• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.931-934
• /
• 2008

폴리우레탄은 방수재로 널리 사용되며 구조물에 발생되는 균열 및 거동에 의해 항상 외력을 받고있을 뿐만 아니라 사용 환경에 따라 각종 환경열화 인자에 노출되어 있다. 환경 열화인자로서는 자외선, 오존, 열, 수분 등이 잘 알려져 있다. 그 중에서 모든 열화의 기본이 되는 열의 영향, 특히 고온에서의 영향이 중요하다. 따라서, 노출형인 우레탄 고무계 1류 도막 방수재의 경우는 80$^{\circ}C$에서, 비노출형의 경우는 70$^{\circ}$C에서 촉진 열열화 시험을 3주간 실시하였다. 결과는 방수재의 기본물성과 인장 강도 및 신장율 모두 저하되는 경향을 보였으며, 특히 온도 60$^{\circ}$C에서 측정할 경우 급격히 물성 저하가 발생되었다.

• 한국염색가공학회지
• /
• 제24권2호
• /
• pp.121-130
• /
• 2012

Cotton fabrics were treated with some commercial non-formaldehyde and low-formaldehyde resins, and then their effect on the physicochemical properties were respectively investigated including formaldehyde release, tear strength, shrinkage, and wrinkle recovery. Formaldehyde release less than 10ppm was obtained only by non-formaldehyde resin. Considering other factors, the optimal concentration of non-formaldehyde resin was shown to be 9-11%. In case of low-formaldehyde type, 5-7% resin concentration and curing temperature of $160{\sim}170^{\circ}C$ were recommended for optimal finishing condition. The choice and combination of resins and catalysts were also important factors, and preliminary considerations before treating cotton fabrics with resins used in this study are also important to get much better results.

• 펄프종이기술
• /
• 제38권5호
• /
• pp.9-15
• /
• 2006

Wet compaction test (WCT) is a fiber evaluation method where wet fibers are compressed at one side of a cylinder and water drains out from the other side. The consistency of the fiber furnishes and their pressures are recorded during the test. In the previous study we found that WCT results always gave better coefficients of determination in fiber furnish drainage, and paper properties (density, tensile, tear, and burst strength) than those of WRV (water retention value). Fiber freeness and fiber length correlated well with drainage and tear strength of the furnishes, respectively; however, their correlations were very much improved by combining the WCT results. In this study, we used the WCT test for fractionated fiber furnishes to see whether improvement of the WCT is possible. We found that strength properties such as breaking length and burst index were correlated better with the fractionated long fiber furnishes. Drainage was greatly affected by the presence of short fiber furnishes. We used bleached chemical pulps (SwBKP, HwBKP), recycled pulp (OCC), and mechanical pulp (BCTMP) as fiber furnishes in this study. Fiber fractionation can be performed on-line in these days by using multifractor and WCT can be used as an on-line test in papermachine in the future.

• 펄프종이기술
• /
• 제29권1호
• /
• pp.7-12
• /
• 1997

This study was intended to investigate the proper shape and size of calcium carbonate for the improvement of paper properties and its end use performance. We loaded calcium carbonate of various shapes and size in the handsheet and measured their physical and optical properties. Results obtained from the study are summarized as follows : 1. Due to different particle shapes and sizes, precipitated calcium carbonate (PCC) contributed greater to bulk improvement than ground calcium carbonate (GCC). Scalenohedral form of PCC produced the bulkiest sheet, GCC made the sheet bulkier as average particle size increases. 2. Tensile strength increased as average particle size was increasing. GCC kept tensile strength more effectively than PCC. The effect of particle size on tensile strength was much more pronounced as filler addition level was increasing. 3. Over the average particle size of 6.99$\mu$m, GCC gave much higher burst strength and internal bond than PCC did. In the filler levels of 20% and 30%, GCC by using bigger size fillers showed 50~100% improvement in some cases than PCC at the same filler content. 4. Tear strength increased as average particle size was increasing. At the filler level of 30%, PCC decreased tear greatly. 5. Over the average particle size of 13.56$\mu$m, GCC kept bending stiffness greater than PCC. Due to its shape, Scalenohedral form of PCC showed higher stiffness than others at the same particle size. 6. Cubic and acicular form of PCC improved light scattering coefficient very effectively. Light scattering coefficient of GCC decreased as average particle size increased. 7. Both of particle shape and size of filler were important factor in developing optical properties and bending stiffness. Particle size was the only important factor in developing other strength properties

