• Membrane Journal
• /
• v.28 no.4
• /
• pp.279-285
• /
• 2018

The pervaporation separation of isopropanol/water mixture was carried out on a series of chemically cross-linked poly(vinyl alcohol)(PVA) composite membranes. The membranes were prepared by casting three kinds of PVA solutions with varying concentrations of PVA and GA onto polyacrylonitrile (PAN) support followed by thermal cross linking. As the PVA concentration increased, the flux decreased but separation factor was increased. It was confirmed that the composite membrane coated with PVA-3 (98~99% hydrolyzed) at a concentration of 7 wt% PVA and 20 wt% glutaraldehyde (GA) exhibited a flux of $209g/m^2h$ and a separation factor of more than 100. The submerged module test was carried out with controlled feed tank temperature and IPA concentration of the feed solution. The continuous concentration of IPA solution was increased from 90% to 99% after 60 h.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.3
• /
• pp.117-127
• /
• 1983

An experimental research was performed employing the two stage anaerobic digestion of the mixture of the nightsoil and septic tank sludge to determine the effects of various hydraulic retention time of the digestion on chemical characteristics and treatment effeciency, thus determining the proper retention time. Results of the research are as follows, 1. Volatile-acid decreased as HRT increased. 2. Alklinity and ammonia-N tended to increase as HRT increased as did pH values, however, were observed to be constant at higher HRT values than 15 days. 3. The removal efficiencies of TBOD, TCOD and VS increased as HRT increased. 4. The removal efficiency of volatile solid decreased as VS loading increased. 5. It was observed that the rates of gas production were: 0.33 with HRT of 5 days, 0.58 with HRT of 15 days and $0.57m^3/kg$ VS fed/day with HRT of 25 days respectively. It is believed that the highest rate of gas production was at HRT of 15 days. 6. The sludge settling experiment showed that the minimum settling time required to ensure the desired underflow concentraton was estimated to be 8.6 days.

• Korean Journal of Weed Science
• /
• v.30 no.2
• /
• pp.143-152
• /
• 2010

Herbicidal characterisitcs of natural product chrysophanic acid were investigated in a greenhouse condition. At early- and middle-stage post-emergence treatments, several grasses and broadleaf weeds appeared to be very susceptible to chrysophanic acid. However, any significant herbicidal activity treated by pre-emergence did not occur at concentration ranges from 31.3 to 1,000 ug $mL^{-1}$. Herbicidal activity of chrysophanic acid estimated by visual injury for large crabgrass was much higher when applied at 7 to 14 days after seeding than at 21 and 28 days after seeding. By post-emergence treatment, chrysophanic acid caused very considerable phytotoxicity on several grasses and broadleaf crops. In herbicidal interaction experiments determined by Colby's method, the effect of chrysophanic acid and caryophyllene oxide tank-mixture showed very high synergistic activity. Although chrysophanic acid did not give any pre-emergence effect, herbicidal spectrum tended to be very wide and strong when treated by post-emergence. These results suggest that chrysophanic acid possesses a possible potential to develop as a natural herbicide.

• Journal of the Korean Data and Information Science Society
• /
• v.21 no.6
• /
• pp.1289-1303
• /
• 2010

The need for statistical process control to check the performance of a process is becoming more important in chemical and pharmaceutical industries. This study illustrates the method to determine whether a process is in control and how to produce and interpret control charts. In the experiment, a stream of green dyed water and a stream of pure water were continuously mixed in the process. The concentration of the dye solution was measured before and after the mixer via a spectrophotometer. The in-line mixer provided benefits to the dye and water mixture but not for the stock dye solution. The control charts were analyzed, and the pre-mixer process was in control for both the stock and mixed solutions. The R and X-bar charts showed virtually all of the points within control limits, and there were no patterns in the X-bar charts to suggest nonrandom data. However, the post-mixer process was shown to be out of control. While the R charts showed variability within the control limits, the X-bar charts were out of control and showed a steady increase in values, suggesting that the data was nonrandom. This steady increase in dye concentration was due to discontinuous, non-steady state flow. To improve the experiment in the future, a mixer could be inserted into the stock dye tank. The mixer would ensure that the dye concentration of the stock solution is more uniform prior to entering the pre-mixer ow cell. Overall, this would create a better standard to judge the water and dye mixture data against as well.

• Geomechanics and Engineering
• /
• v.9 no.4
• /
• pp.447-464
• /
• 2015

Millions of scrap tires are discarded annually in Turkey. The bulk of which are currently landfilled or stockpiled. These tires consume valuable landfill space or if improperly disposed, create a fire hazard and provide a prolific breeding ground for rats and mosquitoes. Used tires pose both a serious public and environmental health problem which means that economically feasible alternatives for scrap tire disposal must be found. Some of the current uses of scrap tires are tire-derived fuel, creating barrier reefs and as an asphalt additive in the form of crumb rubber. However, there is a much need for the development of additional uses for scrap tires. One development the creation of shreds from scrap tires that are coarse grained, free draining and have a low compacted density thus offering significant advantages for use as lightweight subgrade fill and backfill material. This paper reports a comprehensive laboratory study that was performed to evaluate the use of a shredded tire-sand mixture as a backfill material in trench conditions. A steel frame test tank with glass walls was created to replicate a classical trench section in field conditions. The results of the test demonstrated that shredded tires mixed with sand have a definite potential to be effectively used as backfill material for buried pipe installations.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.299-306
• /
• 2005

