• Journal of the Korean Chemical Society
• /
• v.54 no.3
• /
• pp.310-316
• /
• 2010

Nanoparticle with antimicrobial property has been applied to various fields. This study added silver/platinum nanoparticles to HEMA (2-hydroxyethylmethacrylate), NVP (N-vinyl pyrrolidone) and MMA (methylmethacrylate) in various concentrations and copolymerized by heating at $70^{\circ}C$ for 40 minutes, $80^{\circ}C$ for 40 minutes, and finally, $100^{\circ}C$ for 40 minutes. The particle size of used nano silver and platinum was 10 ~ 20 nm respectively. Using the polymer produced through the copolymerization process, the authors have produced a contact lens and measured the physical characteristics which showed water content of 34.29 ~ 39.00%, refractive index of 1.422 ~ 1.430, visible transmittance of 78.8 ~ 92.5% and tensile strength of 0.149 ~ 0.179 kgf. The ophthalmic lens material produced using silver/platinum nanoparticles satisfied the basic physical properties required for contact lens application.

• Journal of the Korea Concrete Institute
• /
• v.28 no.3
• /
• pp.279-288
• /
• 2016

The present study simplified the moment-curvature relationship to straightforwardly determine the flexural behavior of reinforced concrete (RC) columns. For the idealized column section, moments and neutral axis depths at different stages(first flexural crack, yielding of tensile reinforcing bar, maximum strength, and 80% of the maximum strength at the descending branch) were derived on the basis of the equilibrium condition of forces and compatibility condition. Concrete strains at the extreme compression fiber beyond the maximum strength were determined using the stress-strain relationship of confined concrete, proposed by Kim et al. The lateral load-displacement curves converted from the simplified moment-curvature relationship of columns are well consistent with test results obtained from column specimens under various parameters. The moments and the corresponding neutral axis depth at different stages were formulated as a function of longitudinal reinforcement and transverse reinforcement indices and/or applied axial load index. Overall, curvature ductility of columns was significantly affected by the axial load level as well as concrete compressive strength and the amount of longitudinal and transverse reinforcing bars.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.5
• /
• pp.1115-1128
• /
• 1994

The condition of temperature gradients in asphaltic concrete (Ascon) pavement have been analyzed based on the data collected from 5 major sites in Korea. From this. considering heat transfer by insolation flux and air temperature within pavement slab. temperature variation on the surface of pavement was computed and numerical model using the theory of thermal conductivity was applied to estimate the temperature gradients in depth. To investigate the present condition of asphalt generally used in Korea. the asphalt property tests were applicated on 5 different AP-3 (AC 85~100), and AP-5 (AC 60~70) asphalts classified by penetration index. Uniaxial compression test and indirect tensile test were also carried out for varying temperature conditions to analyze the effect of temperature on the deformation characteristics of Ascon pavement by calculating the variation of static elastic modulus and layer coefficients.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.5
• /
• pp.403-409
• /
• 2017

In this study, mix proportioning of porous concrete with compressive strength and porosity exceeding 3MPa and 30%, respectively, was examined and then load capacity and flexural toughness of the porous concrete block were evaluated according to the different arrangements of the GFRP bars. To achieve the designed requirements of porous concrete, it can be recommended that water-to-cement ratio and cement-to-coarse aggregate ratio are 25% and 20%, respectively, under the aggregate particle distribution of 15~20mm. The failure mode of porous concrete blocks reinforced with GFRP bars was governed by shear cracks. As a result, very few flexural resistance of the GFRP was expected. However, the enhanced shear strength of porous concrete due to the dowel action of the GFRP bars increased the load capacity and toughness of the blocks. The porous concrete blocks reinforced with one GFRP bar at each compressive and tensile regions had 2.1 times higher load capacity than the companion non-reinforced block and exhibited a high ductile behavior with the ultimate toughness index ($I_{30}$) of 43.4.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.44 no.6
• /
• pp.591-596
• /
• 2011

The present study examined the physical properties of biofilms manufactured from yellowfin tuna Thunnus albacares skin gelatin with the aim of developing a biofilm from fisheries by-products to replace mammalian sources. The physical properties of biofilms from yellowfin tuna gelatin were compared with those of biofilms from porcine gelatin. The yellowfin tuna gelatin biofilm exhibited higher tensile strength (69.08 MPa) and greater elongation (14.32%) than did porcine gelatin biofilm (50.50 MPa and 10.21%, respectively). The ${\Delta}E$ and YI (yellowness index) Huntercolor values of yellowfin tuna gelatin biofilm were three-fold and 15-fold higher, respectively, than values for porcine gelatin biofilm. The opacity value of yellowfin tuna gelatin biofilm was higher than that of porcine gelatin biofilm. The stability against water of yellowfin tuna gelatin biofilm was lower than that of porcine gelatin biofilm at pH 3 to pH 11. Thermogravimetric analysis (TGA) indicated that the thermal stability of the biofilms was about $270^{\circ}C$ for porcine gelatin biofilm and about $250^{\circ}C$ for yellowfin tuna gelatin biofilm.

