. The volume expansion of the corrosion products causes internal pressure to concrete wall around reinforcing bar. If the maximum principal stress induced by internal pressure exceeds the tensile strength of the concrete at any point of time, a crack forms at any point of material. Therefore, in terms of life assessment of concrete structure, it is very important to predict the amount of corrosion products which induces initial concrete cracking. With this objective, this paper proposes the critical amount of corrosion products at interface between reinforcement and concrete using finite element analysis. If an actual survey of corrosion rates could be made, the model might supply information for condition assessment of existing concrete structure. As the mechanical properties of corrosion product and instantaneous geometry of corroded steel are considered in the analysis, the value obtained will be more realistic.