• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.146-149
• /
• 2007

The effects of boron additions in steels have long been recognized as very important, mainly with respect to hardnability of heat treatable steels. The systematics of structure and properties of boron steels will then be illustrated in the context of low-alloy steels with carbon contents raging from 0.05 to 0.25% and boron contents 0-130 ppm. we investigated the effect of the microstructure and mechanical properties with heat treatment condition of the boron-treated(0.0013 ppm) low carbon(0.2 %C) low alloy steel. The specimens were austenitised for 5 and 10, 15 min at $880{\sim}940^{\circ}C$(with/without tempered at 150, 180 and $210^{\circ}C$ for the various periods of time from 60 min to 120 min) After heat treatment, mechanical properties were measured by tensile test and hardness test. For analysis of microstructure, Optical/SEM analysis and XRD were carried out.

• 대한금속재료학회지
• /
• 제50권7호
• /
• pp.517-522
• /
• 2012

In this study, a super carburizing treatment was applied to improve roller pitting fatigue life. It produced excellent properties of surface hardness and temper softening resistance by forming precipitation of fine and spherodized carbides on a tempered marstensite matrix through the repeated process of carburization and diffusion after high temperature carburizing step 1. The cycle II performed two times carburizing/diffusion cycle (process) after super carburization at $1,000^{\circ}C$ had fine and spherodized carbides to subsurface $200{\mu}m$. In this case, the carbide was $(Fe,Cr)_3C$ and there was not any massive carbides. In the case of Cycle II, the roller pitting fatigue life had a 6.15 million cycles. It was improved 48% compared to normal gas carburizing treatment.

• 한국분말재료학회지
• /
• 제26권2호
• /
• pp.112-118
• /
• 2019

Infiltration is a popular technique used to produce valve seat rings and guides to create dense parts. In order to develop valve seat material with a good thermal conductivity and thermal expansion coefficient, Cu-infiltrated properties of sintered Fe-Co-M(M=Mo,Cr) alloy systems are studied. It is shown that the copper network that forms inside the steel alloy skeleton during infiltration enhances the thermal conductivity and thermal expansion coefficient of the steel alloy composite. The hard phase of the CoMoCr and the network precipitated FeCrC phase are distributed homogeneously as the infiltrated Cu phase increases. The increase in hardness of the alloy composite due to the increase of the Co, Ni, Cr, and Cu contents in Fe matrix by the infiltrated Cu amount increases. Using infiltration, the thermal conductivity and thermal expansion coefficient were increased to 29.5 W/mK and $15.9um/m^{\circ}C$, respectively, for tempered alloy composite.

• 한국산업융합학회 논문집
• /
• 제26권5호
• /
• pp.725-731
• /
• 2023

In this study, the harmless crack size was evaluated using carburized, quenched-tempered SCM822H steel. The possibility of detecting cracks that reduce the fatigue limit by non-destructive inspection was evaluated. The conclusions obtained are as follows. The retained austenite of surface was reduced by SP. About 35% and 65% of the retained austenite on the surface were transformed into strain-induced martensite, increasing the hardness by 79HV and 122HV over the as-received material. The maximum compressive residual stresses introduced on the surfaces were -695 MPa and -688 MPa, respectively. The fatigue limit increased by 1.48 times and 1.67 times, respectively, compared to the as-received material. The harmless crack size of SP specimen was determined differently depending on the shot ball size.

