• Elastomers and Composites
• /
• v.40 no.1
• /
• pp.59-65
• /
• 2005

Zinc methacrylate(ZMA) was incorporated into ethylene-propylene diene rubber(EPDM) by direct mixing of the metal salt with the rubber or was in-situ prepared in the rubber matrix through neutralization reaction of zinc oxide(ZnO) and methacrylic acid(MAA). Tensile and tear tests showed that ZMA had a great reinforcing effect for the EPDM. It was also found that ZMA reinforced EPDM vulcanizates can retain their mechanical properties under thermo-oxidative aging. Moreover the incorporation of ZMA induces a substantial improvement in the adhesive strength of the EPDM onto aluminum substrate. The reinforcing effect and an enhancement in adhesion was greatly manifested when the ZMA is in-situ formed with an excess amount of ZnO. The extraordinary improvement in the properties is supposed to be related with the formation of ionic crosslink as well as the degree of dispersion or ZMA domain in the rubber matrix.

• Textile Coloration and Finishing
• /
• v.35 no.4
• /
• pp.246-255
• /
• 2023

In this study, we investigated for natural rubber foam to replace petrochemical-based neoprene foam. Experiments were conducted on vulcanization system and 2-step foaming process of natural rubber. The vulcanization system were EV(Efficient Vulcanization Cure), Semi-EV(Semi-Efficient Vulcanization Cure) and CV(Conventional Vulcanization Cure). In the 2-step foaming process, first molding temperature was 140℃, times were 15, 20, 25, and 30minutes, and the second molding temperature was 160℃, the times 5, 10, 15, and 20minutes. The cure and viscosity characterization were evaluated by oscillating disc rheometer (ODR) and mooney viscosmeter. Various mechanical characteristics, including hardness, tensile strength, elongation at the point of rupture, and tear strength, were quantified. Subsequently, an assessment of alterations in these mechanical attributes was conducted post-immersion in a NaCl solution. In addition degree of volume change was measured after immersing the NR foam in NaCl solution and the low-temperature permanent compression set was evaluated at 4℃. And expansion ratio and shrinkage ratio of NR foam were evaluated for 28 days. As a result the EV vulcanization system showed the least change in physical properties before and after salt water immersion, and the lowest shrinkage ratio for 28 days. In addition it was confirmed that the 2-step foaming optimum condition differed depending on the appropriate vulcanization condition.

• Clinics in Shoulder and Elbow
• /
• v.16 no.1
• /
• pp.47-52
• /
• 2013

Lesions of the long head biceps tendon pulley are frequent causes of shoulder dysfunction and pain. These lesions cause instability of the long head of the biceps tendon (LHB), and intra-articular tear of the subscapularis and the supraspinatus tendon might result from them. The arthroscopic repair of these lesions has not gained widespread acceptance as an effective procedure. Predictable results can be obtained by treating these lesions more definitively with tenotomy or tenodesis. The purpose of this article is to review the anatomy and properties of the LHB pulley and to provide treatment strategies for alleviating pulley lesions.

• Fashion & Textile Research Journal
• /
• v.14 no.4
• /
• pp.635-640
• /
• 2012

In this study, thermoplastic urethane (TPU) coating yarns were prepared at various extruding temperatures. The fine structure and mechanical properties of resultant TPU coating yarns examined by the wide angle X-ray diffractometer (WAXD), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile test. TPU coating yarns (prepared at extruding temperatures at $175^{\circ}C$) were confirmed as a stable fine structure that obtained excellent tensile strength and flexibility. The C samples prepared by optimized conditions made by TPU woven floor mat. The structure of the woven mat is $4{\times}4$ basket weave and have laminated with the EVA foam to obtained final TPU woven floor mat products. The resultant TPU woven floor mat was obtained to 1.5MN of tensile strength, 22% of the elongation, and 0.2MN of tear strength. The weight loss abrasion and the resilience by the ball rebound of the TPU-woven floor mat was prior to those of the PVC subsequently, we were able to develop a woven floor mat with TPU coating yarn and produce an eco-friendly high valuable woven floor mat using an interior product.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.2
• /
• pp.58-67
• /
• 2000

