• Proceedings of the IEEK Conference
• /
• 2000.06b
• /
• pp.24-27
• /
• 2000

Ferroelectric P $b_{0.99}$〔(Z $r_{0.6}$S $n_{0.4}$)$_{0.9}$ $Ti_{0.1}$〕$_{0.98}$N $b_{0.02}$ $O_3$(PNZST) thin films were deposited by a RF magnetron sputtering on (L $a_{0.5}$S $r_{0.5}$)Co $O_3$(LSCO)/Pt/Ti/ $SiO_2$/Si substrate using a PNZST target with excess PbO of 10 mole％. The thin films deposited at the substrate temperature of 500 $^{\circ}C$ were crystallized to a perovskite phase after rapid thermal annealing(RTA) The thin films annealed at 650 $^{\circ}C$ for 10 seconds in air exhibited the good crystal structures and ferroelectric properties. The remanent polarization and coercive field of the PNZST capacitor were about 20 $\mu$C/$\textrm{cm}^2$ and 50 kV/cm, respectively. The reduction of the polarization after 2.2$\times$10$^{9}$ switching cycles was less than 10 ％.0 ％.％.0 ％.0 ％.

• Nuclear Engineering and Technology
• /
• v.52 no.9
• /
• pp.1896-1906
• /
• 2020

The BEAVRS (Benchmark for Evaluation and Validation of Reactor Simulation) benchmark calculations were performed by DeCART stand-alone and DeCART/MATRA multi-physics coupled code system to verify their accuracy. The solutions of DeCART stand-alone calculations for the control rod bank worth, detector signal, isothermal temperature coefficient, and critical boron concentration agreed very well with the measurements. The root-mean-square errors of the boron letdown curves for two-cycles were less than about 20 ppm, while the individual and total control rod bank worth agreed well within 7.3% and 2.4%, respectively. For the BEAVRS benchmark calculations at the beginning of burnup, the difference between DeCART simplified thermal-hydraulic stand-alone and DeCART/MATRA coupled calculations were not significantly large. Therefore, it is concluded that both the DeCART stand-alone code and the DeCART/MATRA multi-physics coupled code system have the capabilities to generate high fidelity transport solutions at core follow calculations.

• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.285-291
• /
• 2009

In this work, durability characteristics of electrorheological (ER) fluid for damper application are experimentally investigated. ER fluid is prepared by using phosphorated starch particles and silicone oil. The field-dependent Bingham characteristics and response time for the proposed ER fluids are experimentally obtained. Experimental apparatus of durability test for ER fluid is established with cylindrical ER cylinder for mid-sized passenger vehicle. In order to evaluate the durability characteristics of ER fluid as a function of time, damping force and temperature variations are measured until one million cycles. After durability test, Bingham characteristics and response time of ER fluid are measured and compared to the initial properties. Microscopic pictures of ER fluid are taken to validate the changes of properties. The results indicate that the ER fluid can be commercially utilized in vehicle damper system with its durability performance. Moreover, the understanding of durability characteristics is essential to predict the service life of ER fluid as well as to design its applications.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.15 no.3
• /
• pp.114-121
• /
• 2007

In this study, a modified reverse flow type, one of the triple effect absorption cycles, is studied for performance improvement. The cycle simulation is carried out by using EES(Engineering Equation Solver) program for the working fluid of $H_2O/LiBr$ solution. The split-ratios of solution flow rate, UA of each component, pumping mass flow rate of solution are considered as key parameters. The results show that the optimal SRH (split ratio of high side) and SRL (split ratio of low side) values are 0.596 and 0.521, respectively. Under these conditions, the COP is maximized to 2.1. The optimal pumping mass flow rate is selected as 3 kg/s and the corresponding UAEV A is 121 kW/K in the present system. The present simulation results are compared to the other literature results from Kaita's (2002) and Cho's (1998) triple effect absorption systems. The present system has a lower solution temperature and a higher COP than the Kaita's modified reverse flow, and it also gives a higher COP than the Cho's parallel flow by adjusting split ratios.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.15 no.1
• /
• pp.34-45
• /
• 2007

In order to reduce the compression power and to use the overall energy contained in LNG effectively, a combined cycle is devised and simulated. The combined cycle is composed of two cycles; one is an open cycle of liquid/solid carbon dioxide production cycle utilizing LNG cold energy in $CO_2$ condenser and the other is a closed cycle gas turbine which supplies power to the $CO_2$ cycle, utilizes LNG cold energy for lowering the compressor inlet temperature, and uses the heating value of LNG at the burner. The power consumed for the $CO_2$ cycle is investigated in terms of a solid $CO_2$ production ratio. The present study shows that much reduction in both $CO_2$ compression power (only 35% of the power used in conventional dry ice production cycle) and $CO_2$ condenser pressure could be achieved by utilizing LNG cold energy and that high cycle efficiency (55.3% at maximum power condition) in the gas turbine could be accomplished with the adoption of compressor inlet cooling and regenerator. Exergy analysis shows that irreversibility in the combined cycle increases linearly as a solid $CO_2$ production ratio increases and most of the irreversibility occurs in the condenser and the heat exchanger for compressor inlet cooling. Hence, incoming LNG cold energy to the above components should be used more effectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1151-1157
• /
• 2012

Ocean Thermal Energy Conversion(OTEC) technology is one of the new and renewable energy that utilizes the natural temperature gradient that exists in the tropical ocean between warm surface water and the deep cold water, to generate electricity. The selection of working fluid and the OTEC cycle greatly influence the effect on the system operation, and it's energy efficiency and impacts on the environment. Working fluids of the OTEC are ammonia, R22, R407C, and R410A. In this paper, we compared boiling pressure to optimize OTEC system at $25^{\circ}C$. Also, this paper showed net-power and efficiency according to working fluids for closed cycle and regeneration cycle.