• 한국주조공학회지
• /
• 제20권2호
• /
• pp.104-109
• /
• 2000

Three different white cast irons alloyed with Cr, V, Mo and W were prepared in order to study their abrasion wear behavior in as-cast and heat-treated conditions. The specimens were produced using a 15㎏-capacity high frequency induction furnace. Melts were super-heated to $1600^{\circ}C$, and poured at $1550^{\circ}C$ into Y-block pepset molds. Three combinations of the alloying elements were selected so as to obtain the different types of carbides : 3%C-10%Cr-5%Mo-5%W(alloy No. 1: $M_7C_3$ and $M_6C$), 3%C -10%V-5%Mo-5%W(alloy No. 2: MC and $M_2C$) and 3%C-17%Cr-3%V(alloy No. 3: $M_7C_3$ only). A scratching type abrasion test was carried out in the states of as-cast(AS), homogenizing(AH), air-hardening(AHF) and tempering(AHFT). First of all, the as-cast specimens were homogenized at $950^{\circ}C$ for 5h under the vacuum atmosphere. Then, they were austenitized at $1050^{\circ}C$ for 2h and followed by air-hardening in air. The air-hardened specimens were tempered at $300^{\circ}C$ for 3h. 1 ㎏ load was applied in order to contact the specimen with abrading wheel which was wound by 120 mesh SiC paper. The wear loss of the test piece(dimension: $50{\times}50{\times}5$ mm) was measured after one cycle of wear test and this procedure was repeated up to 8 cycles. In all the specimens, the abrasion wear loss was found to decrease in the order of AH, AS, AHFT and AHF states. Abrasion wear loss was lowest in the alloy No.2 and highest in the alloy No.1 except for the as-cast and homogenized condition in which the alloy No.3 showed the highest abrasion wear loss. The lowest abrasion wear loss of the alloy No.2 could be attributed to the fact that it contained primary and eutectic MC carbides, and eutectic $M_2C$ carbide with extremely high hardness. The matrix of each specimen was fully pearlitic in the as-cast state but it was transformed to martensite, tempered martensite and austenite depending upon the type of heat-treatment. From these results, it becomes clear that MC carbide is a significant phase to improve the abrasion wear resistance.

• 플랜트 저널
• /
• 제10권2호
• /
• pp.48-59
• /
• 2014

본 연구에서는 고온 고압 배관용 단조밸브 용접부의 품질확보를 위하여 단조밸브 제작현장에서 활용할 용접후열처리의 유지시간 및 유지온도를 연구했다. ASTM A182 F92 재료를 단조밸브의 용접부에 해당되는 밸브 끝단부 및 누설방지용접부와 동일한 형상의 두께 1 inch 쿠폰으로 가공하고, 쿠폰을 가스 텅스텐 아크용접(GTAW: Gas Tungsten Arc Welding) 방법으로 완전용입 용접하여 시편을 제작했다. 용접부 호칭두께가 1 inch인 시편을 $705^{\circ}C$, $735^{\circ}C$, $750^{\circ}C$, $765^{\circ}C$, $795^{\circ}C$ 및 $825^{\circ}C$에서 1시간 유지하여 용접후열처리를 실시(Group 1)하였다. 그리고 용접부 호칭두께가 1 inch인 시편 3개를 $735^{\circ}C$에서 30분, 1시간 및 2시간으로 달리 유지(Group 2)하여 용접후열처리를 실시하였다. 다른 유지시간과 유지온도에 따른 경도의 변화를 관찰하기 위하여 모재부, 열영향부 및 용착금속부에서 경도를 측정하였다. 본 실험의 결과에 따라, 1 inch당 1시간 온도를 유지할 경우는 용접후열처리가 $750^{\circ}C{\sim}765^{\circ}C$에서 수행되어야 바람직한 것으로 확인되었다. 단조밸브 제작규격에서 요구하는 최소 유지온도 보다 $5^{\circ}C$가 높은 $735^{\circ}C$에서 1 inch당 1시간 유지할 경우에 요구된 경도 값을 만족하지 못하여, 요건보다 긴 시간인 1 inch당 2시간 용접후열처리 시 경도 값을 만족하는 것으로 확인되었다. 또한 용착금속부의 조직은 템퍼드-마르텐사이트 조직으로 확인되었다.