• Journal of Welding and Joining
• /
• v.35 no.3
• /
• pp.68-74
• /
• 2017

Characteristics of dissimilar metal welds between alloy steel ASTM A387 Gr. 91 and carbon steel ASTM A516 Gr.70 made with Flux cored arc welding(FCAW) have been evaluated in terms of microstructure, mechanical strength, chemical analysis by EDS as well as corrosion test. Three heat inputs of 15.0, 22.5, 30.0kJ/cm were employed to make joints of dissimilar metals with E71T-1C wire. Post-weld heat treatment was carried out at $750^{\circ}C$ for 2.5 h. Based on microstructural examination, Intragranular polygonal ferrite and grainboundary ferrite were formed only in first layer of weld metal. Another layers consisted of acicular ferrite and $Widmannst{\ddot{a}}tten$ ferrite. The amount of acicular ferrite was increased with decreasing heat input and layer. Heat affected zone of alloy steel showed the highest hardness due to the formation of tempered martensite and lower bainite. Lower and upper bainite were formed in heat affected zone of carbon steel. Tensile strengths of dissimilar metal welds decreased with increasing heat inputs. Dissimilar metal welds showed a good hot cracking resistance due to the low HCS index below 4. The salt spray test of dissimilar metals welds showed that the weight loss rate by corrosion below 170 hours was decreased with increasing heat inputs due to the increase of the amount of acicular ferrite.

• Elastomers and Composites
• /
• v.44 no.3
• /
• pp.315-322
• /
• 2009

Influence of blend mode of extender oil on the properties of thermoplastic vulcanizates (TPVs), based on an ethylene-propylene-diene copolymer (EPDM) and a polypropylene (PP), was studied. The EPDM/PP TPVs were prepared in an open roll mill using two different modes in blending sequence of paraffinic oil and phenolic curative, i.e., Oil-Cure and Cure-Oil modes. Degree of cross-linking by gel fraction and properties such as hardness, tensile strength, elongation at break, and melt flow rate were investigated as a function of extender oil content for the two modes. Little influence of the blend mode of extender oil on the degree of cross-linking and mechanical behaviors was observed. However, the use of Cure-Oil mode in the preparation of EPDM/PP TPVs resulted in a marked increase in the level of processability as reflected by melt flow index, as compared to the use of Oil-Cure mode.

• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.223-229
• /
• 2010

We investigated the effects of processing geometry of silica-filled isobutylene-isoprene rubber (IIR) compounds on its mechanical properties and silica dispersion, using a two roll mill and an internal mixer (banbury mixer). The compound processed with the two roll mill showed the longer induction time ($t_2$), higher maximum torque ($T_{max}$), and better silica dispersion than the compound processed with the internal mixer; however, showed slightly the lower cure index ($t_{90}$). The mechanical properties (hardness, 300% modulus, tensile strength, elongation) of the compound processed with two roll mill were higher than compound done with the internal mixer.

• Journal of the Korean Chemical Society
• /
• v.54 no.2
• /
• pp.228-233
• /
• 2010

Recently, nanoparticles of gold and silver has been applied to various fields due to antimicrobial property. This study added Ag and Au nanoparticles in HEMA (2-hydroxyethylmethacrylate), NVP (N-vinyl pyrrolidone) and MMA (methylmethacrylate) and copolymerized the solution by heating at $70^{\circ}C$ for 40 minutes, $80^{\circ}C$ for 40 minutes, and finally, $100^{\circ}C$ for 40 minutes. Using the polymer produced through the copolymerization process, and measured the physical characteristics which showed water content of 28.43% ~ 35.27%, refractive index of 1.429 ~ 1.440, visible transmittance of 79.2% ~ 86.5% and tensile strength of 0.125 kgf ~ 0.201 kgf. We judged that we made the copolymer with antimicrobial and physical properties which is suitable for conventional contact lens.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.7
• /
• pp.1459-1464
• /
• 2009

Recently demand for large-capacity aluminum heat sinks has been increased as market for high power electricity expands and high-performance electronic products develop. While the brazed heat sinks are in particular preferred, it is almost impossible to manufacture them with an atmospheric continuous furnace due to insufficient heating rate and various thickness of the parent metals. Therefore, a new index batch furnace is developed and the process variables are optimized. Then, brazing efficiency and tensile stress are obtained for brazed parts of the heat sinks. Finally experiment as well as numerical analysis has been performed to compare thermal efficiency of the brazed heat sinks with that of the silicone-bonded heat sinks.