• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.31-34
• /
• 2005

This article has investigated the spatial distribution of the solid particles in polymerization reactors using CFD analysis (FLUENT v. 6.2.1). The suspension of the solids in stirred reactors is affected by a number of parameters including particle diameter, vessel shape, impeller size, impeller speed, and rotating direction of stirrer. The degree of solids suspension in the vessel was quantified with a statistical average value, ${\sigma}^2$. The best stirring conditions were determined based on ${\sigma}^2$, which was found to depend on the vessel bottom shape.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.246-247
• /
• 2005

The paper presents the heat transfer characteristics during cooling process of carbon dioxide($CO_2$) in a helically coiled tube. The main components of the apparatus consist of a receiver, a variable speed pump, a mass flowmeter, a pre-heater, a gas cooler(test section) and an isothermal tank. The test section with the inner diameter 4.55 [mm] is a tube in tube type heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus. The main results were summarized as follows : The heat transfer coefficient increases with respect to the decrease of the gas cooler pressure in a supercritical region and the increase of the refrigerant mass flux. The pressure drop decreases in increases of the gas cooler pressure and increases with respect to increases the refrigerant mass flux.

• Journal of the Korean Society of Visualization
• /
• v.2 no.2
• /
• pp.38-44
• /
• 2004

Theoretical and numerical studies are given to the sink flows within a rotating circular tank driven by the fluid withdrawal from a bottom circular hole. It was found that, when the upper free surface was set with no-slip boundary conditions, the Ekman boundary-layer develops not only above the bottom surface but under the top surface. The sink fluid is coming from the two Ekman layers, and the mass transfer from the bulk, inviscid region is dependent on the rotational speed. It is also remarkable to see that all the fluid gathered along the axis flows in a form of rapidly rotating fluid column haying almost the same diameter as the bottom hole.

• Journal of Ocean Engineering and Technology
• /
• v.32 no.4
• /
• pp.261-271
• /
• 2018

In this study, a hydraulic model test, to which Particle Image Velocimetry (PIV) system applied, was used to determine the hydrodynamic characteristics of the advection-diffusion of saltwater according to bottom conditions (impermeable/permeability, diameter, and inclination) and the difference of the initial salt. Considering quantitative and qualitative results from the experiment, the characteristics of the density current were discussed. As an experimental result, the advection-diffusion mechanism of salinity was examined by the shape of saltwater wedge and the flow structure of density currents with various bottom conditions. The vertical salt concentration obtained from the experiment was used as quantitative data to calculate the diffusion coefficient that was used in the numerical model of the advection-diffusion of saltwater.

• Structural Engineering and Mechanics
• /
• v.51 no.3
• /
• pp.361-375
• /
• 2014

The main aim of this paper is to investigate the relationship between thickness and height of the axially symmetric cylindrical reinforced concrete (RC) walls by the help of a meta-heuristic optimization procedure. The material cost of the wall which includes concrete, reinforcement and formwork, was chosen as objective function of the optimization problem. The wall thickness, compressive strength of concrete and diameter of reinforcement bars were defined as design variables and tank volume, radius and height of the wall, loading condition and unit cost of material were defined as design constants. Numerical analyses of the wall were conducted by using superposition method (SPM) considering ACI 318-Building code requirements for structural concrete. The optimum wall thickness-height relationship was investigated under three main cases related with compressive strength of concrete and density of the stored liquid. According to the results, the proposed method is effective on finding the optimum design with minimum cost.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.835-840
• /
• 2000

The objective of the present study is to investigate the characteristics of pressure wave propagation of viscous fluid flow in a circular pipe line. The goal of this study is to select the best frequency of each control factor of a circular pipe. We intend to approach a formalized mathematical model by a very exact and reasonable polynomial for fluid transmission lines. and we computed this mathematical model by computer. The results show that the oil viscosity decreased as the length of the circular pipe increases. and The energy of pressure wave propagation decreased as the pipe diameter decreases. The factor is that density of oil was changed resonant frequency. It has been found the viscosity characteristics is changed largely by length of hydraulic pipe and volume of cavity tank.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.41 no.5
• /
• pp.77-85
• /
• 1999

Irrigation pipeline systems have been recently adopted for irrigation purposes, which was thought to improve irrigation efficiencies. However, if hydraulic characteristics are not evaluated in designing , overpressure due to waterhammer may occur and result in serious problems. Therefore, in this study a model was formulated to simulate unsteady motion of water in a pipeline resulting from valve closure, the applicability of the model owas tested with fiedld data, and the results showed good agreement in maximum piezometric head. Also, simulated maximum piezometric head was compared with designed piezometric head computed by empirical method, and maximum piezometric head in a pipeline resulting from valve closure was simulated and analyzed with varing surge tank's position and diameter.

• Journal of the Korean Society of Visualization
• /
• v.9 no.3
• /
• pp.38-43
• /
• 2011

When draining takes place through an axially located drain port in a cylindrical tank without any prevent, a vortex with an air core occurs. In this study, semi spherical concave and convex meshes with different size inner hole are used to find the air core can suppress. The study is carried out with different values of inner hole of mesh and different install direction of semi spherical mesh using PIV and measured velocity distribution. By providing a mesh, the air core can be prevented, even if the ratio of inner hole of mesh and diameter of cylinder is around 0.66. The experimental results show that a convex mesh type is more effective to suppress the air core generation than a concave mesh type.

• Water for future
• /
• v.25 no.2
• /
• pp.99-110
• /
• 1992

A problem of outlet salinity from a stratified fluid with a well developed interface thickness consisting of an upper and lower layer differing slightly in density is considered. Three kinds of apparatus were used for the experimental test and salinity differences between inlet layer and outlet discharge were estimated by the functional relationship using the dimensionless values. For the critical incipient condition of withdrawal of upper layer, Densimetric Froude number is correlated by the inlet diameter and depth ratio in the tank.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.28 no.4
• /
• pp.886-889
• /
• 1999

To develope the soybean sprouting equipment(a type of cabinet) for medium amount(one bucket; 10~13kg) production of soybean sprouts, the watering system was made of four siphons and four the bottle necked water tank. Diameter of four siphons used for development of the watering system were 8, 13, 17 and 21mm, respectively and their water exhausting volumes were 40, 92, 154, 524ml/sec, respectively. The watering system can be automatically watered 524ml/sec without electric supply. The soybean sprouting equipment is consisted of four the bottle necked water tanks with the four siphons and six sprouting buckets with net shaped bottom for water draining. The soybean sprouting equipment with the watering system may be produced more than one box a day in the condition of 6~7 watering times a day at 25~30oC.