• 한국산학기술학회논문지
• /
• 제13권2호
• /
• pp.471-477
• /
• 2012

SCM420재질의 기어를 담금질을 실시한 후 초경호브(Hob)에 PACVD 코팅처리 후 표면경도가 높은 표면(HRC 60)을 절삭하였다. 코팅처리 없이 난삭재(難削材)로 분류되는 경도가 큰것, 경한 물질을 포함한 것, 강도가 높은 것에 공구수명과 생산성을 향상에는 한계성을 가지고 있다. 이를 개선하기 위해 초경호브에 TiCN코팅처리 전후에 대하여 Skiving 절삭으로 코팅처리 한 호브가 가공성이 좋고, 공구마멸이 적어, 공구수명이 2.5배 증가하는 결과를 얻었다. 실험은 CNC 스카이빙 호빙머신을 이용하여 습식절삭으로 절삭속도와 이송량으로 다양한 조건을 적용하여 공구마멸과 표면거칠기 데이터를 얻었다. 실험결과 조건 2에서(V=200m/min F=0.7mm/rev) Cutting speed가 절삭표면에 Feed Mark가 미세하고, 표면거칠기는 Rmax $4.7{\mu}m$(Ra $1.19{\mu}m$)의 데이터를 얻었다.

• 열처리공학회지
• /
• 제13권1호
• /
• pp.27-34
• /
• 2000

This present study were investigated effect of Ni contents on the microstructure and strength characteristic in 9Cr ferritic heat-resistant steel added 1.7%W in place of Mo in order to restrain laves phase formation. The result obtained from this study are as follow. Volume fraction, number of particles per unite area and particle size of carbide decreased with increase of Ni contents. Other side, carbides of $M_{23}C_6$ type was mainly precipitated in this steel, but laves phases could not precipitated in spite of increasing of aging time. With increase of tempering temperature, hardness was increased, and maximum value was showed around 873k by secondary hardening due to precipitation of $W_2C$ type carbide and then, was decreased. Tensile and yield strength due to decrease precipitation amount of carbide and number of particles per unite area was decreased, but elongation and impact value was increased. In case of aged specimen after tempering than tempered specimen, strength was higher and elongation was lower due to increasing of precipitated amount of carbide and number of particles per unite area.

• 비파괴검사학회지
• /
• 제20권5호
• /
• pp.390-396
• /
• 2000

원자로 재료인 SA 508 Class 3 강용접부 및 열영향부 모사 시험편에 대해서 초음파공명분광법으로 동적탄성계수를 측정하였다. 등방성 탄성계수를 가정하여 초기 추정 탄성 계수, $c_{11},\;c_{12}$ 및 $c_{44}$로부터 장방형 시편의 공명 주파수를 계산하였으며 계산된 주파수와 초음파공명분광법으로 측정된 주파수를 비교, 반복 수렴 절차를 거쳐 정밀한 탄성계수를 구했다. 열처리 조건의 차이 및 미세 조직의 차이에 따라 영률 및 전단 계수의 차이가 확실하게 나타났다. 미세한 베이나이트 조직에서의 영률 및 전단 계수는 조대한 마르텐사이트 조직보다 높았으며 이러한 경향은 미세 경도 시험 등의 다른 실험 결과와도 일치하였다.

• Journal of Applied Biological Chemistry
• /
• 제54권3호
• /
• pp.147-152
• /
• 2011

고구마 분말을 첨가한 뻥튀기 제조 시 팽화시간, 팽화온도, 수분함량과 같은 팽화조건을 달리하여 물리적 및 관능적 품질 특성을 조사하였다. 실험 결과, 색도에서 수분함량은 유의적 차이를 나타내지 않았지만 팽화온도와 팽화시간이 증가함에 따라 $L^*$값이 감소하고, $a^*$값과 $b^*$값이 증가하였다. 비체적은 팽화시간, 팽화온도, 수분함량이 증가할수록 일반 고구마 뻥튀기의 비체적도 증가하였으며, 파괴력은 낮은 수분함량, 높은 팽화온도, 오랜 팽화시간에서 높게 나타났다. 또한 외관, 색, 향, 조직감, 맛에 대한 패널들의 전체적인 기호도를 나타낸 관능평가에서는 수분함량 및 팽화온도가 높고, 오랜 팽화시간 하에 제조된 시험구가 우수하게 평가되었다.