• 한국수소및신에너지학회논문집
• /
• 제22권1호
• /
• pp.29-34
• /
• 2011

This study examined the effect of environmental variables, such as the NaOH concentration and solution temperature, on the rate of hydrogen generation from NaOH solutions through the corrosion of used aluminum cans as a potential candidate material for the safe and economic production of hydrogen. Corrosion of the used aluminum cans was promoted by increasing the NaOH concentration and solution temperature because of the loss of aluminum passivity. The measured rate of hydrogen generation from the NaOH solutions increased with increasing NaOH concentration due to the catalytic activity of NaOH in the hydrolysis process. However, at higher solution temperatures, the rate of hydrogen generation rate was less affected by the NaOH concentration than that at lower temperature.

• 한국재료학회지
• /
• 제27권12호
• /
• pp.643-651
• /
• 2017

Four types of high Mn TWIP(Twinning Induced Plasticity) steels were fabricated by varying the Mn and Al content, and the tensile properties were measured at various strain rates and temperatures. An examination of the tensile properties at room temperature revealed an increase in strength with increasing strain rate because mobile dislocations interacted rapidly with the dislocations in localized regions, whereas elongation and the number of serrations decreased. The strength decreased with increasing temperature, whereas the elongation increased. A martensitic transformation occurred in the 18Mn, 22Mn and 18Mn1.6Al steels tested at $-196^{\circ}C$ due to a decrease in the stacking fault energies with decreasing temperature. An examination of the tensile properties at $-196^{\circ}C$ showed that the strength of the non-Al added high Mn TWIP steels was high, whereas the elongation was low because of the martensitic transformation and brittle fracture mode. Although a martensitic transformation did not occur in the 18Mn1.9Al steel, the strength increased with decreasing temperature because many twins formed in the early stages of the tensile test and interacted rapidly with the dislocations.

• 대한치과기공학회지
• /
• 제35권2호
• /
• pp.127-136
• /
• 2013

Purpose: In order to find out the impact of changes in polymerization conditions of orthodontic acrylic resin on maximum load. Methods: While maintaining mixing ratio 3:1 of polymer and monomer in spray-on way in the production condition of polymerization temperature $25^{\circ}C$ or $37^{\circ}C$ for 10 minutes or 30 minutes of polymerization time by pressure $3kfg/cm^2$ or $6kfg/cm^2$ in the lab maintaining $25^{\circ}C$ of room temperature, the change in maximum load rise rate was tested by producing 5 acrylic resin specimens for orthodontics per group to meet the standards of $25mm{\times}2mm{\times}2mm$ and using INSTRON with the 3rd bar 2mm in diameter and parallel support bending device of $15{\pm}0.1mm$ as test equipment showing 30.00mm/min of crosshead speed, $50{\pm}16$ N/min of load ratio in the laboratory of $24^{\circ}C$ room temperature and as a result, the following results were obtained. Results: 1. When increasing pressure from $3kfg/cm^2$ to $6kfg/cm^2$, maximum load was lowered by -4.285%. 2. When increasing polymerization time from 10 minutes to 30 minutes, maximum load rose by 3.848%. 3. When increasing polymerization temperature from $27^{\circ}C$ to $37^{\circ}C$, maximum load rose by 5.854%. Conclusion: Considering the above test results that polymerization time and polymerization temperature when polymerizing acrylic resin for orthodontics according to changes in working conditions had an impact on the rate of rise of maximum load values but the rate of rise was lowered when increasing pressure from $3kfg/cm^2$ to $6kfg/cm^2$, we came to a conclusion that high pressure more than necessary does not affect the rate of rise of maximum load.

