• 제목/요약/키워드: tape Casting

검색결과 226건 처리시간 0.025초

Pt 상대전극 성막 두께와 두 기판 간격에 따른 DSSC의 효율 특성 (DSSCs Efficiency by Tape Casting Pt Counter Electrode and Different Thickness Between Two Substrates)

  • 권성열;양욱;주택원
    • 한국전기전자재료학회논문지
    • /
    • 제26권3호
    • /
    • pp.209-215
    • /
    • 2013
  • DSSCs electrical characteristics and efficiency fabricated with different tape casting thickness Pt counter electrodes and different thickness between $TiO_2$ photo electrode and Pt counter electrode substrate were studied. 1 layer Pt counter electrode shows 3.979% efficiency. Efficiency increased as tape casting thickness decreased. The lowest open-circuit voltage was a 0.726 V and the highest short-circuit current was a 2.188 mA on 1 layer Pt counter electrode. On the different thickness between two substrates, the lowest open-circuit voltage 0.712 V and the highest short-circuit current 2.787 mA was measured at $60{\mu}m$ surlyn film thickness and it shows the highest value of 5.067% efficiency.

바인더 함량 변화가 LTCC 그린 테이프의 물리적 특성에 미치는 영향 (Effect of Binder Content on Physical Properties of LTCC Green Tapes)

  • 유정훈;여동훈;이주성;신효순;윤호규;김종희
    • 한국전기전자재료학회논문지
    • /
    • 제19권12호
    • /
    • pp.1112-1117
    • /
    • 2006
  • The properties of LTCC green tape with addition of binder were investigated in order to understand an effects of binder on multilayer processing. A green sheet form was fabricated through tape casting method with the MLS-22 powder. The lamination density increased with increasing amount of binder and lamination pressure. With increasing amount of binder, the elongation of ceramic sheets increased but the tensile stress and air-permeability decreased. The addition of excessive binder is caused defects in the green sheet during via hole punching. The optimum condition of the via hole without defects was observed from amount of the binder 10 wt%.

Rheology of Slurries and Effects of Polymer Volume Ratio in Aqueous PZT Tape Casting

  • Yoon, Seok-Jin;Shin, Hyo-Soon;Lee, Dong-Kyun;Kang, Chong-Yun;Park, Ji-Won;Kim, Hyun-Jai
    • The Korean Journal of Ceramics
    • /
    • 제7권1호
    • /
    • pp.16-19
    • /
    • 2001
  • For the fast dry of the aqueous tape, the process which water was reaplaced by organic solvent was proposed. Socalled, it was the solvent washing dry. Three organic solvents (methanol, ethanol and acetone) were selected for the washing solvent. The weight loss of the washed tapes was measured to evaluate the dry rate of the tapes and dried tapes were examined the generation of the cracks with the variations of the organic solvent and the washing time. Methanol, ethanol and acetone were available organic solvents for this method. The tapes washed in methanol, ethanol and acetone were dried rapidly for twenty minutes. After thirty minutes, the weight losses were not found any more, The solvent of the lower surface tension can decreases the crack of dried tape. If solvent substitutes water completely, though it was fast dried, crack can be eliminated.

  • PDF

Solvent Washing Dry Method for Aqueous Tape Casting

  • Yoon, Seok-Jin;Shin, Hyo-Soon;Park, Ji-Won;Kang, Chong-Yun;Kim, Tae-Song;Kim, Hyun-Jai
    • The Korean Journal of Ceramics
    • /
    • 제7권2호
    • /
    • pp.55-57
    • /
    • 2001
  • For the fast dry of the aqueous tape, the process which water was replaced by organic solvent was proposed. Socalled, it was the solvent washing dry. Three organic solvents (methanol, ethanol and acetone) were selected for the washing solvent. The weight loss of the washed tapes was measured to evaluate the dry rate of the tapes and dried tapes were examined the generation of the cracks with the variations of the organic solvent and the washing time. Methanol, ethanol and acetone were available organic solvents for this method. The tapes washed in methanol, ethanol and acetone were dried rapidly for twenty minutes. After thirty minutes, the weight losses were not found any more. The solvent of the lower surface tension can decreases the crack of dried tape. If solvent substitutes water completely, though it was fast dried, crack can be eliminated.

