• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권1호
• /
• pp.27-33
• /
• 1999

Compact fluorescent lamps are very sensitive to the variation of ambient temperature. This paper investigates the temperature characteristics of a 15[W] compact fluorescent lamp, and compensates the variation of light output by frequency control of its electronic ballast. Circuit parameters for the inverter of the electronic ballast are obtained by analyzing the R-L-C equivalent circuit for the inverter and the lamp. The optimum ratio of the two capacitance($C_1$/$C_2$), which are connected with the lamp in series and in parallel, respectively, is determined which consideration of the temperature variation within a range of 10~35[$^{\circ}C$]. As a result a value of 10 for the ratio is obtained at an operating frequency of 57[kHz], and with this value the frequency control works well for temperature compensation. Its validity is verified by investigating light output stabilization characteristics resulting from frequency control of the lamp at various temperatures.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권5호
• /
• pp.640-647
• /
• 1995

In this study, the BaTiO$\sub$3/ capacitor add to MnO$\sub$2/ like depressor and shifter were investigated for temperature or voltage compensation by structural and electrical analysis. The relative density of BCTM, generating poly crystall and formation of lattice defect, has a 90[%] over as the CaTiO$\sub$3/ come out to control grain size. The current density of BCTM2 increased non-ohmic in high-electric field but that BCTM3 and BCTM4 had a few changing. The BCTM3 and BCTM4 unformated grain boundary shown temperature compensation properties, so that the dielectric constant was low value. The curie point was near 140[.deg. C] in BCTM1 and BCTM4, but BCTM3 and BCTM4 not shown the curie point. It is found that the charging energy of BCTM4 was changed 6[%] according to rising temperature from room temperature to 417[K]. The formation of BaMnO$\sub$3/ was low dielectric constant to change frequency and temperature.

• 한국화재소방학회논문지
• /
• 제28권1호
• /
• pp.26-30
• /
• 2014

보상식 화재 감지기는 일정한 온도 상승률 이상으로 빠르게 상승하는 경우에 작동하는 차동식 화재 감지기의 기능과 정온점에 이르렀을 때 작동하는 정온식 화재 감지기의 기능을 모두 가진 감지기다. 이 화재 감지기는 정온점 이하에서 발생하는 화재를 감지하지 못하는 정온식 화재 감지기의 단점과 불꽃없이 천천히 타는 현상과 같이 천천히 열이 증가하는 화재를 감지하지 못하는 차동식 화재 감지기의 단점을 보완하기 위해 개발된다. 이것을 위해 우리는 이 감지기의 센서로 금속-절연체 전이 임계온도센서를 이용했는데 이 센서의 감도를 결정하는 저항온도계수가 $55^{\circ}C$일 때 14.15%로써, 서미스터(약 0.5%)보다 큰 값이다. 이 센서는 하나의 센서가 정온점 이하에서는 차동 기능, 정온점 이상에서는 정온 기능을 모두 가진다.

• Journal of electromagnetic engineering and science
• /
• 제7권3호
• /
• pp.103-108
• /
• 2007

In this paper, a low-power 2.4 GHz front-end for sensor network application (IEEE 802.15.4 LR-WPAN) is designed in a 0.18 um CMOS process. A power supply circuit with a novel temperature-compensation scheme is presented. The simulation and measurement results show that the front-end (LNA, Mixer) can achieve a voltage gain of 35.3 dB and a noise figure(NF) of 3.1 dB while consuming 5.04 mW (LNA: 2.16 mW, Mixer: 2.88 mW) of power at $27^{\circ}C$. The NF includes the loss of BALUN and BPF. The low-IF architecture is used. The voltage gain, noise figure and third-order intercept point (IIP3) variations over -45$^{\circ}C$ to 85$^{\circ}C$ are less than 0.2 dB, 0.25 dB and 1.5 dB, respectively.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.375-379
• /
• 1997

Thermal drift of the machine tool spindle due to temperature increase dominates the major source of the machine tool error. To compensate the thermal errors, software based error correction methods could be implemented. In th~s case, we need model to map the relationship between temperature and thermal distortion. Traditionally, two or three different methods have been trled: step increase of spindle speed, constant, random. The latter two methods are described in the document of ISOlDIS230-3. In this research, three different methods were verified through the experiments from the viewpoint of compensation of thermal distortion. Constant spindle speed turned out good enough for monitoring the behavior of the thermal drift and modeling the relationship between temperature and thermal distortion.