This study was carried out to acquire basic data necessary for the use of non-wood pulp. Various chemical pulping methods for rice straw to achieve higher yield, lower Kappa No. were investigated and then the physical properties of various pulps were tested. The results of this study were as follows: When various chemical pulps (Soda, Soda-AQ, Soda-$H_2O_2$, Soda-$Na_2S_2$, AS, AS-AQ, AS-$Na_2S_2O_3$, AS-$Na_2S_2O_4$, Kraft) were produced with rice-straw, the pulps with the highest yield and lowest Kappa No. were obtained with Soda-$Na_2S_2$and AS-$Na_2S_2O_4$pulps. For the breaking length, Soda and Soda-additive pulps(7.5~9.2km) were better than AS and AS-additive pulps(6.2~8.1km). Similarly, for the burst index, Soda and Soda-additive pulps(6.0~7.0 kPa.$m^2$/g) were better than AS and AS-additive pulps(4.5~6.3 kPa.m$^2$/g). But the tear index was showed 21.8-30.9 mN.$m^2$/g with a little different between pulping methods.

• Journal of Korean Ophthalmic Optics Society
• /
• v.10 no.2
• /
• pp.119-126
• /
• 2005

The purpose of this study was analyzed to compare on the physical characters of two companies of color contact lenses. Artificial tear solution was used for measuring the rate of protein deposits and wettability. The surface roughness of lenses was measured by SEM(scanning electron microscope, Japan) and AFM(atomic force microscope, MultimodeTM, USA). As a results, The color contact lenses was not different from general soft contact lenses in a respect of other properties. However, the colored contact lenses showed a severe crack on the surface under SEM observation. There was no irregularity on the surface of the colored contact lenses in AFM photograph. The dyes were deposited in inside of lenses by microscope observation.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.3
• /
• pp.191-196
• /
• 2004

An emulsion of octadecamidoethylaminoethyl dodecate (which provides softness) and an emulsion silicone oil KF-96 (which provides lubricity) were separately synthesized. Then PP finishing softeners (SSA-7) was prepared by blending of the synthesized emulsions with beef tallow hardened oil (a softness improving agent). PP finishing treatment was carried out with the prepared SSA-7 and PP finishing resin by a one bath method, and several physical properties were tested. As a result, crease recovery, tear strength, softness, lubricity, and bending resistance were all good, indicating that the prepared SSA-7 is a good PP finishing softener.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.669-675
• /
• 2009

A study has been made on the preparation of liquid resin of non-solvent and non-discoloration type for replacement of the soft PVC at room temperature. A new synthetic process was developed by structure-control design of polyurethane synthesis using pre-polymer and polyols as curing agent. The optimum recipe was made according to macro-glycols, molecular weight and reaction conditions, and the final products indicated that the mechanical properties such as tensile strength, tear strength and flexibility was very excellent than PVC products. Also, viscosity, hardness and color operations of the final products can be controlled by this system. And yellowing property by UV and NOx gas was improved from the various additive experiment.

• Elastomers and Composites
• /
• v.35 no.4
• /
• pp.261-271
• /
• 2000

Physical properties of NR vulcanizates cured by both sulfur and resole were studied. Cure characteristics of the compounds were also investigated. Two types of resoles with different molecular weight distributions were employed. The scorch time of the NR compound containing the resole with a low molecular weight distribution was shorter than that of the compound containing the resole with a high one. Crosslink densities of the NR vulcanizates with a high resole content after the thermal aging at $95^{\circ}C$ decreased, while that of the vulcanizate without resole after the thermal aging at $95^{\circ}C$ increased. Though crosslink densities of the NR vulcanizates with a high resole content decreased with increasing the aging time, the moduli increased while the tensile strength and tear strength decreased.

• Macromolecular Research
• /
• v.13 no.2
• /
• pp.81-87
• /
• 2005

Blends of silicone rubber (VMQ) and liquid crystalline polymer (LCP) were prepared by the melt mixing technique. Mechanical, XRD, thermal and dynamic mechanical investigations are reported for the pure silicone rubber and blends. The mechanical properties, viz. the tensile strength, tear strength and elongation at break, of the silicone rubber decreased with the addition of LCP. The SEM study on the tensile fractured surface of the blends revealed that they had a two phase structure, and that the failure was mainly due to fiber pull out, which suggests that the VMQ and LCP are incompatible in all of the proportions examined in this study. However, the FTIR study shows that there was a partial interaction between the VMQ and LCP, but which may not be sufficient to grip the fibrils under the applied load. In the XRD analysis, it was observed that the crystalline structure of the silicone rubber deteriorated in the presence of LCP. The DMA study suggested that the storage modulus of the silicone rubber was improved with the addition of LCP, due to the high modulus of the LCP phase. The thermal stability of the silicone rubber was greatly reduced by the addition of LCP, due to the latter having a thermal stability lower than that of silicone rubber.