• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.12 s.159
• /
• pp.1730-1736
• /
• 2006

To utilize hanji for fashion accessory efficiently, dyeability of Hanji should be improved. Though Hanji mostly consists of cellulose such as cotton and ramie, also has various impurities, and has the different internal and surface structure from textile materials. Because of them, Hanji might show different dyeing behavior. As physical properties of Hanji are reduced in wet condition, dyeing process would damage the physical properties of Hanji Therefore, in this study, dyeing properties of Hanji using direct dye were examined in comparison with cotton and ramie. Effect of dyeing on tensile strength, and bleeding of direct dye by water from Hanji, colorfastness to light were also estimated. While Hanji showed the maximun dye exhaustion at $25^{\circ}C$, cotton and ramie showed those at $60^{\circ}C$. Tensile strength of Hanji reduced after Hanji was dyed. When Hanji was dyed at $25^{\circ}C$, the more bleeding occurred than at higher dyeing temperature. Hanji which had higher K/S values were bled more than those had lower K/S value. Colorfastness to light of Hanji dyed with direct dye was not inferior to those of cotton and ramie.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.2
• /
• pp.145-152
• /
• 2010

This study evaluated the fatigue degradation in a SUS316L specimen using the nonlinear ultrasonic method. The nonlinearity of the ultrasonic wave was estimated by a relative nonlinear parameter defined as the ratio of the amplitudes for the fundamental wave to the second harmonic wave. In the experiment, a measurement system with contact transducers was constructed; reliable measurements were assured by keeping measurement conditions consistent and reducing extra harmonics generated in the measurement system. Two types of SUS316L specimen were used in experiments; a rotating bar fatigue specimen and a tensile fatigue specimen. The fatigue condition used was high cycle fatigue. The former specimen had a cylindrical shape and was used to observe the change in the nonlinear parameter after fatigue accumulation in a specimen. The latter was a plate-shaped specimen and was used to confirm the change in the nonlinear parameter at the position where the fatigue stress was concentrated. The measured nonlinear parameter showed a strong correlation to the damage level in both fatigue tests.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.2
• /
• pp.275-285
• /
• 2015

This experimental study presents the fatigue evaluation of a precast deck connected using Ultra-High Performance, Fiber Reinforced Concrete (UHPFRC). Four types of two identical large-scale specimens were fabricated with simplified splice rebar details which had a short splice length of ten times rebar diameter. The flexural behavior of each type of specimens until failure was investigated and fatigue behavior of the same type of specimens was then evaluated using two-million cyclic loading. In the flexural tests, tensile rebars exhibited the deformation exceeding yielding strain but failure mode related to the splice details was not observed in spite of such a short splice length. In the fatigue tests, damage was not appreciably accumulated by the cyclic loading except initial flexural cracks and the stress variations in tensile rebars was less than the allowable stress range. These experimental results demonstrate that all types of specimens exhibited acceptable fatigue performance and indicate that enhanced mechanical properties of ultra-high performance material permits to use a simplified splice details along with short joint width.

• Composites Research
• /
• v.30 no.6
• /
• pp.384-392
• /
• 2017

Sandwich panels with three different joint configurations were tested to design a novel sandwich joint structure that can effectively support both the tensile and compressive loads. The sandwich core was mainly aluminum flex honeycomb but the PMI foam core was limitedly applied to the ramp area which is transition part from sandwich to solid laminate. The face of sandwich panel was made of carbon fiber composite. For configuration 1, the composite flange and the sandwich panel were cocured. For configurations 2 and 3, an aluminum flange was fastened to the solid laminate by HI-LOK pins and adhesive. The average compressive failure loads of configurations 1, 2, and 3 were 295, 226, and 291 kN, respectively, and the average tensile failure loads were 47.3 (delamination), 83.7 (bolt failure), and 291 (fixture damage) kN, respectively. Considering the compressive failure loads only, both the configurations 1 and 3 showed good performance. However, the configuration 1 showed delamination in the corner of the composite flange under tension at early stage of loading. Therefore, it was confirmed that the structure that can effectively support tension and compressive loads at the same time is the configuration 3 which used a mechanically fastened aluminum flange so that there is no risk of delamination at the corner.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.6
• /
• pp.23-30
• /
• 2007

Round piles of Korean larch were excavated from the foundation of ex-Chosunchongdokbu (ex-Chosun Governer-General Building), which was constructed in 1916 and dismantled later in 1996. By the record (Huh, 1996), the Korean larch logs were logged from the Yalu river area near Mt. Baekdu in North Korea. At present, however, Korean larch is not so popular in South Korea. The latewood ratio profiles and strength properties (longitudinal compression, shear, longitudinal tensile, and bending) were obtained. The ratio of latewood from pith to bark increased up to 25 years, and then it showed constant tendency at 40% with some variances. From the microscopic observation, however, the latewood ratio decreased from the heartwood to the sapwood. Compression strength was greater and bending strength was a little lower than the previous reports (references 13~15), which might be attributed to the strength reduction of old structural members by aging or damage in the compression specimens than the bending ones. The flat-grained specimens for the shear and tension test showed higher coefficient of variation (COV) than the edge-grained ones. For the better comparison of results, in case of shear and tensile strength tests, the strength values of the edge-grained specimens were thought to be adopted rather than those of flat-grained ones.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.44 no.2
• /
• pp.133-139
• /
• 2018