Anaerobic fermentation of food waste (FW) and waste activated sludge (WAS) for hydrogen production was performed in CSTR (Continuous Stirred tank reactor) under various HRTs and volumetric mixing ratio (V/V) of two substrates, FW and WAS. The specific hydrogen production potential of FW was higher than that of WAS. However, pH drop in the CSTR for hydrogen production from FW was higher than that from WAS. The maintenance of desired pH during fermentative hydrogen production is regarded as the most important operation parameter for the stable hydrogen production. Therefore, when the potential of hydrogen production from FW and better buffer capacity of WAS, the proper mixture of FW and WAS for fermentative hydrogen production were considered as a useful complementary substrate. The maximum yield of specific hydrogen production, 140 mL/g VSS, was found at HRT of 2 day and the volumetric mixing ratio of 20:80 (WAS : FW). The spatial distribution of hydrogen producing bacteria was observed in anaerobic fermentative reactor using fluorescent in situ hybridization (FISH) method.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.12
• /
• pp.1603-1611
• /
• 2009

High-cell-density cultivation of yeast was investigated using the agricultural waste products corn steep liquor (CSL) and molasses. The Saccharomyces cerevisiae KV-25 cell mass was significantly dependent on the ratio between C and N sources. The concentrations of molasses and CSL in the culture medium were statistically optimized at 10.25% (v/v) and 16.87% (v/v), respectively, by response surface methodology (RSM). Batch culture in a 5-l stirred tank reactor using the optimized medium resulted in a cell mass production of 36.5 g/l. In the fed-batch culture, the feed phase was preceded by a batch phase using the optimized medium, and a very high dried-cell-mass yield of 187.63 g/l was successfully attained by feeding a mixture of 20% (v/v) molasses and 80% (v/v) CSL at a rate of 22 ml/h. In this system, the production of cell mass depended mainly on the agitation speed, the composition of the feed medium, and the glucose level in the medium, but only slightly on the aeration rate.

• Fisheries and Aquatic Sciences
• /
• v.16 no.4
• /
• pp.279-283
• /
• 2013

We tested the effects of various distillers dried grains (DDGs) in a formulated diet on growth and body composition of juvenile sea cucumber Apostichopus japonicus. DDG is a solid residue obtained by filtering an aqueous mixture of fermented rice with Aspergillus oryzae and yeasts. Six isonitrogenous and isocaloric diets (DDG0, DDG-G, DDG-C, DDG-K, DDG-W, and DDG-P) were formulated to contain 20% DDG obtained from different Makgeolli factories. Juvenile sea cucumber (average weight, $2.1{\pm}0.02$ g) were randomly distributed in eighteen 50-L rectangular plastic tanks (40 L of water each) in a seawater flow-through system at a density of 50 juveniles/tank. Three replicate groups of sea cucumber were fed each of the six experimental diets at a feeding rate of 5% body weight per day for 22 weeks. At the end of the feeding experiment, survival and weight gain of the juvenile sea cucumber were not affected by the type of dietary DDG (P > 0.05), and the proximate and amino acid compositions of the whole body were not affected by dietary DDG diets (P > 0.05). These results indicate that rice-based DDG is a potential dietary ingredient that could be used at dietary concentrations of up to 20% for growth of juvenile sea cucumber.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.3
• /
• pp.273-285
• /
• 1996

Generally, the flow around the ship's hull often appear 3-dimensional separation at the bow and stem, and the vortex by this flow affects greatly the resistance propulsive efficiency and maneuverability of the ship. This study is compared the calculated result based on the streamlines calculation method with the experimental result by oil fIlm method to analyze the patterns and characteristics of the flows around the ship's hull of chine form. DTMB Series 62, 4667-1 vessel was selected as a sample ship of chine form and model ship was painted with the mixture of oil-color, paint, and poly wax at the surface of the vessel and tested in the model towing tank of Inha University. The results obtained in this study are listed briefly as follows ; 1. For the single chine form, after $4\frac{1}{2}$ station the streamlines are crossed at the chine line and the streamlines are converted to the vortex follow the chine line. 2. For the single chine form, the vortex appered increases and severely in and arround the stern. 3. The approximate streamlines for the ship's hull of chine form can be assigned by the use of the Watanabe's basic transformation formular.

• 한국기계연구소 소보
• /
• s.16
• /
• pp.127-136
• /
• 1986

Recently deck crane of multi purpose cargo vessel (MPCV) is designed to posi¬tion in side instead of in the center line of the upper deck with a view to reduce the transportation cost and shipbuilding cost by shortening the length of ship. In this paper, the crane post was at first designed according to the crane maker’s specification and parent ship and the structure is analysed with Finite Ele¬ment Method. Through the careful reviews on the result of analysis, the final design of crane post was modified. The crane post is designed as a cylindrical in upper part and hexagonal in lower part instead of cylindrical on the whole as before. The connecting part of crane post is designed with the form of mixture of the cylinderical and hexagonal. Since the center of cylindrical and hexagonal section are not on the same line, it is expected to have the stress concentration. So, in order to attenuate the concentrated stress on the connecting part, the upper and lower parts was stiffened by inserting plate to enlarge the area of welding. The structure of deck part includes the tank side floor which is depend on the lower structure of the crane post that would support the force of the crane post by placing with 1.5 frame interval of the vertical plate.