• 한국결정성장학회지
• /
• 제9권6호
• /
• pp.563-569
• /
• 1999

수평형 반응로에서 $TMS[Si(CH_3)_4]-H_2$ 와 H$_2$가스를 이용하여 SiC 초미분말 합성시 최적 공정 조건을 알아보기 위하여 수치모사방법을 이용하였다. 이론적인 해석 결과, 반응온도가 증가함에 따라 TMS의 전환률은 증가하였지만, 수소유량이 증가함에 따라서는 TMS 전환률이 감소하였다. 또한 반응온도가 높을수록 기상의 충돌확률이 증가하여 최종 생성된 SiC 입자농도는 감소하였지만, 수소유량과 TMS 농도가 증가하는 경우에서는 생성된 입자농도가 증가하였다. 한편 입자크기는 반응온도와 초기 TMS 농도가 증가함에 따라 증가하였지만 수소유량이 증가하는 결향을 나타내었다. 이러한 반응온도, 수소유량 및 TMS 농도에 따른 입자크기 변화는 실제 실한 결과와 이론적으로 고찰한 결과가 일치하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2012년도 제45회 KOSCO SYMPOSIUM 초록집
• /
• pp.149-152
• /
• 2012

The laboratory experiments have been conducted to investigate the effects of air preheated temperature on the emission characteristics by a model gas turbine burner with a hybrid/dual swirl jet flames configuration. The concentration of NOx and CO emissions, and flue gas temperature at combustor exit were measured with varying the equivalence ratio for different air preheated temperatures of 300, 400, 500K at atmospheric pressure. It was overall shown that the NOx and CO emissions, and flue gas temperature were decreased according to the decreasing of equivalence ratio due to the effects of lean premixed combustion regardless of the air preheated temperature. Experimental results of a lean premixed flames configuration indicated that the NOx emission was increased with higher inlet air temperature and air flow rate, which is attributed to the increasing of flue gas temperature and heat release related to the thermal NOx mechanism. But the CO emission was shown the opposite tendency, that is, the CO emission was decreased with increasing of inlet air temperature and flow rate.

• Transactions on Electrical and Electronic Materials
• /
• 제6권4호
• /
• pp.164-168
• /
• 2005

Effects of high-temperature slurry were investigated on the chemical mechanical polishing (CMP) performance of tetra-ethyl ortho-silicate (TEOS) film with silica and ceria slurries by the surface analysis of X-ray photoelectron spectroscopy (XPS). The pH showed a slight tendency to decrease with increasing slurry temperature, which means that the hydroxyl $(OH^-)$ groups increased in slurry as the slurry temperature increased and then they diffused into the TEOS film. The surface of TEOS film became hydro-carbonated by the diffused hydroxyl groups. The hydro-carbonated surface of TEOS film could be removed more easily. Consequently, the removal rate of TEOS film improved dramatically with increasing slurry temperature.

• 생약학회지
• /
• 제38권1호
• /
• pp.56-61
• /
• 2007

This study was carried out to investigate the optimum conditions for extraction of acidic polysaccharides from red ginseng marc produced by manufacturing alcoholic extract from red ginseng. Method of carbazole-sulfuric acid was applied to determine the amount of acidic polysaccharides in red ginseng marc. The amounts of acidic polysaccharides in water extract of red ginseng marc were increased with increasing extraction temperature. The contents of acidic polysaccharides were not significantly different despite of the extraction time increasing from 6 hours to 48 hours. The contents of starch in water-extract of red ginseng marc were increased with increasing extraction temperature. The starch amounts in water extract of red ginseng marc extracted for 48 hours were increased. The yields of polysaccharide precipitated from water-extract of red ginseng marc were increased with increasing extraction temperature. The hydration rate of acidic polysaccharides and starch from water-extract of red ginseng marc were decreased with increasing extraction temperature. The contents of starch were not significantly different despite of the extraction time increasing from 6 hours to 48 hours at $8^{\circ}C$. However, the rehydration rate of acidic polysaccharide for 48 hours were decreased at $8^{\circ}C$. The rehydration rate of acidic polysaccharide and starch extracted from 6 hours to 24 hours at $25^{\circ}C$ were not significantly different, but those extracted for 48 hours were increased. From the above results, we suggest that by altering the extraction conditions in red ginseng marc it is possible to develop optimum conditions for extraction that modulate the proportions of acidic polysaccharide and starch.