• Elastomers and Composites
• /
• 제46권3호
• /
• pp.186-194
• /
• 2011

셀룰로오스계 천연섬유인 kenaf를 천연고무와 함께 균일하게 배합한 후 압축성형 방법을 사용하여 천연섬유/천연고무 복합재료를 제조하였으며, 이들의 가황거동, 경도, 인장특성, 인열강도 및 정적, 동적 특성에 미치는 kenaf 섬유함량의 영향을 조사하였다. 복합재료를 구성하는 천연섬유의 함량은 천연고무 및 배합제 대비 0, 5, 10, 15, 20 phr이었다. 실험결과 천연고무의 여러 가지 특성이 kenaf 섬유의 함량에 의존한다는 것을 나타내었다. Kenaf 섬유함량이 증가함에 따라 천연고무의 가황에 요구되는 토크는 높아진 반면 가황시간은 감소되었다. Kenaf/천연고무 복합재료의 경도, 인장탄성률과 인열강도는 섬유함량이 증가할수록 점차적으로 증가한 반면, 인장강도와 파단신장률 은 감소하는 경향을 보여주었다. 또한 kenaf 섬유함량이 증가함에 따라 천연고무의 정적 특성보다는 동적 특성의 변화가 더욱 크게 나타났다. 고무에 가해지는 에너지의 감쇄 또는 흡수와 밀접한 관계가 있는 손실인자도 섬유함량에 비례하여 증가하였다.

• 펄프종이기술
• /
• 제43권5호
• /
• pp.34-42
• /
• 2011

A fiber processing method, which might be an alternative for conventional refining process, was introduced. The method consists of repetitive, gentle, mechanical impacts on fibers, followed by fiber uncurling process. This method was very effective for OCC and BCTMP for increasing WRVs (water retention value) while keeping fiber lengths from shortening. For OCC and BCTMP, gentle mechanical impacts on fibers using Hobart mixer increased breaking lengths and tear strengths simultaneously at fast drainage level, and straightening fibers using kady mill increased those strength properties further. For SwBKP and HwBKP, only mechanical impacts using the Hobart mixer were effective on increasing tensile and tear strength at fast drainage, but there were no further increase by kady mill treatment. The strength increases of BCTMP by this alternative fiber processing method were exceptionally high. An extensive engineering development should be followed to actualize this fiber processing mechanism in an energy-effect way.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2006년도 PAN PACIFIC CONFERENCE vol.2
• /
• pp.433-440
• /
• 2006

A fiber processing method, which might be an alternative for conventional refining process, was introduced. The method consists of repetitive, gentle, mechanical impacts on fiber, and ensued fiber uncurling process. This method was very effective for OCC and BCTMP for increasing WRVs (water retention value) while keeping fiber lengths from shortening. For OCC and BCTMP, gentle mechanical impacts on fibers using Hobart mixer increased breaking lengths and tear strengths simultaneously at fast drainage level, and straightening fibers using kady mill increased those strength properties further. For SwBKP and HwBKP, only mechanical impacts using the mixer were effective on increasing tensile and tear strength at fast drainage, but not kady mill treatment. The strength increases of BCTMP by this alternative fiber processing method were exceptionally high. An extensive engineering development should be followed to actualize this fiber processing mechanism in an energy-effect way.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.252-253
• /
• 2021

In this study, butyl rubber, which is the main material constituting the self-adhesive butyl rubber waterproofing sheet, was mixed with reclaimed rubber, and tensile strength, tear strength, peeling resistance strength, and adhesion strength were measured for sample prepared by mixing ratio. As a result, it was confirmed that peeling resistance strength and adhesion strength decreased as the reclaimed rubber content increased, and tensile strength and tear strength did not change significantly.

• 펄프종이기술
• /
• 제39권4호
• /
• pp.45-52
• /
• 2007

Whole, bast and core fibers of kenaf cultivar Tainung-2 were pulped under different pulping methods, thermomechanical and kraft pulping methods. The physical and optical properties of kenaf TMP(thermomechanical pulp) and KP(kraft pulp) handsheets were investigated and the results from the study are summarized as follows: Yields of TMP and KP were $77{\sim}87%\;and\;43{\sim}52%$, respectively. There was no significant change in apparent density between kenaf KP and USKP(unbleached softwood kraft pulp) but TMP showed a little lower apparent density. Bast pulp had the lowest apparent density regardless of pulping methods. Tensile strength of kenaf KP was higher than that of TMP but similar to that of USKP. Both TMP and KP handsheets of bast fraction showed the highest tear strengths among whole, bast, and core fractions. Core fraction showed the lowest tear strengths under different pulping methods. In general burst strength of kenaf pulp under different pulping methods was lower than that of USKP, and kenaf pulp had better stiffness than USKP. Brightness of kenaf KP and TMP was higher than that of USKP. There was no significant variation in opacity between kenaf pulp and USKP even though kenaf pulp showed a little lower opacity. The main difference in paper quality between the core fiber and bast fiber is derived from the fact that bast fiber is long and thin, whereas core fiber is short and thick.

• 펄프종이기술
• /
• 제35권3호
• /
• pp.59-65
• /
• 2003

This research was conducted to investigate the physical properties of Hanji made using maize, konyaku, and wheat powders at various concentrations. Regardless of the starch types, the most effective concentration to increase the physical properties of Hanji was 2 percent. They were significantly improved even at the treatment conditions of 0.1 percent. All the Hanji treated showed the increase of the breaking length, bust index, and tear index and the decrease of the folding number. The strength properties of the Hanji treated were markedly improved at 8 to 10 percent weight increase. The highest mechanical properties were found in the Hanji treated with konyaku powder.