• 대한전자공학회논문지
• /
• 제25권3호
• /
• pp.307-314
• /
• 1988

The thin, square-diaphragm silicon pressure sensor utilizing shear piezoresistance effect was designed and fabricated and its characteristics were examined. The sensor has only one diffused resistor, whereas conventional full-bridge sensor has four. Sensitivity is somewhat lower but temperature compensation is easier than the latter. The proposed sensor was fabricated with only one p-type diffused resistor of the dimension of 113x85\ulcorner\ulcornerlocated near the center of the edge of the diaphragm. The resistor was at 45\ulcornerwith the edge of the diaphragm. The sensitivity of the sensor was 36\ulcorner/V\ulcornermHg and was linear in the pressure range from 0 to 300 mmHg. The temperature coefficient without temperature compensation was 55 ppm/\ulcorner and it was decreased to about 0.17 mmHg/\ulcorner with compensation in the range from 10 to 60\ulcorner.

• 전기학회논문지
• /
• 제61권11호
• /
• pp.1682-1688
• /
• 2012

This paper introduces a GP(Genetic Programming) based robust technique for temperature compensation in short-range prediction. Development of an efficient MOS(Model Output Statistics) is necessary to correct systematic errors of the model, because forecast models do not reliably determine weather conditions. Most of MOS use a linear regression to compensate a prediction model, therefore it is hard to manage an irregular nature of prediction. In order to solve the problem, a nonlinear and symbolic regression method using GP is suggested. The purpose of this study is to evaluate the accuracy of the estimation by a GP based nonlinear MOS for 3 days temperatures in Korean regions. This method is then compared to the UM model and has shown superior results. The training period of 2007-2009 summer is used, and the data of 2010 summer is adopted for verification.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.1298-1300
• /
• 1993

Compensation of temperature is very important to make high precision Load Cell. In this study, we developed a new type of load cell. The structure of the load cell has four strain gauges m single surface of the load cell. Also a new temperature compensation method is proposed and these, characteristics are better than previous one. This study will offer application to other type of load cell end another sensors.

• Journal of Welding and Joining
• /
• 제22권3호
• /
• pp.45-49
• /
• 2004

Generally, it is used the compensation spring to compensate the inaccuracy of screen image induced by thermal deformation in CRT monitor. Its mechanism is hi-metallic system made of heterogeneous metals and these springs are bonded by laser welding. But laser welding induces a non-uniform temperature distribution, and residual stress is yielded locally by these temperature deviation. Therefore, this study measures the curvature constant to assess functions of the compensation spring of shadow mask with respect to increment temperature and estimates the effect of residual stress on the performance of tri-metal used to compensation spring.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2016년도 추계학술대회
• /
• pp.202-205
• /
• 2016

전 세계적으로 해운물류 안전 보안체계가 강화됨에 따라 국가물류보안 체계 구축을 위한 해운물류안전 보안 핵심기술 개발이 이루어지고 있다. 이러한 국제적 정서에 발맞추어, 국내에서도 감마선 핵종을 검출할 수 있는 휴대용 방사선 검출 장치에 대한 관심이 높아지고 있다. 본 논문에서는 방사선 검출에 대한 검사 장비의 성능을 높이려고 온도 보정 Algorithm을 적용한 Digital 휴대용 방사선 검출기 구현에 대한 연구를 제안하고자 한다.