• 오토저널
• /
• 제4권3호
• /
• pp.24-39
• /
• 1982

It has already been known that quenching effect is influenced greatly by stirring and changing coolant's temperature on quenching. But according to the past investigations its effect has not been taken into consideration quantitatively in the cooling process. The purpose of this study is that the influence of flow rate and temperature on the quenching effect of cooling water as quenching medium is quantitatively examined by using the open channel. The stream of water in this study is turbulent flow. The temperature of the specimen made of pure copper is measured by CA thermocouple in the vicinity of the surface and recorded by an automatic recorder during the quenching process in city water. The results obtained are as follows; 1. The quenching effect of cooling water generally increases with Reynolds Number(characteristic length; specimen diameter)as shown in the experimental formula; but at the realm of Reynolds Number from 1.2 * 10$^{4}$ to 9.2 * 10$^{4}$, the increasing rate of quenching effect shows little increase. 2. The increasing rate of quenching effect was increased under the flow rate of 221 cm/sec. On the other hand, it was decreased below this flow rate. 3. The quenching effect was influenced by the water temperature and the flow rate. But it was rather dependent upon the former than the latter. 4. Although the quenching effect appeared loosely in the water temperature of 50.deg. C, it was shown that the quenching effect increased in the low flow rate of 31 cm/sec. comparing with the still water. 5. It is desirable to design the quenching system to be over 1.2 * 10$^{4}$ in Reynolds Number or over, 3000$cm^{-1}$ / in V/v in order to increase the quenching effect of the system using open channel.annel.

• 대한설비공학회지:설비저널
• /
• 제16권3호
• /
• pp.295-304
• /
• 1987

The purpose of this study is to develop a computer model for simulating the water-lit hium bromide absorption heat transformer (AHT) Including all major components and to find the flexibility in operation. The effect of source hot water temperature, cooling water temperature, useful hot water flow rate, cooling water flow rate and evaporator circulation flow rate were investigated. The coefficient of performance (COP), temperature boost $({\Delta}T\;=\;T_A\;-\;Ti)$ and concentration variations can be predicted. The performance study indicates that the performance of AHT increases for the waste hot water temperature increasing and with a decrease of the cooling water temperature. The effect on performances of useful hot water flow rape is significant except on temperature boost. Also the effects on performance of cooling water flow rate and evaporator circulation flow rate are small. It is shown that the computer program is valuable to predict the performance of absorp-tion heat transformer units at various working corditions.

• 한국산학기술학회논문지
• /
• 제19권8호
• /
• pp.32-36
• /
• 2018

500kgf 용량의 Instron 시험기를 이용하여 폴리프로필렌 판재의 인장시험 평가를 행하였다. 두께가 0.8 mm인 폴리프로필렌 판재의 변형속도민감도를 평가하기 위하여 변형속도는 $5{\times}10^{-4}/sec{\sim}5{\times}10^{-2}/sec$으로 100배 변화를 주어 상온 및 고온인장시험 하였다. 이를 통하여 변형속도 및 온도 변화에 따른 강도변화를 비교하였다. 실험결과 초기 변형속도가 증가할수록 강도가 증가하였으며 이는 폴리프로필렌은 변형속도민감도가 강한 양의 값을 지닌 재료임을 알 수 있었다. 또한 폴리프로필렌 판재의 고온 인장특성을 평가하기 위하여 온도는 80, 120, $160^{\circ}C$로 변화시켜 시험하였다. 고온인장시험 결과 온도가 증가할수록 강도는 감소하였으며 특히 $160^{\circ}C$에서는 강도가 인장강도가 0으로 강하하였다. 변형속도 증가에 따른 온도 증가의 영향을 살펴보면 상온, $80^{\circ}C$ 및 $120^{\circ}C$까지는 항복강도 및 인장강도의 증가 폭이 비슷한 수준을 나타내었으나 $160^{\circ}C$에서는 응력이 0에 가까워짐에 따라 강도 증가가 거의 없는 것으로 나타났다. 고온 인장시험에서 변형속도 증가에 따라 항복강도 값이 증가하는 양 보다는 인장강도 값이 증가하는 폭이 컸다.