Chemically damaged hair is vulnerable to external stimuli in daily life due to the weakened physical properties of the hair strand itself. The purpose of this work was to determine whether chemical conjugation between hair keratin proteins restores tensile strength and thus results inpreventing further deterioration under repeated combing. A model damaged hair tress was produced by a typical perm-process. Then, it was internally crosslinked by the bifunctional crosslinker (3-aminopropyl)triethoxysilane (APTES), via both silane coupling and carbodiimide chemistry. Physical properties, including tensile strength, Young's modulus, and plateau stress, were measured to verify the effect of internal crosslinking, and the existence of crosslinking was verified by Fourier transform infrared (FT-IR) spectroscopy. The degrees of hair breakage and split ends were evaluated by repeated combing-drying tests. Physical properties of chemically damaged hair were restored by internal crosslinking. Successful crosslinking of APTES via both silane coupling and carbodiimide chemistry was verified by FT-IR spectra. Prevention of breakage and split ends after repeated combing with heat was observed. Human hair can be weakened by chemical damage including perm-processing, so restoring such properties is a major issue in the hair care industry. This work shows that internal crosslinking of damaged hair via chemical conjugation would be a potent method to restore the healthy hair.

• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.547-551
• /
• 2008

Crack-free joining of $Si_3N_4\;and\;Al_2O_3$ using 15 layers has been achieved by a unique approach introducing Sialon polytypoids as a functionally graded materials (FGMs) bonding layer. In the past, hot press sintering of multilayered FGMs with 20 layers of thickness $500{\mu}m$ each has been fabricated successfully. In this study, the number of layers for FGM was reduced to 15 layers from 20 layers for optimization. For fabrication, model was hot pressed at 38 MPa while heating up to $1700^{\circ}$, and it was cooled at $2^{\circ}$/min to minimize residual stress during sintering. Initially, FGM with 15 layers had cracks near 90 wt.% 12H / 10 wt.% $Al_2O_3$ and 90 wt.% 12H/10 wt.% $Si_3N_4$ layers. To solve this problem, FEM (finite element method) program based on the maximum tensile stress theory was applied to design optimized FGM layers of crack free joint. The sample is 3-dimensional cylindrical shape where this has been transformed to 2-dimensional axisymmetric mode. Based on the simulation, crack-free FGM sample was obtained by designing axial, hoop and radial stresses less than tensile strength values across all the layers of FGM. Therefore, we were able to predict and prevent the damage by calculating its thermal stress using its elastic modulus and coefficient of thermal expansion. Such analyses are especially useful for FGM samples where the residual stresses are very difficult to measure experimentally.

• Membrane Journal
• /
• v.28 no.6
• /
• pp.406-413
• /
• 2018

In OBIGGS, a small amount of ozone in the atmosphere damages the polymer membrane. Therefore, the ozone removal device is installed at the front end to prevent the damage of the membrane by reducing the concentration of ozone in the gas delivered to the membrane. In this study, two hollow fiber membranes, PI and PSf, used to fabrication hollow fiber module with an effective membrane area of $6.37cm^2$ for gas separation in OBIGGS. The ozone concentration in the chamber was maintained at 2-3 ppm. The gas was continuously supplied into the module by using a pump. The gas permeation characteristics and the tensile strength were evaluated as a function of ozone exposure time. The PI-based hollow fiber membrane showed only 20% reduction in the transmittance, and remained its original uniformity without any significant changes. However, when PSf type hollow fiber membranes were used, the permeability decreased by more than 80% and the tensile strength decreased by more than 70%.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.7
• /
• pp.203-210
• /
• 2019

A recent earthquake on the Korean Peninsula caused much damage to masonry buildings, and research on performance evaluation has been underway. A masonry building is generally constructed using wet construction and is affected by temperature, which reduces the efficiency of the construction. In this study, we propose a dry construction technique for assembling concrete blocks without using mortar and evaluated its performance through experimental and analytical research. To evaluate the performance, experiments were carried out for the prismatic compressive strength, direct terminal strength, and diagonal tensile strength of the dry construction wall. The adequacy of the cross section shape was also reviewed through FEM analysis. The results show that the compressive strength and diagonal tensile strength could exert a certain intensity or higher. Furthermore, the H-type module of a key block acted as a shear key for the entire concrete block, which resulted in excellent shear strength performance. In addition, the shape and thickness of the main block have a major effect on the strength performance of each block. Therefore, an optimal shape and the proposed dry construction method could be applied to replace the wet method by studying the construction or seismic performance of the proposed method.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.48 no.2
• /
• pp.169-180
• /
• 2022

Streptococcus sp. is generally known as a strain that produces hyaluronic acid. In this study, we focused on ingredients other than hyaluronic acid among several metabolites produced by Streptococcus sp. during cultivation. The hair experimental sample (HAIRCLE^TM) was prepared with Streptococcus sp. culture filtrate under the condition that hyaluronic acid was not produced and the effect on the hair was identified. Tensile strength of hair was tested with a universal testing machine (UTM). Surface properties of a hair were examined with an atomic force microscope (AFM). Our results suggest that HAIRCLE^TM could prevent damage to a hair such as destroyed-cuticle, increased-faction force, and broken-hair. Furthermore, hair-related experiments confirmed that HAIRCLE^TM could promote the expression of hair growth factors VEGF, HGF, and Wnt10b and mitigate male hair loss by inhibiting androgen receptors and TGF-β2 expression. In addition, it was confirmed that the expression of barrier-related factors (INV, CLDN-1) was increased for oxidative stress, and the COX-2 expression, an inflammatory factor, was inhibited, thereby improving damaged scalp barriers and alleviating induced inflammation.