  • PDF

Li2ZrO3 분리막의 제조와 이산화탄소 선택투과 전후의 기계적 특성 평가 (Fabrication of Li2ZrO3 Membrane and Evaluation on the Mechanical Properties Before and After CO2 Separation)

  • 박상현;이시우;유지행;우상국;이기성
    • 한국세라믹학회지
    • /
    • 제44권1호
    • /
    • pp.58-64
    • /
    • 2007
  • In this study, we investigated $Li_2ZrO_3$ membrane as a candidate material for high-temperature $CO_2$ separation and evaluated mechanical property. $Li_2ZrO_3$ powder was synthesized by solid state reaction of $Li_2CO_3\;and\;ZrO_2$. Then we fabricated $Li_2ZrO_3$ tape using tape casting method. Dense $Li_2ZrO_3$ membrane prepared by sintering at $1600^{\circ}C$ for 2 h after pressing $Li_2ZrO_3$ tape using lamination machine. Mechanical properties before and after $CO_2$ absorption of fabricated $Li_2ZrO_3$ membrane such as Hertzian indentation, Victors hardness and 3-point bending testing were evaluated.

Tape casting 법과 Sandblasting 법을 이용한 광소자용 기판 제조 (1) (Fabration of PLC susbstrate by slurry filling and sandblasting Method)

  • 조윤희;김용석;이용호
    • 한국전기전자재료학회:학술대회논문집
    • /
    • 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
    • /
    • pp.341-345
    • /
    • 2001
  • In this study, nano-sized powders of $Si0_2-0^{\sim}15mol%B_2O_3$ composition were prepared by sol-gel processing method using TEOS(Tetra ethyl ortho silicate) and $H_3BO_3$ solution. The powders were tape-cast on High silicate glass sheet(HSG) substrate and sintered to form a layer of undercladding for the planar light wave module, During the sol-gel processing, $H_2O/Si$ mole ratio were varied to modify the size of the powders in a range from 600 to 75nm. The dispersion of the powder was modified by changing the pH of the slurry. Sintering temperature of the tape was observed to decrease with the size of the powder and the $B_2O_3$ content in the powder. When the silica powders of 75-125nm in diameter containing 15mol% $B_2O_3$ were used, 98 TD% was obtained at $1250^{\circ}C$, which is approximately $300^{\circ}C$ reduction in sintering temperature compared with micrometer-sized powders.

  • PDF

Tape casting법과 Sandblasting법을 이용한 광소자용 기판 제조 (1) (Fabration of PLC susbstrate by slurry filling and sandblasting Method)

  • 조윤희;김응석;이용호
    • 한국전기전자재료학회:학술대회논문집
    • /
    • 한국전기전자재료학회 2001년도 추계학술대회 논문집
    • /
    • pp.341-345
    • /
    • 2001
  • In this study, nano-sized powders of SiO$_2$-0∼15mo1%B$_2$O$_3$ composition were prepared by sol-gel processing method using TEOS(Tetra ethyl ortho silicate) and H$_3$BO$_3$ solution. The powders were tape-cast on High silicate glass sheet(HSG) substrate and sintered to form a layer of undercladding for the planar light wave module. During the sol-gel processing, H$_2$O/Si mole ratio were varied to modify the size of the powders in a range from 600 to 75nm. The dispersion of the powder was modified by changing the pH of the slurry. Sintering temperature of the tape was observed to decrease with the size of the powder and the B$_2$O$_3$ content in the powder. When the silica powders of 75∼125nm in diameter containing 15mo1% B$_2$O$_3$ were used, 98 TD% was obtained at 1250$^{\circ}C$, which is approximately 300$^{\circ}C$ reduction in sintering temperature compared with micrometer-sized powders.

