• Textile Coloration and Finishing
• /
• v.4 no.3
• /
• pp.116-121
• /
• 1992

This paper is on for a material to replace the petroleum-based resins used as adhesives for the fiber in rubber composite materials. The study limited to the reaction properties of tannin with formaldehyde. Tannin-formaldehyde(TF) reactions were carried out in aqueous media. Rates of reaction were strongly dependent on concentration, temperature, pH, and the mole ratio of tannin to formaldehyde. Viscosities of reaction mixtures were followed up to gelation. The reactivity of tannin-formaldehyde resins was greater than that of resorcinol-formaldehyde resins. To formulate an adhesive, a styrene-butadiene-vinyl pyridine terpolymer latex(L) was added to the TF. This preliminary results suggest that the condensed tannins have considerable promise as substitutes for resorcinol used in resin formulation for bonding of fiber to rubber.

• Elastomers and Composites
• /
• v.28 no.4
• /
• pp.274-282
• /
• 1993

Resorcinol-tannin-formaldehyde-latex(RTFL) adhesive was prepared to bond SBR to nylon in reinforced rubber composites. A key factor of adhesive contributes to the adhesion strength between SBR and nylon was the toughness of adhesive itself. Although the stiffness and strength of adhesive film decreased slightly with increasing level of tannin substitution for resorcinol in a standard RFL adhesive, the maximum toughness of adhesive film, which showed yield behavior and high dissipative capacity, was obtain by 60% tannin substitution. However, a marked softening and reduction in toughness occurred at sufficiently high substitution. Also, the adhesive film, which was heat-treated to simulate cure, showed higher strength than the unheated film. Thus, the properties of tannin containing adhesives could be optimized by using 40/60 weight ratio of the resorcinol/tannin in RTFL adhesive composition as well as heat treatment of adhesive film.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.3
• /
• pp.253-264
• /
• 2019

This study characterized the chemical compounds in tannin from mangium (Acacia mangium) bark extract and determined the physical-mechanical properties of glued laminated timber (glulam) made from sengon (Falcataria moluccana), jabon (Anthocephalus cadamba), and mangium wood. The adhesives used to prepare the glulam were based on mangium tannin and phenol resorcinol formaldehyde resin. Five-layer glulam beams measuring $5cm{\times}6cm{\times}120cm$ in thickness, width, and length, respectively, were made with a glue spread of $280g/m^2$ for each glue line, cold pressing at $10.5kgf/cm^2$ for 4 h and clamping for 20 h. Condensed mangium tannin consisted of 49.08% phenolic compounds with an average molecular weight of 4745. The degree of crystallinity was 14.8%. The Stiasny number was 47.22%. The density and the moisture content of the glulams differed from those of the corresponding solid woods with mangium having the lowest moisture content (9.58%) and the highest density ($0.66g/cm^3$). The modulus of rupture for all glulam beams met the JAS 234-2003 standard but the modulus of elasticity and the shear strength values did not. Glulam beams made with tannin had high delamination under dry and wet conditions, but glulam made from sengon and jabon wood met the standard's requirements. All glulam beams had low formaldehyde emissions and were classified as $F^{****}$ for formaldehyde emissions according to the JAS 234 (2003) standard.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.2
• /
• pp.81-97
• /
• 2023

The aim of this study were to evaluate tannin resorcinol formaldehyde (TRF) for the preparation of cross-laminated timbers (CLTs) made from fast-growing tree species and to analyze the physical and mechanical properties of CLTs. TRF copolymer resin was prepared by using the bark extracts of Swietenia mahagoni (L.) Jacq. It was observed that the TRF adhesive possessed less solid content (23.59%), high viscosity (11.35 poise), and high pH values (10.0) compared to the standard phenol resorcinol formaldehyde. The TRF adhesive was applied to produce CLTs with the addition of 15% tapioca and flour as an extender. The six-layered CLTs were produced from sengon (Falcataria moluccana Miq.), jabon [Anthocephalus cadamba (Roxb) Miq.], coconut (Cocos nucifera L.), and the combination of coconut-jabon and coconut-sengon wood. The analysis of variance revealed that the layer composition of CLT significantly affected the physical and mechanical properties of the beam. While the modulus of rupture met the standard, the moisture content and modulus of elasticity values did not fulfill JAS 1152-2007. All of the CLTs produced in this study demonstrated low formaldehyde emission, ranging from 0.001 mg/L to 0.003 mg/L, thereby satisfying the JAS 1152 for structural glue laminated timber.

• Elastomers and Composites
• /
• v.34 no.3
• /
• pp.253-261
• /
• 1999

The cure properties of rubber compounds containing different adhesive compositions were examined. As the amounts of tannin were increased in the adhesive composition, the scorch time was increased and cure rate was decreased due to the size and shape of tannin molecules. Also, the effect of adhesive composition on the adhesion between rubber and fiber was examined by TCAT(Tire Cord Adhesion Test), The reinforcing cords used in this study were mon ofilaments of nylon 610 and nylon 66. According to the results, the optimum adhesion strength between rubber and fiber could be obtained with adhesives whose molar ratios of formaldehyde/resorcinol were above 5/1 in the recipes. Although the level of dip pick-up(DPU) on the reinforcing cord affects the adhesion strength, the DPU of nylon 610 monofilament did not affect the adhesion strength because the level of DPU was constant regardless of the adhesive compositions. In this case, the adhesion strength with the adhesive composition could be explained with the behavior of tannin in the adhesive.

• Elastomers and Composites
• /
• v.29 no.5
• /
• pp.419-425
• /
• 1994

폴리에스테르와 SBR 1502 고무의 접착을 위해 RTFL(resorcinol-tannin-formaldehyde-latex) 접착제를 사용하였다. T-peel geometry를 이용하여 접착력을 평가한 결과 접착제 조성에서 레소시놀과 탄닌이 4대 6의 중량비로 합성된 접착제를 사용한 경우 뛰어난 접착력을 보였다. 폴리에스테르 표면의 소수성과 활성기의 부족에도 불구하고 SBR 고무와 높은 접착력을 보인 이유는 RTFL 접착제 자체의 일정 조성에서 나타나는 toughness 때문이었다. 또한 폴리에스테르와 고무 접착을 위한 single dip 시스템인 N-3형 접착제와 RTFL 접착제를 사용하여 폴리에스테르와 SBR 고무를 접착시킨 후 $-20^{\circ}C{\sim}100^{\circ}C$의 온도 범위와 $0.2cm/min{\sim}50cm/min$의 박리속도 조건아래서 박리 실험하여 얻은 mastercurve들을 비교한 결과 전 범위에서 RTFL 접착제는 기존의 N-3형 접착제와 거의 필적할만한 접착 결과를 나타내었다.