• Textile Coloration and Finishing
• /
• v.23 no.3
• /
• pp.179-186
• /
• 2011

For the application of Jeju scoria scattered around the island as a natural dye, cotton fabrics were dyed with the dye and their properties were measured including dyeability, colorfastness, antibacterial activity, deodorization efficiency, ultraviolet protection, and far-infrared emission. The dyed cotton fabrics were in yellowish red and optimal dyeing conditions were obtained with a colorant concentration of 25%(o.w.b) at a temperature of $80^{\circ}C$ for the dyeing time of 120 minutes. The ratings of colorfastness to light, rubbing, perspiration, and washing were 8, 5, 5, and 4~5 respectively. After 15 wash cycles, colorfastness remained as much as 4~5 rating. The cotton fabric dyed with Jeju scoria demonstrated excellent antimicrobial activity and deodorization efficiency of 99.9% and 93.9% respectively. Ultraviolet protection factor was 50+. Far-infrared emission rate and far-infrared emission intensity were 90% and 362(W/$m^2{\cdot}{\mu}m$) respectively. The Jeju scoria can be introduced as a new colorant for the natural dyeing of cotton.

• Textile Coloration and Finishing
• /
• v.24 no.3
• /
• pp.173-179
• /
• 2012

Silk fabric treated with fluorocarbon resins (Asahi Guard AG-7005 and AG-E061) were washed and subsequently heat treated varying the washing cycles and the temperature. After the processing, the water and oil repellencies, and contact angle to water were evaluated. The water and oil repellencies decreased by the washing and recovered by following heat treatment. Also ESCA measurement was carried out to investigate the surface chemical composition of the treated fiber. The $F_1s$ intensity of the treated fabric decreased by the washing and recovered by the subsequent heat treatment. On the other hand, the $O_1s$ intensity increased by the washing and decreased by following heat treatment. From the results, it is clear that change of the water and oil repellencies of the silk fabric treated with fluorocarbon resin occurred by the washing and subsequent heat treatment. Considering a change of the water repellency of the silk fabric treated with fluorocarbon resin, it seems likely that the fluoroalkyl group of the fluorocarbon resin rotates from surface to inside of the fiber by the washing to adapt to the hydrophilic circumstance, and the orientation of the fluoroalkyl groups of the resin disturbed by the washing recovers the orientation to the fiber surface after the subsequent heat treatment.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.33 no.1
• /
• pp.27-37
• /
• 1997

The aim of the present study is to investigate experimentally the mechanism of an exploding wire in water and also to observe the bubble motion induced by an exploding wire. The experiment of an exploding wire is carried out in a water tank. As a metallic wire, a tungsten wire of 0.2mm in diameter and 10mm in length is employed. The electric energy of 50-300J is fed to the wire from a capacitor of 100$\mu$F charged up to 1-2.5kV. The explosion is recorded by a CCD camera with the resolution of 1$\mu$sec. The explosion process of metallic wire is divided into three phases. Phase 1 : As the voltage is applied to the wire, the temperature increases due to Joule heating and the wire emits light. Phase 2 : Then the wire melts and the cylindrical plasma is formed between the electrodes. Up to this stage, strong light emission is observed. Phase 3 : The light emission goes out and a vapor bubble begins to grow spherically. The radius of a bubble oscillates in time, but the amplitude of oscillation diminishes in several cycles.

• Journal of Microbiology and Biotechnology
• /
• v.10 no.6
• /
• pp.873-876
• /
• 2000

Short tendem repeat (STR) loci have been used in the field of forensic science. There are literally hundreds of STR systems which have been mapped throughout the human genome. These STR loci are found in almost every chromosome in the genome. They may be amplified using a variety of PCR primers. In this study, a DNA genotyping system based on the multiplex amplification of highly polymorphic STR loci was developed. Three STR loci with nonoverlapping allele size ranges have been utilized in the multiplex amplification including the Neurotensin receptor gene, D21S11, and Human tyrosine hydroxylase gene. The optimal condition for triplex PCr was obtained in a solution with a total volume of $25{\mu}l$ containing 2.0 U of Taq polymerase, 3 mM of $MgCl_2$, $300{\mu}M$ of dNTP, 10 pmole of each primer set, an annealing temperature of $62^{\circ}C$, and 35 cycles. The optimized condition was successfully employed in a family paternity test.