  • PDF

Si$_3$N$_4$ Whisker의 첨가량과 배열방향이 Si$_3$N$_4$ 복합 소결체의 기계적 특성에 미치는 영향 (Effect of the Whisker Amount and Orientation on Mechanical Properties of the Si$_3$N$_4$ based Composites)

  • 김창원;박동수;박찬
    • 한국세라믹학회지
    • /
    • 제36권1호
    • /
    • pp.43-49
    • /
    • 1999
  • 0~5 wt%의 $\beta$-Si3N4 whisker를 첨가한 질화규소 가스압 소결체를 제작하였다. 첨가된 whisker들은 tape casting을 응용하여 tape 내에서 일방향으로 배열하였으며, 제작된 tape로부터 절취된 sheet들의 적층 과정을 변화하여 다양한 미세구조를 갖는 성형체를 제작하였다. 가스압 소결을 통하여 치밀화된 소결체의 조대결정립은 성형체의 whisker와 같은 방향성을 가졌으며, 소결수축률과 기계적 특성 등도 이러한 다양한 미세구조상의 특징과 일관된 결과를 나타내었다. Whisker를 일방향으로 배열하였을 경우, 소결수축률은 whisker 배열 방향과 평행한 방향보다 수직한 방향으로 크게 일어났을 때, whisker 함량이 증가함에 따라 수축률의 차이가 증가하였다. Indentationi crack length는 whisker 함량이 증가함에 따라 whisker 배열 방향과 수직한 방향의 균열 길이는 더 짧아졌고, 그와 평행한 방향의 균열 길이는 길어졌다. Whisker 첨가에 의해 결정립이 더 크게 성장하였으나 강도는 whisker를 첨가하지 않을을때보다 낮지 않았다. Whisker 배열 방향을 90$^{\circ}$ 및 45$^{\circ}$ 간격으로 엇갈리게 적층하였을 경우에는 특성의 이방성이 나타나지 않았다.

  • PDF

$CO_2$ Laser Scribing법을 이용한 PDP용 격벽 제조 (Fabrication of Barrier Ribs for PDP by $CO_2$ Laser Scribing Method)

  • 안정식;이석영;김원용;전형조;이용호;김용석
    • 한국세라믹학회지
    • /
    • 제37권1호
    • /
    • pp.57-62
    • /
    • 2000
  • In this study, an attempt was made to demonstrate the possibility of using laser scribing method in manufacturing the barrier ribs of plasma display panel. The scribing with a CO2 laser was conducted on the green tape produced by the doctor blade tape casting method. Among the processing parameters, the quenching gas pressure, shape of mask, and laser power were found to affect the depth and angle of the scibed barrier ribs.

  • PDF

Acrylate를 결합제로 사용한 수계 테이프 캐스팅에서 알루미나 슬러리의 분산 및 점성 특성 (Dispersion and Rheological Characteristics of Alumina Slurries in Aqueous Tape-casting Using Acrylate Binder)

  • 조유정;박일석;문주호;김대준
    • 한국세라믹학회지
    • /
    • 제39권2호
    • /
    • pp.164-170
    • /
    • 2002
  • Acrylate 수계 결합제를 사용한 알루미나 테이프 캐스팅용 슬러리의 완전분산을 위한 최적의 분산제와 분산제량을 결정하기 위해 침강실험, 분말 함유량 실험, 점도 및 zeta 전위 측정을 행하였다. 알루미나 슬러리의 완전분산은 분산제를 polycarboxylic acid로 했을 때 얻어졌으며, 최적의 첨가량은 알루미나 100에 대하여 0.23∼0.24g 이었다. 분말에 대한 분산제량이 증가할수록 분산은 잘 이루어졌으나, 일정량 이상이 첨가되면 분산제가 용매 안에 과잉으로 존재하여 분산을 저해하는 요인으로 작용하였다. 테이프 캐스팅용 슬러리는 100g의 알루미나 분말에 0.2g의 polycarboxylic acid를 첨가하였을 때 분산 및 테이프 특성이 가장 우수하였고, 이 때 혼합한 결합제는 acrylate였고, 가소제는 Benzoflex를 사용하였다. 이 때 슬러리 최적 점도는 약 570 cps였고, 테이프 내 알루미나 량은 57 vol%이었다.